SWIT S-1071H(EFP) User manual

Model: S-1071H(EFP)
7" EFP Field On-camera LCD Monitor
User Manual
Please read this User Manual
throughout before using

Preface
Congratulations on your purchase of this product Please read this user manual carefully
1 ． All internal technologies of this product are protected, including device, software and trademark
Reproduction in whole or in part without written permission is prohibited
2 ． All brands and trademarks of SWIT Electronics Co , Ltd are protected and other relative trademarks
in this user manual are the property of their respective owners
3 ． Due to constant effort of product development, SWIT reserves the right to make changes and
improvements to the product described in this manual without prior notice
4 ． The warranty period of this product is 2 years, and does not cover the following:
(1) Physical damage to the surface of the products, including scratches, cracks or other damage to
the LCD screen or other externally exposed parts;
(2) Misuse, abuse or negligent operation to the product;
(3) The product is disassembled by anyone other than an authorized service center
It is considered normal that the LCD bright dot defects are not to exceed three
5 ． For any suggestions and requirements on this product, please contact us through phone, fax, Email,
etc
SWIT Electronics Co. Ltd.
Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone,
Nanjing 210038, P R China
Phone: [phone]
Fax: [phone]
Email: contact@swit cc
Website: http://www swit cc

Maintenance
 The Monitor
1 Please keep the signal terminals and the cooling vent away from knife-edge, metal or liquid in
order to avoid short-circuit and damage
2 Please don't try to disassemble any parts of the monitor by yourself, which would probably
damage the monitor and do harm to human body, and it will cause the invalidation of product
warranty
3 Please don't touch the screen with your fingers, which would probably deface the screen
4 Please don't press the screen; the LCD is extremely exquisite and flimsy
 The power
Please use the power adapter provided or recommended by the manufacturer in order to avoid
damage For a third party power adapter, please make sure the voltage range, supplied power, and
polarity of power lead are fit
Please disconnect the power cable under the following situations:
1 If you do not operate this monitor for a period of time;
2 If the power cable or power adaptor is damaged;
3 If the monitor housing is broken
 Working Environment
1 Please don't lay this product on the unstable place
2 Please don't lay this product in hot, cold or wet location
 Cleaning
1 Please clean the screen with dry and downy cloth or special LCD cleanser
2 Please do not press hard when cleaning the screen
3 Please do not use water or other chemical cleanser to clean the screen The chemical may
damage the LCD
4 For first time use, please tear off the factory LCD film To protect the LCD screen, please post the
LCD protection film offered in the package

1. Features
◆
◆◆
◆ High resolution LCD Panel
7-inch, 16:9, 1024×600, 16 77 million colors, 900:1 contrast, and H160°/ V160°viewing angle
◆
◆◆
◆ 3Gbps SDI support
Accept 3G/HD/SD-SDI input
◆
◆◆
◆ Multi Input/Output
Support SDI, HDMI, CVBS input and loop through output
◆
◆◆
◆ Picture-in-Picture
The Picture-in-Picture mode is for cameraman to see the switcher returned CVBS video as an overlay
window on the local camera SDI/HDMI monitoring, which is widely used in EFP system
◆
◆◆
◆ Overlay window adjustable
The position and size of picture-in-picture window are adjustable
◆
◆◆
◆ Multi-functional DB-9 port
To simplify the cable connection, the EFP field monitor provides a Multi-functional DB-9 port, for TALLY
signal input, CVBS returned video input, PIP window on/off switcher input, and DC 6 5-17V power input
◆
◆◆
◆ SDI embedded audio output
Convert SDI embedded audio to analog and output via 3 5mm earphone jack
◆
◆◆
◆ HDMI embedded audio output
Convert HDMI embedded audio to analog and output via 3 5mm earphone jack
◆ Underscan and Overscan
Switch between underscan and overscan mode
◆
◆◆
◆ Safe area
The safe area is offered to mark an area of picture that can be seen on the television screens
◆
◆◆
◆ DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make the effective
image scale full screen on the monitor
◆
◆◆
◆ User definable function keys
There are 2 function keys on the monitor front panel, and users could define the functions to the keys to
achieve shortcut
◆
◆◆
◆ User editable video title
User can edit a video title for the current camera, and the title will display on the top of screen
◆
◆◆
◆ Front and Rear 2-color TALLY light
2 TALLY lights design, to give “live” signals to people in front of the camera, as well as the camera
operator behind
◆
◆◆
◆ Image flip
Rotate the image by 180°

