Swiss Madison SM-2T130 User manual

®
INSTALLATION
INSTRUCTIONS
Classe Two-Piece Elongated Toilet
SM-2T130
www.swissmadison.com | 1-434-623-4766 | [email protected]
Share your pictures for a feature
using #SwissMadison
S
wiss
M
adison
®

Prior to Installation:
If you have any questions or concerns please contact us:
1-434-623-4766
[email protected]
General Recommendation: Read installation and maintenance instructions thoroughly before installing.
Be sure to use proper tools and always wear proper personal safety accessories for your protection.
—1 —
Inspect toilet to ensure no damages have occurred while in shipping.
Observe all plumbing and building codes in accordance with your state and local requirements.
Remove old toilet.
Make sure mounting surface is CLEAN and LEVEL.
All dimensions are nominal! Be sure to measure your toilet prior to installation.

—2 —
Thank you for purchasing a Swiss Madison Two-Piece Toilet.
We appreciate your business and know you will enjoy your toilet for many years to come.
If you have any questions or require assistance we would be happy to help,
please contact us at 1-434-6234766 or [email protected].
Thank you for your purchase!
www.swissmadison.com
To learn more about our products, please visit:
Sincerely,
The Swiss Madison Team

TWO-PIECE TOILET ROUGH DIMENSIONS
—3 —
NOTE: Specialized tools may be necessary to install a Swiss Madison Two-Piece Toilet, plumbing not included.
SUGGESTED TOOLS AND MATERIALS
Two-Piece Toilet Wax Ring / Gasket Bolts Side Cover Caps
NOTE: Distance from wall to closet flange centerline must be listed as below.
Safety Glasses Wrench Level
Putty Knife Tape Measure
ScrewdriverHacksaw
Flexible Supply Tube
PARTS LIST
NOTE: All measurements are nominal.
15 7⁄8”
7 ¹⁄16”
18 5⁄8”
28 9⁄16”
16 ³⁄4”
12”
32 ¹⁄4”
Rough-in

TWO-PIECE TOILET INSTALLATION INSTRUCTIONS
1. Read the complete instruction manual before beginning installation.
2. Confirm that your model will fit in intended location and plumbing fixtures are located where
legally required before beginning installation.
3. Not all drawings on this manual are drawn to scale. Please refer to the model chart.
4. Two people are recommended to install and move this product.
5. Product is FRAGILE! To avoid breakage and possible injury handle with care.
—4 —
NOTE: Drawings may not exactly define contour of china.
The step-by-step guidelines in the installation instructions are a general reference for installing a Swiss Madison Two-Piece Toilet.
Should there be any discrepancies, Swiss Madison cannot be held liable.
It is recommended to install all Swiss Madison products by hiring a licensed professional
2. Rough-in the Toilet
· Using the measurements on the previous page find the toilet’s rough-in.
· Measure the wall from behind the toilet to the middle of the closet bolt.
NOTE: Your rough-in measurement should be around 12”.
Rough-in
1. Remove Old Toilet
· Close toilet supply valve and flush tank completely, use towel or sponge to remove excess water.
· Disconnect and remove supply line. If you are replacing the valve, shut off the main water supply first.
· Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping gas.
· Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

TWO-PIECE TOILET INSTALLATION INSTRUCTIONS
—5 —
NOTE: Drawings may not exactly define contour of china.
3. Install Closet Bolts
· Install closet bolts to flange channel, turn 90° and slide into place 6” (152 mm) apart and parallel to wall.
Closet Flange
Closet Bolts
A
4. Install Wax Seal
· Invert toilet on floor (use cushion to prevent damage), and install wax ring evenly around waste flange
with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.
Wax Ring
Sealant

TWO-PIECE TOILET INSTALLATION INSTRUCTIONS
NOTE: Drawings may not exactly define contour of china.
—6 —
5. Connect Supply Hose
· Thread the supply hose onto the tank.
6. Attach Gasket
· Position the gasket on the bowl inlet.
7. Position Tank onto Bowl
· Holes should line up so threaded rod can fit smoothly, connecting the cistern body to the bowl.

TWO-PIECE TOILET INSTALLATION INSTRUCTIONS
NOTE: Drawings may not exactly define contour of china.
T
H
I
S
S
I
D
E
U
P
9. Position Toilet on Flange
· Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes.
· Loosely install retainer washers and nuts. Side of washers marked “THIS SIDE UP” must face up!
Closet Flange
Nut
Washer
Bolt
—7 —
8. Secure Tank to Bowl
· Slide the metal washer and the rubber washer onto the bolt.
· Thread the bolts into the bottom of the tank tighten the bolts using a screwdriver.
NOTE: Do not overtighten! Overtightening can lead to the ceramic cracking.
Rubber Washer
Metal
Washer Bolt

TWO-PIECE TOILET INSTALLATION INSTRUCTIONS
NOTE: Drawings may not exactly define contour of china.
—8 —
10. Install Toilet
NOTE: Do not overtighten! Overtightening can lead to the ceramic cracking.
· Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly sealed to the floor.
· Adhere bolt covers to toilet.
· Smooth off the bead of sealant around the base. Remove excess sealant.
T
H
I
S
S
I
D
E
U
P
Closet Flange
Bolts
11. Secure Tank
· Use screws and washers to affix the tank to the wall.
· Tighten to secure into place, do not over tighten.
12. Connect Plumbing
· Connect water supply and turn on water.
³⁄8” Supply

TWO-PIECE TOILET INSTALLATION INSTRUCTIONS
NOTE: Drawings may not exactly define contour of china.
—9 —
14. Check for Leaks
· Flush several times and check for leaks.
13. Connect Push Button
· Unscrew the big nut on the push button and insert the button into the hole on the tank.
· When the rods meet the push buttons, measure the height (H) with a ruler.
· Unscrew the rods and cut the part to height (H) on both rods.
· Insert the rods back and tighten the small nut.
· Tighten the big nut from the inside of the tank.
Push Button
Rubber Sleeve
Small Nut HTank Cover