SWIT S-1071F User manual

Model: S-1071F
7" Broadcast On-camera LCD Monitor
User Manual
Please read this User Manual
throughout before using.

Preface
Congratulations on our purchase of this product. Please read this user manual carefull .
1 ． All internal technologies of this product are protected, including device, software and trademark.
Reproduction in whole or in part without written permission is prohibited.
2 ． All brands and trademarks of SWIT Electronics Co., Ltd. are protected and other relative trademarks
in this user manual are the propert of their respective owners.
3 ． Due to constant effort of product development, SWIT reserves the right to make changes and
improvements to the product described in this manual without prior notice.
4 ． The warrant period of this product is 2 ears, and does not cover the following:
(1) Ph sical damage to the surface of the products, including scratches, cracks or other damage to
the LCD screen or other externall exposed parts;
(2) Misuse, abuse or negligent operation to the product;
(3) The product is disassembled b an one other than an authorized service center.
It is considered normal that the LCD bright dot defects are not to exceed three.
5 ． For an suggestions and requirements on this product, please contact us through phone, fax, Email,
etc.
SWIT Electronics Co., Ltd.
Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone,
Nanjing 210038, P.R.China
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: http://www.swit.cc

Maintenance
 T e Monitor
1. Please keep the signal terminals and the cooling vent awa from knife-edge, metal or liquid in
order to avoid short-circuit and damage.
2. Please don't tr to disassemble an parts of the monitor b ourself, which would probabl
damage the monitor and do harm to human bod , and it will cause the invalidation of product
warrant .
3. Please don't touch the screen with our fingers, which would probabl deface the screen.
4. Please don't press the screen; the LCD is extremel exquisite and flims .
 T e power
Please use the power adapter provided or recommended b the manufacturer in order to avoid
damage. For a third part power adapter, please make sure the voltage range, supplied power, and
polarit of power lead are fit.
Please disconnect the power cable under the following situations:
1. If ou do not operate this monitor for a period of time;
2. If the power cable or power adaptor is damaged;
3. If the monitor housing is broken.
 Working Environment
1. Please don't la this product on the unstable place.
2. Please don't la this product in hot, cold or wet location.
 Cleaning
1. Please clean the screen with dr and down cloth or special LCD cleanser.
2. Please do not press hard when cleaning the screen.
3. Please do not use water or other chemical cleanser to clean the screen. The chemical ma
damage the LCD.
4. For first time use, please tear off the factor LCD film. To protect the LCD screen, please post the
LCD protection film offered in the package.

1. Features
◆
◆◆
◆ New ig resolution 7” LCD Panel
16:9, 1024×600, 16.77 million colors, 900:1
contrast, and H160 ° / V160 ° viewing angle.
◆
◆◆
◆ Multiple inputs
HD/SD-SDI, HDMI and Composite input
◆
◆◆
◆ Loop t roug outputs
Each of the 2 input HD/SD-SDI and HDMI has loop
through output.
◆
◆◆
◆ HDMI converted to SDI output
Supported HDMI formats: 480i / 576i / 720p (50,
59.94, 60) / 1080i (50, 59.94, 60) / 1080P (23.98
24, 25, 29.97, 30), and the output SDI will embed
the audio (48KHz) from HDMI.
◆
◆◆
◆ Waveform (Y, Cb, Cr, R, G, B) and full scale
There are totall 6 kinds of waveform displa ,
available under both SDI and HDMI, to check the
Luminance (Y), Blue-difference (Cb),
Red-difference (Cr), Red (R), Green (G), Blue (B),
and the Y, Cb, Cr can be simultaneousl displa ed,
R, G, B can be simultaneousl displa ed, and each
of the waveforms can be set to full scale displa .
◆
◆◆
◆ Vector scope
The displa ed vector scope pattern is available
under both SDI and HDMI, represents saturation
as distance from the center of the circle, and hue
as the angle, in standard position, around it.
◆
◆◆
◆ Histogram (R, G, B)
The histogram is a bar graph that shows the
distribution of luminance values in the picture.
There’re R, G, B histograms that individuall
displa ed simultaneousl , available under both SDI
and HDMI.
◆
◆◆
◆ 16-c audio meter
Under HDSDI, it displa s 16 channels audio bars,
with mark, and under SDSDI or HDMI, it displa s 2
channels audio bars with mark. The audio bar is
green, and will turn ellow when audio exceeds
-20dB, and turn red when exceeds -10dB.
◆
◆◆
◆ SDI timecode
Under SDI input, it can displa the SMPTE
timecode, which is used extensivel for
s nchronization, and for logging and identif ing
material in recorded media.
◆
◆◆
◆ Peaking focus assist (red/blue switc )
The Peaking focus assist function is to mark the
sharpest edges of the image with red or blue color,
for users to check if the subjects are focused.
◆
◆◆
◆ Zebra stripes
Zebra Stripes are used to check if the image is
over exposed or not b showing black and white
lines on the monitor. It is considered over exposed
when luminance value exceeds 90%.
◆
◆◆
◆ False color
The false color is used to aid in the setting of
camera exposure. Under false color mode, there’s
a false color ke on the bottom of screen for
reference. The over exposed subjects (above 101
IRE) on the monitor will displa as RED, and the
underexposed subjects will displa as BLUE. For
correct exposed subjects, it will displa as green
and pink.
◆
◆◆
◆ Blue Only
Under the Blue Onl Mode, onl the blue pixels are
used to generate the image, because hue and
saturation can be adjusted quicker and more
accuratel .
◆
◆◆
◆ DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio
HDMI and this zoom in mode can make the
effective image scale full screen on the monitor.
◆
◆◆
◆ User definable function keys
There are 3 function ke s on the monitor front
panel, that permit users to define shortcuts for the
various functions.
◆
◆◆
◆ User editable video title
User can edit a video title for the current camera,
and the title will displa on the top of screen.
◆
◆◆
◆ Front and Rear 3-color TALLY lig t
2 TALLY lights design, to give “live” signals to
people in front of the camera, as well as the
camera operator behind.
◆
◆◆
◆ Image Flip
Set image to rotate b 180 °