2. Panel Instruction
Front view
⑴ PHONE: Earphone jack, for SDI embedded audio, HDMI embedded audio and analog audio monitoring
⑵ POWER: Power on/off
Connect with power cable, press the “POWER” to switch on the monitor Press again to switch off
Disconnect with power cable if the monitor will not be used for a period of time
⑶ CVBS: Press to switch the input signal to Composite video
⑷ HDMI: Press to switch the input signal to HDMI
⑸ SDI: Press to switch the input signal to SDI
⑹ OVERSCAN: Overscan / Underscan switch
⑺ MENU: Press to enter Menu
⑻ F1: User definable function key 1
⑼ F2: User definable function key 2
⑽ RATIO: 16:9 and 4:3 switch
⑾ ZOOM: Picture Zoom-in
Press “ZOOM” to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in
⑿ DISPLAY: Display current settings
Press “Display” to display safety mark, title and the current input signal information
⒀ OK: Select and Apply
Under menu system, revolve “OK” to adjust settings and press to apply;
and out of menu system, directly revolve “OK” to adjust volume
⒁ TALLY Light: Red and Green 2-color TALLY indicator

Rear view
⑴ DC 12V IN: Connect with the package supplied DC12V 4-pin XLR power adapter
For 3-party power adapter, please ensure the voltage is 6 5-17V, and Pin 1: Negative, Pin 4: Positive
⑵ TALLY Light: Red and Green 2-color TALLY indicator
⑶ CVBS-IN: Composite video input (BNC connector)
⑷ SDI-LOOP: 3G/HD/SD-SDI loop through output (BNC connector)
⑸ SDI-IN: 3G/HD/SD-SDI input (BNC connector)
⑹ HDMI-LOOP: HDMI loop through output
⑺ HDMI-IN: HDMI input
⑻ Multi-functional DB-9 port: See details in Chapter 4, “DB-9 Terminal Description”
⑼ AUDIO L: Stereo audio left channel input (RCA connector)
⑽ AUDIO R: Stereo audio right channel input (RCA connector)
⑾ CVBS-LOOP: Composite video loop through output (BNC connector)
The CVBS-LOOP supports BNC CVBS input or DB-9 CVBS input
Input formats
Input Supported formats
CVBS PAL / NTSC
480I / 576I / 480P / 576P
1080i (60 / 59 94 / 50)
720p (60 / 59 94 / 50)
HDMI
1080p (60 / 59 94 / 50 / 30 / 29 97 / 25 / 24 / 23 98)
SMPTE-425M 1080p (60 / 59 94 / 50)
1080i (60 / 59 94 / 50)
SMPTE-274M 1080p (30 / 29 97 / 25 / 24 / 23 98)
SMPTE-RP211 1080psf (30 / 29 97 / 25 / 24 / 23 98)
SMPTE-296M 720p (60 / 59 94 / 50)
SMPTE-125M 480i (59 94)
SDI
ITU-R BT 656 576i (50)

3. Menu Operation
⑴ Press “MENU” and it will display menu system
⑵ Revolve “OK” to select an item The selected item will be highlighted display
⑶ Press “OK” to enter the selected item
⑷ Under menu system, press “MENU” to back to previous menu
*The menu will automatically save and quit if it remains idle
3.1 PICTURE submenu
The PICTURE submenu includes:
⑴ CONTRAST: 0-100 value adjustment
⑵ BRIGHTNESS: 0-100 value adjustment
⑶ HUE: 0-100 value adjustment
(Only available under CVBS NTSC input)
⑷ SATURATION: 0-100 value adjustment
⑸ SHARPNESS: 0-100 value adjustment
3.2 SYSTEM submenu
The SYSTEM submenu includes:
⑴ RATIO: Aspect ratio “16:9” / “4:3” selection
⑵ SCAN: “UNDERSCAN” / “OVERSCAN” selection
⑶ ZOOM: “OFF”, “ZOOM1” and “ZOOM2” selection
ZOOM1: Canon DSLR scale zoom-in
ZOOM2: Pixel to Pixel zoom-in
⑷ MARKER: Select and set the safe area scale from
80%, 85%, 90% and 95%
⑸ FLIP: Select “ON” to flip the picture by 180°
⑹ RESET: Select “YES” to recover all to factory setting
3.3 OSD submenu
The OSD submenu includes:
⑴ LANGUAGE: Menu language selection
⑵ H-POSITION: Menu horizontal position (0-100)
adjustment, real-time preview and default value: 50
⑶ V-POSITION: Menu vertical position (0-100)
adjustment, real-time preview and default value: 50
⑷ DURATION: Menu timeout setting (5-60)
Set a time (in seconds) in which the menu will
automatically quit if remains idle Default: 15

