SuperATV FF-P-RAN900 User manual

© 2020 SuperATV.com®. All Rights Reserved. IN-FF-P-RAN900 3/16/2020
INSTALLATION INSTRUCTIONS
Fender Flares: for Polaris Ranger® XP 900
Thank You
For Choosing
2753 Michigan Road • Madison, Indiana 47250 • 855-743-3427
Need help with your installation?
www.superatv.com
8:00am - 8:00pm EST M-Th
8:00am - 7:00pm EST Friday
9:00am - 2:00pm EST Saturday
[e-mail]
1-855-743-3427
Read instructions and view illustrations before beginning.
Liability Statement
SuperATV’s®products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty
provided by SuperATV®and is not recommended. SuperATV’s® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact
SuperATV®to verify that they will work together.
Although SuperATV®has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine
and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No
warranty or representation is made as to this product’s ability to protect user from severe injury or death. SuperATV®urges operators and occupants to wear a helmet and
appropriate riding gear at all times.
By purchasing and installing SuperATV®products, user agrees that should damages occur, SuperATV®will not be held responsible for loss of time, use, labor fees, replacement
parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any
product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the
product that gave rise to the claim.
SuperATV®will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered
by SuperATV®. SuperATV®parts and products are not warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary
depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and
personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle
safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to
hold SuperATV®harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all
applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV®harmless from any
violation thereof.

2IN-FF-P-RAN900
Lower Left Rear Flare
Lower Left Front Flare
Upper Left Rear Flare
Upper Left Front Flare
Lower Right Rear Flare
Lower Right Front Flare
Upper Right Rear Flare
Upper Right Front Flare

3IN-FF-P-RAN900
Lower Right Front Flare
-Place Clip as close to curve as possible.
- Mark hole location onto Lower Right Front Flare.
- Remove Clip and drill hole through Lower Right Front Flare; use a Ø9/32” drill bit.
- Install Clip over new hole.
Front: driver side installation shown

4IN-FF-P-RAN900
Upper Right Front Flare
Lower Right Front Flare
- Drill hole through Upper Right Front Flare;
use a Ø3/16” drill bit.
-Temporarily join Upper and Lower
Right Flares with Push Pin.
- Mark hole location onto
Upper Right Front Flare.

5IN-FF-P-RAN900
remove stock screws
reuse (2) stock screws
install Upper Right Flare

6IN-FF-P-RAN900
- Secure Upper Right Front Flare to Lower Right Front Flare with hardware shown.
M6 x 30mm
M4 x 16mm
- Secure Flares with hardware shown.

7IN-FF-P-RAN900
repeat steps for opposite side installation
3x - Push Pin
- Secure Upper Right Front Flare with hardware shown.
- Place Upper Right Front Flare against body and drill holes in locations shown; use a Ø5/16” drill bit.

8IN-FF-P-RAN900
Push Pin
stock screw
- Secure Lower Right Rear Flare with hardware shown.
- Place Upper Right Rear Flare onto Lower Right Rear Flare and align to machine.
Rear: driver side installation shown

9IN-FF-P-RAN900
3x - M5 x 40mm
- Secure Upper Right Rear Flare with hardware shown.
5x - Push Pin