superbrightleds PLLD3 Series User manual

LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD3 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1.0 03/27/2020
5yr
User Manual
Mounting Options
Safety and Notes
Environmental Specications
Operating Temperature -40°–122° F(-40°–50° C)
IP Rating IP65
Adjustable Pole Mount (PLLD3-APM)
Adjustable Slip-tter/Pole Mount (PLLD3-SFPM)
U-bracket/Yoke Mount (PLLD3-FM1 and PLLD3-FM2)
Wall/Trunnion Mount (PLLD3-WM)
•Product should be installed and serviced by a certied electrician
in accordance with applicable national, state, and local building
and electrical codes.
• To reduce the risk of electric shock, ensure that the main power
source and circuit breakers are switched o󰀨 before performing
any installation or wiring procedures.
• Avoid looking directly into lamp when illuminated.
• Ensure all mounts are securely attached and will support the
weight of the xture. Failure to properly support xture may
result in damage or injury, for which the manufacturer does not
assume responsibility.
Specications
PLLD3-50K300-S30T3-BRSF
Check product label for specific electrical
specifications related to installation.
Improper installation will void warranty.
Wiring Diagram
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green

LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD3 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1.0 03/27/2020
5yr
User Manual
Pole/Post Knuckle Mount (PLLD3-SFPM) Installation
Round Pole
Mounting Only
Square and Round
Pole Mounting Only
Pole/Post Installation
1. Remove included slip-tter mount.
2. Disassemble mount and
run wiring through it.
3. Reassemble mount.
4. Attach mount to light.
5. Drill mounting holes in pole/post and
attach mount.
Note: Installation on square poles will not require
round pole adapter plate or gasket. See illustration.
6. With supply power o󰀨, use access panel
to connect wiring.
7. Rotate light to desired angle and
tighten adjustment screw.
Slip-tter Installation
1. Remove included slip-tter mount.
2. Disassemble mount and run wiring through it.
3. Reassemble mount.
Note: Discard Pole/Post mount components.
4. Attach mount to light.
5. With supply power o󰀨, connect wiring.
6. Slide mount over pole/post and secure in place. The
maximum pole/post diameter is 2.375 in.
7. Rotate light to desired angle and tighten adjustment screw.

LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD3 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1.0 03/27/2020
5yr
User Manual
U-bracket/Yoke Mount (PLLD3-FM1, PLLD3-FM2) Installation
1. Remove included slip-tter mount.
2.Use U-bracket mount as a template to make mounting holes
on wall/surface and install hardware.
3.Attach the light to the bracket
4.Mount light to surface.
5.With supply power o󰀨, connect wiring.
6.Once installation is complete, the position locking bolts can
be removed and the center trunnion bolts can be loosened
to adjust the mounting angle of the light. Reinstall the position
locking bolts and retighten center bolt when the desired
angle is achieved.
1. Remove included slip-tter mount.
2.Remove side access plate cover
on mount.
3.Run wiring through the ange that
attaches to the light.
4.Secure ange to light.
5.Make appropriate mounting and wiring
holes in pole/post and attach mount to
pole/post.
6.With supply power o󰀨, use side access
to connect wiring.
7. Losen adjustment bolt to adjust angle.
Rotate light to desired angle and
tighten adjustment screw.
8.Re-install side access plate cover.
Adjustable Pole/Post Mount (PLLD3-APM) Installation

LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD3 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1.0 03/27/2020
5yr
User Manual
1. Remove included slip-tter mount.
2.Use trunnion mount as a template to make mounting
holes on wall/surface and install hardware.
3.Run wiring through the ange then attach the light
to the bracket.
4.Mount light to surface.
5.With supply power o󰀨, connect wiring.
6.Once installation is complete, the position locking
bolts can be removed and the center trunnion bolts
can be loosened to adjust the mounting angle of the
light. Reinstall the position locking bolts and retighten
center bolt when the desired angle is achieved.
Trunnion Wall/Surface Mount (PLLD3-WM) Installation