superbrightleds PLLD Series User manual

LED Dimmable Parking Lot Light
User Manual
Part Number:
Important: Read all instructions prior to installation. PLLD Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2.0 1/02/2019
5yr
Mounting Options
Product Safety and Notes
Knuckle Mount Slip Fitter Kit (PLL-KM)
• This product should be installed by a fully
certied electrician in accordance with
local building and electrical codes.
• Due to risk of electric shock, ensure
that the main power source and circuit
breakers are switched o󰀨 before
performing any installation or wiring
procedures.
• Failure to properly support the xture
during installation may cause damage or
injury, for which the manufacturer is not
responsible. Ensure the light bracket/eye
bolt is securely mounted and will support
the weight of the xture.
Wiring Diagram
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green
Universal Arm Mount Kit Round/Square Pole (PLL-PM)
Trunion Mount Kit (PLL-TM)Wall Mount Kit (PLL-WM)

LED Dimmable Parking Lot Light
WIFI-CON
User Manual
Part Number:
Important: Read all instructions prior to installation.
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2.0 1/02/2019
1. Remove power prior to installation.
2. Remove 2 screws from wire access cover plate and feed wires
through slip tter cavity to exit bottom of mount.
3. Attach slip tter mount to light xture using (x4) M8x30mm
screws with 6mm allen wrench (not included).
4. Connect xture wire leads to supply wires. (See Wire Diagram)
5. Loosen pole set screws from slip tter base and slide slip tter
on top of pole.
6. Tighten pole set screws on side of slip tter to attach to light
pole.
7. Adjust angle per application by loosening socket head
cap screw inside wire access cavity with 10mm allen (not
included).
8. Reinstall wire access cover plate.
1. Remove 2 screws from wire access plate.
2. Loosen socket head cap screw inside wire access cavity with 10mm allen (not included).
3. Remove slip tter mount to light xture using (x4) M8x30mm screws with 6mm allen
wrench (not included).
Slip Fitter Removal
Installation
Round/Square Installation (PLL-PM)
Knuckle Mount Slip Fitter Removal and Installation (PLL-KM)
PLLD Series
2.00in
50.80mm
3.06in
77.72mm
4.59in
116.59mm
3.11in
78.99mm
3.99in
101.41mm
2.53in
64.26mm
45.00° 45.00°
M8 x 30mm
Allen Screw
Assembly (x4)
Knuckle Mount
Slip Fitter
2.00in
50.80mm
3.06in
77.72mm
4.59in
116.59mm
3.11in
78.99mm
3.99in
101.41mm
2.53in
64.26mm
31
0°
90.00°
0°
90.00°
Wire Access
Plate
2.00in
50.80mm
3.06in
77.72mm
4.59in
116.59mm
3.11in
78.99mm
3.99in
101.41mm
2.53in
64.26mm
31
0°
90.00°
0°
90.00°
Wire Access
Plate
5yr
1. Remove screw from wire access plate on mount
arm and remove plate.
2. Use pole mount plate to mark hole pattern on
outside of pole. Drill three mounting holes for
M8 mounting screws. Drill one hole for wiring.
3. Place pole mount plate inside pole with
corresponding at or convex
mating surface toward pole. Loosely thread two
M8 mounting screws
into plate—through pole—to hold the plate in place.
4. With the proper gasket (round pole) or gaskets (square
pole) in place.
Slide the mount arm over the two partially installed screws.
5. Thread the third mounting screw through the mount arm and pole into
the mount plate and then tighten all three mount screws.
6. Run wire leads through large hole of pole mount into wire access area.
7. Run light wiring into wire access area and attach light to mount using
four M8 screws.
8. Connect wiring and reinstall wire access plate.
used in both installation types
used in square pole installation only

