SuperATV DOOR-P-RAN900-001 User manual

© 2016 SuperATV.com®. All Rights Reserved. Rev IN-DOOR-P-RAN900-001 2/8/2017
INSTALLATION INSTRUCTIONS
Read instructions and view illustrations before beginning.
Need help with your installation?
1-812-574-7777
[e-mail] www.superatv.com
8:00am - 9:00pm EST M-Th
8:00am - 7:00pm EST Friday
9:00am - 2:00pm EST Saturday
(kit contents continue on following pages)
Item Description
A Passenger Side Door
AB
Full Doors: for Polaris Ranger XP®900
Liability Statement
SuperATV’s® products are designed to best t user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts will
void any warranty provided by SuperATV®and is not recommended. SuperATV’s®
products could interfere with other aftermarket accessories. If user has aftermarket
products on machine, contact SuperATV® to verify that they will work together.
Although SuperATV® has thousands of satised customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride
of machine and may increase maintenance and part wear. Operating any off-road
machine while, or after, consuming alcohol and/or drugs increases risk of bodily
harm or death. No warranty or representation is made as to this product’s ability to
protect user from severe injury or death. SuperATV®urges operators and occupants
to wear a helmet and appropriate riding gear at all times.
By purchasing and installing SuperATV®products, user agrees that should damages
occur, SuperATV®will not be held responsible for loss of time, use, labor fees,
replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held
responsible for any direct, indirect, incidental, special, or consequential damages
that result from any product purchased from SuperATV®. The total liability of seller to
user for all damages, losses, and causes of action, if any, shall not exceed the total
purchase price paid for the product that gave rise to the claim.
SuperATV®will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products will
not be covered by SuperATV®. SuperATV®parts and products are not warrantied if
item was not installed properly, misused, or modied.
Item Description
B Driver Side Door
Thank You
For Choosing
2753 Michigan Road • Madison, Indiana 47250 • 812-574-7777

2IN-DOOR-P-RAN900-001
(kit contents continued)
Item Description
C Hinge Mount; passenger
D Rear Support; passenger
E Hinge Mount; driver
F Rear Support; driver
G Male Hinge; passenger
(Driver Side)
(Passenger Side)
G
J
K
M
H
C
E
F
D
L
Item Description
HStriker Assembly
J Male Hinge; driver
KStrut Bracket; passenger
L Strut
MStrut Bracket; driver
Gasket

3IN-DOOR-P-RAN900-001
M8-1.25 x 25mm Lg.4x
M8-1.25 Nut8x
Mirrors
Cleaning:
- Do not use a dry cloth, or your hands, to wipe off Doors; Scratching will occur.
- Do not use window cleaning uids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
- Never use abrasive cleaners, abrasive pads, or gritty cloths.
1. Thouroughly rinse Doors to oat off dirt and mud.
2. Using a soft cloth, or microber cloth, clean Doors with warm water and a gentle detergent. Baby shampoo or hand
washing soap are recommended.
3. To prevent water spots, use a chamois and blot Doors dry.
(kit contents continued)
M8 Washer12x
M8-1.25 x 20mm Lg.12x
M8 Acorn Nut8x
M5-.80 x 20mm Lg. BHCS4x
M5 Flat Washer4x
M5-.80 Nylock Nut4x

4IN-DOOR-P-RAN900-001
Remove Side Nets and hardware shown from both sides of machine
keep all components removed from machine
(Driver Side)
remove Side Net Buckle and hardware
(Passenger Side)
remove hardware
from Hip Bolster
remove hardware
from Frame
remove Side Net
hardware
(Driver Side)
Floor

5IN-DOOR-P-RAN900-001
- Install Striker Assembly (H) to Frame with hardware shown.
- Loosen Striker Pin as shown below.
- Repeat for opposite side.
Do not tighten hardware completely unless noted.
(Passenger Side)
H
loosen hardware
M8 x 20mm

6IN-DOOR-P-RAN900-001
(Passenger Side)
G
G
C
D
M8 Washer
Qty 2 each per
Hinge Mount
- Install Hinge Mounts (G) to Hinge Mount (C) and Rear Support (D) with hardware shown.
- Repeat for driver side components.
M8 x 20mm
M8 Acorn Nut

7IN-DOOR-P-RAN900-001
(Passenger Side inside machine)
stock hardware
K
C
M8 Nut
L
- Install Hinge Mount (C) to machine with stock hardware as shown.
- Install Strut Bracket (K) to Hinge Mount (C) with hardware shown.
- Install Strut (L) to Strut Bracket (K). Secure with hardware shown.
- Repeat for opposite side.
(Passenger Side)
C
L
stock hardware
2 each
M8 Nut
M8 x 25mm
M8 Washer

8IN-DOOR-P-RAN900-001
- Install provided Gasket to Hinge Mount (C).
- Repeat for opposite side.
A
G
G
(Passenger Side)
(Passenger Side)
Gasket
C
- Install Passenger Side Door (A) to
Male Hinges (G) as shown.

9IN-DOOR-P-RAN900-001
- Secure Strut (L) to Driver Door (B) with hardware shown.
(Driver Side inside machine)
L
B
M8 Nut
- Engage Latch and align Driver Door (B) to machine.
- Tighten all hardware completely.
- Repeat steps for opposite side.

10IN-DOOR-P-RAN900-001
(Driver Side)
M5 Washer
M5 Nut
- Install Mirrors to Doors with hardware shown.
- Tighten hardware completely.
2 each
M5 x 20mm