2. Panel Instruction
Front view
⑴ PHONE: Earphone jack, for SDI embedded audio, HDMI embedded audio monitoring
⑵ POWER: Power on/off
Connect with power cable, press the “POWER” and the power indicator is turned on and the monitor will
be switched on and get into normal working status. Press the “POWER” again, the indicator is turned off
and monitor is switched off.
Disconnect with power cable or batter if the monitor will not be used for a period of time.
⑶ SOURCE: Input signal selection
Press “SOURCE” and revolve the “OK” to select the input video signal.
⑷ F1: User definable function ke 1
⑸ FOCUS: Peaking Focus Assist
Press “FOCUS” once, it will displa the current peaking on/off status. Press “FOCUS” again to switch on
RED line focus assist, switch on BLUE line focus assist, and switch off in turn.
⑹ F.COLOR: False color
Press “F.COLOR” once, it will displa the current false color on/off status. Press “F.COLOR” again to
switch on/off the false color mode.
⑺ DISPLAY: Displa current settings
Press “Displa ” to displa safet mark, title and the current input signal information
⑻ F2: User definable function ke 2
⑼ F3: User definable function ke 3
⑽ WAVEFORM: Displa waveform
Press “WAVEFORM” once, it will displa the waveform menu as:
Revolve “OK” to select a waveform displa mode and turn it on.
The selected waveform will displa on the screen.
⑾ VECTOR: Displa vector scope
Press “VECTOR” to switched on/off the Vector scope
⑿ MENU: Press to enter Menu
⒀
OK: Select and Appl
Under menu s stem, revolve “OK” to adjust settings and press to appl ; and out of menu s stem,
directl revolve “OK” to adjust volume.
⒁ TALLY Lig t: Red, Green and Yellow 3-color TALLY indicator

Rear view
⑴ DC 12V IN: Connect with DC12V 4-pin XLR power adapter. (Pin 1: Negative, Pin 4: Positive)
⑵ TALLY Lig t: Red, Green and Yellow 3-color TALLY indicator
⑶ Battery mount connector:
Connect with SWIT S-7004 series quick release DV mounts, and then mount corresponding DV batteries.
See details in “Optional Batter Mount”.
⑷ SDI OUT: HDMI converted to SDI output (BNC connector)
⑸ SDI-LOOP1: HD/SD-SDI loop through output from SDI-IN1 (BNC connector)
⑹ SDI-LOOP2: HD/SD-SDI loop through output from SDI-IN2 (BNC connector)
⑺ HDMI-IN: HDMI input
⑻ TALLY controlling port (RS-232)
⑼ HDMI-LOOP: HDMI loop through output
⑽ SDI-IN2: HD/SD-SDI input (BNC connector)
⑾ SDI-IN1: HD/SD-SDI input (BNC connector)
⑿ CVBS-IN: Composite video input (BNC connector)
Input formats
Input Supported formats
CVBS PAL / NTSC
480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
720p (60 / 59.94 / 50)
HDMI
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
1080i (60 / 59.94 / 50)
SMPTE-274M 1080p (30 / 29.97 / 25 / 24 / 23.98)
SMPTE-296M 720p (60 / 59.94 / 50)
SMPTE-125M 480i (59.94)
SDI
ITU-R BT.656 576i (50)