1. Attach Trunnion Mount to xture using M8 screws and nuts. Secure with allen wrench
until lock washer is fully compressed.
2. Drills holes into application using the drill template for proper width.
3. Attach xture to application using the provided hardware.
4. Connect wiring to power supply wires. Black to Line, White to Neutral, and Green to
Ground. If 1~10V dimming is used, connect Purple to DIM+ and Gray to DIM-. Consult
electrician and install according to national, local, and state codes.
1. Install Wall Mount to light xture.
2. Drill 2 .4375” holes following drill template.
3. Attach xture to wall mount and adjust angle per application. Secure
with M8x30mm long socket head cap screw with 6mm allen (not
included).
4. Connect wiring to power supply wires. Black to Line, White to Neutral, and
Green to Ground. If 1~10V dimming is used, connect Purple to DIM+ and
Gray to DIM-. Consult electrician and install according to national, local,
and state codes.
5. Adjust angle using M4x16mm screw (one only provided).
Wall Mount Installation (PLL-WM)
100W, 150W, 200W PLLD Series
LED Dimmable Parking Lot Light
User Manual
Part Number:
Important: Read all instructions prior to installation.
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2.0 1/02/2019
Trunnion Mount Installation
Dimensional Drawings
PLLD Series
0°
90.00°
0°
90.00°
5.48in
139.19mm
3.32in
84.37mm
4.14in
105.16mm
5.88in
149.35mm
5.46in
138.63mm
1.94in
49.28mm
.80in
20.32mm
.29in
7.37mm
R.17in
4.32mm
2.68in
68.07mm
3.26in
82.80mm
3
Wall Mount
M8 x 30mm screw
Assembly (x4)
M8 x 20mm screw
Assembly (x2)
M4 x 16mm screw
13.00in
330.20mm
10.31in
261.96mm
2.20in
55.88mm
3.94in
100.08mm
TRUE
R.33in
8.36mm
TRUE
R.33in
8.36mm
TRUE
R.20in
5.08mm
5
0°
45.00°
90.00°
0°
45.00°
90.00°
13.00in
330.20mm
10.31in
261.96mm
2.20in
55.88mm
3.94in
100.08mm
TRUE
R.33in
8.36mm
TRUE
R.33in
8.36mm
TRUE
R.20in
5.08mm
5
0°
45.00°
90.00°
0°
45.00°
90.00°
11.02in
279.94mm
2.88in
73.15mm
12.56in
319.09mm
.39in
9.87mm
1.39in
35.21mm
2.56in
65.09mm
11.00in
279.40mm
3.96in
100.63mm
300W PLLD Series
12.56in
319.09mm
11.18in
283.85mm
2.95in
75.02mm
.39in
9.91mm
1.40in
35.56mm
2.56in
65.09mm
18.25in
463.55mm
3.96in
100.58mm
12.56in
319.09mm
11.18in
283.85mm
2.95in
75.02mm
.39in
9.91mm
1.40in
35.56mm
2.56in
65.09mm
18.25in
463.55mm
3.96in
100.58mm
12.56in
319.09mm
11.18in
283.85mm
2.95in
75.02mm
.39in
9.91mm
1.40in
35.56mm
2.56in
65.09mm
18.25in
463.55mm
3.96in
100.58mm
5yr

LED Dimmable Parking Lot Light
User Manual
Part Number:
Important: Read all instructions prior to installation. PLLD Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2.0 1/02/2019
Accessory Dimensional Drawings
2.00in
50.80mm
3.06in
77.72mm
4.59in
116.59mm
3.11in
78.99mm
3.99in
101.41mm
2.53in
64.26mm
45.00° 45.00°
M8 x 30mm
Allen Screw
Assembly (x4)
Knuckle Mount
Slip Fitter
0°
90.00°
0°
90.00°
5.48in
139.19mm
3.32in
84.37mm
4.14in
105.16mm
5.88in
149.35mm
5.46in
138.63mm
1.94in
49.28mm
.80in
20.32mm
.29in
7.37mm
R.17in
4.32mm
2.68in
68.07mm
3.26in
82.80mm
3
Wall Mount
M8 x 30mm screw
Assembly (x4)
M8 x 20mm screw
Assembly (x2)
M4 x 16mm screw
Knuckle Mount Slip Fitter Kit (PLL-KM)
Universal Arm Mount Kit Round/Square Pole (PLL-PM)
Universal Arm Mount Kit Square Pole (PLL-SPM) Trunion Mount Kit (PLL-TM)
13.00in
330.20mm
10.31in
261.96mm
2.20in
55.88mm
3.94in
100.08mm
TRUE
R.33in
8.36mm
TRUE
R.33in
8.36mm
TRUE
R.20in
5.08mm
5
0°
45.00°
90.00°
0°
45.00°
90.00°
5yr
0.85 in.
(21.59 mm)
pole mount plate
Fig. 1 (3:1 scale)
2.78 in.
(70.61 mm)
0.47 in.
(12 mm)
Ø 0.31 in.
(8 mm)
4.68 in.
(118.87 mm)
1.93 in.
(49.02 mm)
5.5 in.
(139.7 mm)
7.78in
197.70mm
5.50in
139.70mm
2.06in
52.32mm
2.58in
65.53mm
4.50in
114.30mm
2.58in
65.53mm