superbrightleds HBR3 Series User manual

Safety and Notes
Retrot Installation Instructions
• Product should be installed by certied electrician in accordance with applicable
national, state, and local building and electrical codes.
• To reduce the risk of electric shock, ensure that the main power source and circuit
breakers are switched o󰀨 before performing any installation or wiring procedures.
• Avoid looking directly into the lamp when illuminated.
• Designed for direct wire installation only, bypassing existing ballasts
where applicable.
• When removing existing ballast reference provided wiring diagram. Apply the
provided label, after installation, in any visible location on the xture.
• Make sure to attach safety cable to secure location during installation.
Caution: When removing ballast, this product must be
installed in accordance with the applicable installation
code by a qualied electrician familiar with the construction
and operation of the product and the hazards involved.
This lamp should be used to replace existing incandescent,
HPS/HID, and CFL lamps with an EX39 or E39 base only.
If used in accordance with these instructions on a UL or ETL
Listed light, the luminaire will retain its original certication.
LED Retrot High Bay Lamp
User Manual
Important: Read all instructions prior to installation. HBR3 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2 07/13/2022
Specications
Model HBR3-50K160-EX39-B
Base Type EX39
Operating
Temperature -40°–122° F (-40°–50° C)
Label containing the following caution needs
to be placed onto the original xture and in a
location that is visible during maintenance.
Caution Risk of Injury or Damage:
This luminaire has been modied to operate
LED lamps. Do not attempt to install or
operate incandescent, HPS/HID, or CFL
lamps in this luminaire.
Retrot Modication Label
Optional Motion Sensor
Retrot Wiring Diagram
5yr
Check product label for specific electrical
specifications related to installation.
Improper installation will void warranty.
The optional microwave motion sensor (HRB3-MS) can be installed
in the lower center area of the bulb by removing the existing threaded
cap, then replacing it with the sensor. The settings on the sensor can
be changed using optional remote (HBR3-RM). Otherwise, the sensor
will operate using default settings.
DEFAULT SETTINGS
Brightness: 100%
Hold Time: 1 minute
Standby Dimming Level: 20%
Standby Time: 1 minute
Sensitivity: 100%
Daylight: Disable
¹applies to bulb only
¹ ¹

LED Retrot High Bay Lamp
User Manual
Important: Read all instructions prior to installation. HBR3 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2 07/13/2022
Optional Remote Control
5yr
The optional remote control (HBR3-RM) can be used with the optional
microwave motion sensor (HRB3-MS) to ne tune settings.
Buttons/Settings
ON/OFF—Press to turn bulb on or o󰀨. Hold until upper settings light up to
enable settings adjustment.
BRIGHTNESS—With adjustment enabled, press the BRIGHTNESS
button to cycle through settings (70% / 80% / 90% / 100%) as indicated
on remote.
SEND—Saves changes. This must be pressed after any adjustments in
order to set them as the current operating settings.
HOLD TIME—With adjustment enabled, press the HOLD TIME button to
cycle through settings (10 seconds / 1 minute / 10 minutes / 30 minutes)
as indicated on remote.
DAYLIGHT—With adjustment enabled, hold the DAYLIGHT button until
the setting indicator lights up, then press the DAYLIGHT button to cycle
through settings (10 lx / 30 lx / 50 lx / 100 lx) as indicated on remote.
SENSITIVITY— With adjustment enabled, press the SENSITIVITY
button to cycle through settings (20% / 50% / 75% / 100%) as indicated
on remote.
STANDBY DIM— With adjustment enabled, press the STANDBY DIM
button to cycle through settings (10% / 20% / 30% / 50%) as indicated on
remote.
STANDBY TIME— With adjustment enabled, press the STANDBY TIME
button to cycle through settings (+∞ / 1 minute / 30 minutes / 60 minutes)
as indicated on remote. Note: +∞ means the standby time will be innite.
RESET—With adjustment enabled, press to reset to default settings.
+ / - —Manually adjust brightness.
¹
¹ ¹
¹applies to bulb only