3. Menu Operation
⑴ Press “MENU” and it will displa menu s stem
⑵ Revolve “OK” to select an item. The selected item will be highlighted displa .
⑶ Press “OK” to enter the selected item.
⑷ Under menu s stem, press “MENU” to back to previous menu.
*The menu will automaticall save and quit if it remains idle.
3.1 PICTURE submenu
The PICTURE submenu includes:
⑴ CONTRAST: 0-100 value adjustment
⑵ BRIGHTNESS: 0-100 value adjustment
⑶ HUE: 0-100 value adjustment
(Onl available under CVBS NTSC input)
⑷ SATURATION: 0-100 value adjustment
⑸ SHARPNESS: 0-100 value adjustment
3.2 SYSTEM submenu
The SYSTEM submenu includes:
⑴ RATIO: Aspect ratio “16:9” / “4:3” selection
⑵ SCAN: “UNDERSCAN” / “OVERSCAN” selection
⑶ ZOOM: “OFF”, “ZOOM1” and “ZOOM2” selection
ZOOM1: Canon DSLR scale zoom-in
ZOOM2: Pixel to Pixel zoom-in
⑷ MARKER: Select and set the safe area scale from
80%, 85%, 90% and 95%.
⑸ FLIP: Select “ON” to flip the picture b 180°.
⑹ RESET: Select “YES” to recover all to factor setting.
3.3 OSD submenu
The OSD submenu includes:
⑴ LANGUAGE: Menu language selection
⑵ H-POSITION: Menu horizontal position (0-100)
adjustment, real-time preview and default value: 50.
⑶ V-POSITION: Menu vertical position (0-100)
adjustment, real-time preview and default value: 50.
⑷ DURATION: Menu timeout setting (5-60)
Set a time (in seconds) in which the menu will
automaticall quit if remains idle. Default: 15.

3.4 TITLE submenu
Revolve "OK" button to select the letters, and press "OK"
to input. Select SPACE to input space and DEL to delete
the left letter. Max 10 letters are supported.
After setting, press "MENU", the s stem will save data to
current user and quit menu. The menu will automaticall
save and quit if it remains idle.
3.5 DISPLAY submenu
The DISPLAY submenu is to select the items to be
displa ed on screen when ‘DISPLAY” button is pressed.
Revolve "OK" to turn on/off the items:
⑴ INFO: Including Input format, aspect ratio,
underscan/overscan, zoom status
⑵ MARKER: Safe area
⑶ TITLE: User edited title
⑷ MARKER4:3: The 4:3 scale mark on 16:9 image.
(Onl available under HD input)
3.6 F KEY submenu
The F KEY Settings Submenu is to define Function Ke F1, F2 and F3. The available function items are:
01- RATIO: Aspect ratio 16:9 / 4:3 switch
02- SCAN: Underscan / Overscan switch
03- ZOOM: Picture Zoom-in
04- B/W: Color / Black & white switch
05- BLUE ONLY: Blue onl mode switch on/off
06- ZEBRA: Zebra over exposure switch on/off
07- VECTOR: Vector scope switch on/off
08- PATTERN: Internal colorbar switch on/off
09- RGB HIST: R, G, B Histogram switch on/off
10- TIMECODE: SDI timecode displa switch on/off
11- F.COLOR: False color mode switch on/off
12- AUDIO BAR: Audio meter displa switch on/off
13- FOCUS: Peaking focus assist switch on/off,
14- FLIP: Image flip

4. TALLY Lig t Operation
There are front and rear TALLY lights on the monitor, which can displa RED, GREEN and YELLOW signals.
The TALLY light controlling port is the RS232 socket at the rear panel, and terminal description is as follows:
The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting.
The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting.
The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting.
5. Cold S oe Bracket
The provided monitor bracket supports both cold shoe and screw mount for camera connection.
1. For cold shoe: anticlockwise screw the knob to draw the bolt back, slide the cold shoe mount into camera,
and then clockwise adjust the knob to fasten.
2. For screw mount: clockwise screw the knob to draw the bolt directl into the screw thread of camera till
fastened.
3. Screw the ball head knob into monitors, and lock the ball head.
Terminal 1 2 3 4 5 6 7 8 9
Description
Y G R GND
GND
GND
① Lock
② Knob
③ Cold shoe mount
④ Screw bolt

6. Optional Battery Mount
6.1 Battery mount c oice
S-1071F monitor can use Gold mount, V-mount batteries, and DV batteries b connecting with SWIT S-7004
snap-on mount. There’re following t pes of S-7004 for choice:
Model Compatible battery type Recommended SWIT battery
S-7004F SONY L series NP-F770/970 S-8972, S-8970, S-8770
S-7004P Panasonic CGA series D54S/D28S S-8D62
S-7004J JVC BN-V428U S-8428
S-7004C Canon BP series BP-930/945 S-8945, S-8845
S-7004U SONY BP-U series U60/30 S-8U62
S-7004E Canon DSLR, LP-E6 S-8PE6
S-7004B
Panasonic VW-VBG6 S-8BG6
S-7004V JVC BN-VF823 S-8823
Remark: The Gold mount and V-mount are fixed on monitor at factor , not snap-on t pes.
6.2 Installation of S-7004 snap-on DV mount
S-7004 DV mount is snap-on t pe. Please follow the instructions:
(1) Please make sure the power terminals are clean and in well condition before use.
(2) Align the S-7004 slots to the bolts of the monitor rear panel, and press tightl in.
(3) Slide the S-7004 mount down to the bottom.
(4) Fix the S-7004 mount b provided screws on the top side.
(5) Mount the corresponding batter to S-7004 to power the monitor.
Terminal
Slot
Screw hole
Batter
release