3.4 TITLE submenu
Revolve "OK" button to select the letters, and press "OK"
to input Select SPACE to input space and DEL to delete
the left letter Max 10 letters are supported
After setting, press "MENU", the system will save data to
current user and quit menu The menu will automatically
save and quit if it remains idle
3.5 DISPLAY submenu
The DISPLAY submenu is to select the items to be
displayed on screen when ‘DISPLAY” button is pressed
Revolve "OK" to turn on/off the items:
⑴ INFO: Including Input format, aspect ratio,
underscan/overscan, zoom status
⑵ MARKER: Safe area
⑶ TITLE: User edited title
⑷ MARKER4:3: The 4:3 scale mark on 16:9 image
(Only available under HD input)
3.6 F KEY submenu
The F KEY Settings Submenu is to define Function Key
F1 and F2 The available function items are:
01- RATIO: Aspect ratio switch
02- SCAN: Underscan / Overscan switch
03- ZOOM: Picture Zoom-in
04- B/W: Color / Black & white switch
05- FLIP: Image flip
06- PIP: PIP mode switch on/off
3.7 PIP submenu
The PIP Settings submenu includes:
⑴ SUB WINDOW: Switch on/off the PIP window
⑵ SIZE: Select the PIP window size from “LARGE”,
“MEDIUM” and “SMALL”
⑶ POSITION: Select the PIP window position from
“CENTER”, “TOP RIGHT”, “BOT RIGHT”, “BOT
LEFT” and “TOP LEFT”
⑷ BORDER: Select the border color of PIP window
from “BLUE” and “BLACK”
Remark: If the SUB WINDOW is off, the SIZE,
POSITION and BORDER are unavailable to adjust

4. DB-9 Terminal Description
The Multi-functional DB-9 port centralized DC power input, CVBS input, picture-in-picture switch on/off and
TALLY light controlling In your build-up EFP system, you can use only one DB-9 cable to input everything,
instead of the complex cable work
The terminal description is as follows:
Terminal 1: Factory firmware burning
Terminal 2: Connect “PIP” with “VGND” to switch on the PIP window, and disconnect to switch off
Terminal 3: Connect “R” with “VGND” to switch on the Red TALLY light, and disconnect to switch off
Terminal 4: Connect “G” with “VGND” to switch on the Green TALLY light, and disconnect to switch off
Terminal 5: Factory firmware burning
Terminal 6: DC input, support 6 5V-17V wide range voltage
(Lower voltage will generate high current, and please use the high quality of DB-9 connector )
Terminal 7: Ground port for DC power and controlling signal
Terminal 8: Composite video input
(The screen will not display if both BNC CVBS-IN and DB-9 CVBS-IN are connected)
Terminal 9: Ground port for CVBS signal
5. Cold Shoe Bracket
The provided monitor bracket supports both cold shoe and screw mount for camera connection
1 For cold shoe: anticlockwise screw the knob to draw the bolt back, slide the cold shoe mount into camera,
and then clockwise adjust the knob to fasten
2 For screw mount: clockwise screw the knob to draw the bolt directly into the screw thread of camera till
fastened
3 Screw the ball head knob into monitors, and lock the ball head
Terminal 1 2 3 4 5 6 7 8 9
Description
PIP G R DC_IN
VGND
CVBS_IN
SGND
① Lock
② Knob
③ Cold shoe mount
④ Screw bolt

6. Specifications
LCD Performance
Size 7 inches
Display area 153 6×90mm
Resolution 1024×RGB×600
Aspect ratio 16:9/4:3
Brightness 400cd
/ m
2
Contrast 900:1
Color 16 77 million colors
Viewing angle Horizontal: 160
° Vertical: 160 °
Video Format
CVBS NTSC
∕ PAL
SMPTE-425M 1080p (60 / 59 94 / 50)
1080i (60 / 59 94 / 50)
SMPTE-274M 1080p (30 / 29 97 / 25 / 24 / 23 98)
SMPTE-RP211 1080psf (30 / 29 97 / 25 / 24 / 23 98)
SMPTE-296M 720p (60 / 59 94 / 50)
SMPTE-125M 480i (59 94)
SDI
ITU-R BT 656 576i (50)
480I / 576I / 480P / 576P
1080i (60 / 59 94 / 50)
720p (60 / 59 94 / 50)
HDMI
1080p (60 / 59 94 / 50 / 30 / 29 97 / 25 / 24 / 23 98)
General
Input voltage DC 6 5V-17V
Power consumption ≤8W
Working temperature 0
℃～ +40 ℃
Working humidity 10%
～ 90%
Storage temperature -15
℃～ +60 ℃
Storage humidity 10%
～ 90%
Dimensions 192×139×48mm
Net weight (main body) 550g
8. Packing List
Simple Package Luxury Package
1 Monitor 1 Monitor
2 User Manual 2 User Manual
3 Power adaptor 3 Power adaptor
4 Power cable 4 Power cable
5 Cold shoe bracket 5 Cold shoe bracket
6 Sun hood 6 Sun hood
7 LCD protection film 7 LCD protection film
8 Mini HDMI to standard HDMI cable
9 D-tap to 4-pin XLR cable
10 Extension arm trestle
11 Carrying case