SuperATV IN-FBG-P-RZR-002 User manual

© 2013 SuperATV.com. All Rights Reserved. IN-FBG-P-RZR-002 2/28/2013
Polaris RZRXP Front Brush Guard
INSTALLATION INSTRUCTIONS
740B Clifty Drive • Madison, Indiana 47250 • 812-574-7777
Liability Statement
SuperATV’s products are designed to best t users ATV/UTV under stock conditions.
Adding, modifying, or fabricating any factory, or aftermarket, parts will void any
warranty provided by SuperATV and is not recommended. SuperATV’s products
could interfere with other aftermarket accessories. If user has aftermarket products
on machine, contact SuperATV to verify that they will work together.
Although SuperATV has thousands of satised customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc will change the ride
of machine and may increase maintenance and part wear. Operating any off-road
machine while, or after, consuming alcohol and/or drugs increases risk of bodily
harm or death. No warranty or representation is made as to this product’s ability to
protect user from severe injury or death. SuperATV urges operators and occupants
to wear a helmet and appropriate riding gear at all times.
By purchasing and installing SuperATV products, user agrees that should damages
occur, SuperATV will not be held responsible for loss of time, use, labor fees,
replacement parts, or freight charges. SuperATV, nor any 3rd party, will not be held
responsible for any direct, indirect, incidental, special, or consequential damages
that result from any product purchased from SuperATV. The total liability of seller to
user for all damages, losses, and causes of action, if any, shall not exceed the total
purchase price paid for the product that gave rise to the claim.
SuperATV will warranty only parts provided by SuperATV. Any damage or problems
with OEM housings, bearings, seals, or other manufacturers products will not be
covered by SuperATV. SuperATV parts and products are not warrantied if item was
not installed properly, misused, or modied.
Read instructions and view illustrations before beginning.
Need help with your installation?
1-812-574-7777
[e-mail] www.superatv.com
8:00am - 9:00pm EST M-Th
8:00am - 7:00pm EST Friday
9:00am - 2:00pm EST Saturday
Thank You
For Choosing

Item Description Qty
A Hoop 1
B Short Grill 1
CFront Bumper 1
DFront Bracket 1
E Left Bracket 1
FRear Bracket 1
GRight Bracket 1
Item Description Qty
HM8 Flat Washers 18
JM8-1.25 x 25mm Lg. Carriage Head Bolts 4
KM8-1.25 x 30mm Lg. HHCS 8
LM8-1.25 Nylock Nuts 18
M M8-1.25 x 20mm Lg. SHCS 4
N5/16” x 3/4” Lg. Self Tapping Screws 2
PM8-1.25 x 25mm Lg. HHCS 2
A
E
C
B
G
D
F
H
K
J
L
M
N
P
(2)
(4)
(18)
(8)
(18)
(2)
(4)
Kit Contents

3
Fig. 1b
Fig. 1c
Remove Grill Insert
(installation illustrations continue on following page)
Remove Hardware
Fig. 1
Bumper
Remove Hardware
Fig. 1a
Bumper
Unplug Headlight Wire Harness’
before removal.
Do not tighten hardware completely unless noted.
Keep stock hardware for reuse.
1. Remove stock Bumper. See Figs. 1 - 1b.
2. Remove stock Grill Insert. See Fig. 1c.
3. Install Hoop (A) to Front Bumper (C) with M8-
1.25 x 20mm Lg. SHCS (M), M8 Flat Washers
(H), and M8-1.25 Nylock Nuts (L); tighten
hardware. See Figs. 2 - 2a.
4. Install Short Grill (B) to Bumper with stock
hardware; tighten hardware. See Fig. 3.
5. Locate (2) mounting holes shown in Fig. 4. and
install Rear Bracket (F) to machine with M8-
1.25 x 25mm Lg. HHCS (P), M8 Flat Washers
(H), and M8-1.25 Nylock Nuts (L). See Figs. 4
- 4a.
6. Reinstall stock Bumper with stock hardware.
7. Install Right Bracket (G) and Left Bracket (E)
to machine with 5/16” x 3/4” Lg. Self Tapping
Screws (N). See Fig. 5.
8. Install Front Bracket (D), as shown in Fig. 6,
with M8-1.25 x 30mm Lg. HHCS (K), M8 Flat
Washers (H), and M8-1.25 Nylock Nuts (L). See
Figs. 6 - 6a.
9. Install Front Bumper (C) to Front Bracket (D)
with M8-1.25 x 25mm Lg. Carriage Head Bolts
(J), M8 Flat Washers (H), and M8-1.25 Nylock
Nuts (L). See Fig. 7.
10. Align to machine and tighten all hardware.

4
secure with stock hardware
Fig. 3
B
Fig. 2
A
C
(installation illustrations continued)
Fig. 2a
H LM
A
C
mounting locations Fig. 4
F
Fig. 4a
F
H LP
Fig. 5
N
EFG
(installation illustrations continue on following page)
Item Description
A Hoop
B Short Grill
CFront Bumper
E Left Bracket
FRear Bracket
GRight Bracket
Item Description
HM8 Flat Washers
LM8-1.25 Nylock Nuts
M M8-1.25 x 20mm Lg. SHCS
N5/16” x 3/4” Lg. Self Tapping Screws
PM8-1.25 x 25mm Lg. HHCS

5
Installed
Fig. 6a
Fig. 6
H
L
D
K
C
Fig. 7
H LJ
(installation illustrations continued)
Item Description
A Hoop
B Short Grill
CFront Bumper
DFront Bracket
E Left Bracket
FRear Bracket
GRight Bracket
HM8 Flat Washers
JM8-1.25 x 25mm Lg. Carriage Head Bolts
KM8-1.25 x 30mm Lg. HHCS
LM8-1.25 Nylock Nuts
M M8-1.25 x 20mm Lg. SHCS
N5/16” x 3/4” Lg. Self Tapping Screws
PM8-1.25 x 25mm Lg. HHCS
PARTS REFERENCE
(3) accessory mounting holes provided