superbrightleds WPA-xK12-W User manual

Adjustable LED Wall Pack
Important: Read all instructions prior to installation. WPA Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1.0 08/30/2019
5yr
User Manual
Specications
Safety and Notes
Wiring Diagram
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green
• Product should be installed and serviced by a certied electrician in accordance
with applicable national, state, and local building and electrical codes.
• To reduce the risk of electric shock, ensure that the main power source and circuit
breakers are switched o󰀨 before performing any installation or wiring procedures.
• Avoid looking directly into lamp when illuminated.
• Ensure all mounts are securely attached and will support the weight of the xture.
Failure to properly support xture may result in damage or injury, for which the
manufacturer does not assume responsibility.
Model WPA-xK12-W WPA-xK35-W WPA-xK75-W WPA-xK120-W
Voltage 120 –277 VAC
Wattage 12 W 35 W 75 W 120 W
Current 0.1 A @120 VAC 0.29 A @120 VAC 0.63 A @120 VAC 1 A @120 VAC
Beam Angle 75° x 100° (NEMA 5 x NEMA 6)
Operating Temperature -40°–122° F (-40°–50° C)
IP Rating IP65
Dimming yes (0–10 V)
Photocell can be installed into any
available conduit hole. Wire according
to wiring diagram.
WPA-xK75-W
Photocell Installation
Photocell
Line
Neutral
Ground Green
White
White Red Black
Black
Light

Adjustable LED Wall Pack
Important: Read all instructions prior to installation. WPA Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1.0 08/30/2019
5yr
User Manual
Wall/Junction Box Installation
Conduit Installation
Front Housing
Light Angle Adjustment Bolt
Rear Housing
Dimming Wiring
(optional)
Gasket
(preinstalled)
Conduit
Junction Box
(not included)
Note: Light angle can be adjusted in 10°
increments within a 90° range.
Note: Light angle can be adjusted in 10°
increments within a 90° range.
1. Loosen light angle adjustment bolts and
rotate light up.
2. Remove two screws that hold front and rear
housing together.
3. Rotate light and front housing out and lift o󰀨
of rear housing.
4. With supply power turned o󰀨, run wiring
through rear housing and mount housing to
junction box/wall.
5. Slide front housing and light back onto the
rear housing in open position and connect
wiring.
6. Close light xture and secure with two
screws.
7. Apply power. Use adjustment bolt to set light
at desired angle.
1. Loosen light angle adjustment bolts and rotate
light up.
2. Remove two screws that hold front and rear
housing together.
3. Rotate light and front housing out and lift o󰀨 of
rear housing.
4. Mount housing to wall and attach conduit.
5. With supply power turned o󰀨, run wiring into
rear housing.
6. Slide front housing and light back onto the rear
housing in open position and connect wiring.
7. Close light xture and secure with two screws.
8. Apply power. Use adjustment bolt to set light at
desired angle.