Surefire LumaMax L1-HA-Series User manual

Model L1-HA-xx
L1 LumaMax™ LED Flashlight
One-Watt Digitally Controlled LED
Flashlight with Dual Output Beam
Operator’s Manual
Revision B 8-1-2005

L1 LumaMax LED
Introduction
The L1 LumaMaxTM is fitted with a one-watt LED
(Light Emitting Diode) powered by a single 3-volt
battery. The LumaMax features digital current
regulation circuitry and a digitally controlled two-
stage switching mechanism. The current
regulation circuitry matches the LED’s current
requirements to the batteries’ output to achieve a
more consistent (flatter) level of light output for the
useable life of the batteries. The two-stage switch
gives the user a choice of either a low-output beam
or a high-output beam from a single switch. The
LumaMax is available in four LED colors: White
(WH), Blue (BL), Green (GN), and Red (RD).
Light Activation
Depressing the pushbutton switch halfway
activates the low-output beam. Depress pushbutton
completely to activate high-output beam. The light
will stay on as long as the pushbutton is depressed.
For constant-on activation, rotate tailcap clockwise
until LED activates and continue rotating to
activate high-output beam.
Note: If light fails to function, the tailcap may be in
the lock-out position. Rotate the tailcap clockwise
until the light can be momentarily activated.
This unit has approval

Operation
Lock-out Tailcap (U.S. Patent Number 6,222,138)
The lock-out position is suggested to avoid
accidental light activation during storage or
transport. From the momentary-on position, rotate
the tailcap approximately one and one half turns
counter-clockwise to lock the light in the OFF
position.
Battery Replacement
Unscrew the tailcap and insert new battery with
positive end towards LED assembly. Replace
tailcap and rotate clockwise to the momentary-on
position. Depress tailcap pushbutton switch to test.
WARNING: Lithium batteries can explode or
cause burns if disassembled, shorted, recharged or
exposed to fire or high temperatures. Do not
expose contents to water, mix with used or other
battery types, or put in backwards.
Maintenance
Twice yearly (or more frequently depending on
usage) clean and lubricate threads with clean cloth
and apply thin coat of silicon-based lubrication to
rubber O-rings. Note: DO NOT use petroleum-
based lubrication on SureFire O-rings. After
prolonged exposure to moisture, the bezel, lamp,
and batteries should be removed, inspected, and
dried if necessary. Note: After removal and
reinstallation, the bezel, must be tightened firmly
or the light will not activate.
Caution
Make sure the Lamp is off before storage to
prevent damage caused from overheating the
Lamp or nearby objects.

SureFire®
LED ASSEMBLY
FLASHLIGHT BODY
SF123A
BATTERY
LOCK-OUT TAILCAP

L1 LumaMax LED
SureFire L1 LumaMax
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Output & Runtime
Accurately specifying light output (lumens) and
runtime is more complicated for LED flashlights
than for tungsten lamp flashlights due to slight
variation in LEDs and LED output characteristics.
L1 light output if continuously run:
High Output: Maximum 15 lumens for 1.5 hours,
then 1 hour of gradually diminishing light, then 2+
hours of minimal light.
Low Output: Maximum .65 lumens for 25
hours, then 200 hours of gradually diminishing
light.

L1 LumaMax LED
Warranty Claims
For repair or replacement contact Customer
Service at 800-828-8809 (toll free) or 714-
545-9444 and obtain a Return Merchandise
Authorization number (RMA#). Then
package the unit carefully and return (no
COD’s please) to:
SureFire
Repairs Department, RA#___
17680 Newhope Street, Suite B
Fountain Valley, CA 92708-6122
SureFire will pay any reasonable shipping
costs to return the unit to you.
Warranty
SureFire®warrants its products to be free
from defects in materials and workmanship.
SureFire will repair or replace, at its option
without charge, any product or part which is
found to be defective under normal use and
service. Such repair or replacement shall be
the purchaser’s sole and exclusive remedy
under this warranty. This warranty does not
include normal maintenance and services
and does not apply to any products or parts
that have been subjected to modification,
misuse, negligence, accident, improper
maintenance or repair by anyone other than
SureFire.
Warranty Limitation
There is no other express warranty.
SureFire®hereby disclaims any and all
implied warranties, including but not limited
to fitness for a particular purpose. SureFire
shall not be liable for incidental,
consequential, or special damages arising
out of, or in connection with, product use or
performance. UM_L1
71-01-608
18300 Mt. Baldy Circle, Fountain Valley, CA 92708-6122
www.surefire.com 800-828-8809