SWIT CM-S73H User manual

Model: CM-S73H
7” Full HD High Bright LCD Monitor
User Manual
Please read this user manual throughout before using
Ver：A
SWIT ELECTRONICS CO., LTD.
01

Preface
All internal technologies of this product are protected, including device, software and trademark.
Reproduction in whole or in part without written permission is prohibited.
All brands and trademarks of SWIT Electronics Co., Ltd. are protected and other relative trade-
marks in this user manual are the property of their respective owners.
Due to constant effort of product development, SWIT reserves the right to make changes and
improvements to the product described in this manual without prior notice.
The warranty period of this product is 2 years, and does not cover the following:
⑴ Physical damage to the surface of the products, including scratches, cracks or other damage
to the LCD screen or other externally exposed parts;
⑵ There are no continuous bright or dark spots on the LCD panel;
⑶ Any damage caused by using third-party power adaptors;
⑷ Any damage or breakdown caused by use, maintenance or storage not according to the user manual.
⑸ The product is disassembled by anyone other than an authorized service center.
⑹ Any damage or breakdown not caused by the product design, workmanship, or manufacturing
quality, etc.
＊ Any sales personnel have no rights to provide additional warranty.
For any suggestions and requirements on this product, please contact us through phone, fax,
Email, etc.
SWIT Electronics Co., Ltd.
Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone,
Nanjing 210038, P.R.China
Phone: [phone]
Fax: [phone]
Email: cont[email protected]c
http://www.swit.cc
02

Maintenance
Warning
1. In order to reduce the risk of fire and electrical shock, do not lay this product in rain or damp places.
2. Please keep away from the strong magnetic field; it may cause the noise of the video
and audio signals.
The power
1. Please use the power adapter provided or recommended by the manufacturer in order to
avoid damage.
2. For a third party power adapter, please make sure the voltage range, supplied power,
and polarity of power lead are fit.
3. Please disconnect the power cable under the following situations:
(A). If you do not operate this monitor for a period of time;
(B). If the power cable or power adaptor is damaged;
(C). If the monitor housing is broken.
The monitor
1. Please don't touch the screen with your fingers, which would probably deface the screen.
2. Please don't press the screen; the LCD is extremely exquisite and flimsy.
3. Please don't lay this product on unstable place.
Cleaning
1. Please clean the screen with dry and downy cloth or special LCD cleanser.
2. Please do not press hard when cleaning the screen.
3. Please do not use water or other chemical cleanser to clean the screen.
The chemical may damage the LCD.
Contents
Preface
Maintanance
Contents
Packing list
Introduction
Operation Instruction
Screen display
Zoom-in and mapping
Main Menu
Specification
Trouble shooting
2
2
3
4
4
5
6
7
9
17
18
03

Packing list
Introduction
CM-S73H offers the standard package and luxury package for option.
Monitor
User manual
Warranty card
Cold shoe / Screw ball head
D-tap to lockable DC cable
S-7006（U/F/D/C）/S-7006(A/S)
Articulating arm trestle
AC-DC power adaptor
Power cable
LCD protective film
BNC SDI cable
HDMI cable
Carrying case
Standard package
X 1
X 1
X 1
X 1
X 1
X 1
/
/
/
/
/
/
/
Luxury package
X 1
X 1
X 1
/
X 1
X 1
X 1
X 1
X 1
X 1
X 1
X 1
X 1
CM-S73H adopts TFT LCD panel, with resolution 1920×1200 and wide viewing angle H160°／V120°.
It supports 2 x 3GSDI (Level A/B), 1 x HDMI2.0 (4K display) input. It also supports 1x 3GSDI, 1 x HDMI
and 1 x analog audio loop through output.
Features:
3000nit super high brightness
Support HDMI 4K display
Camera Log conversion
Support 3DLut cube
Support multiple Aspect Ratio and scan modes
Support multiple Marker selection (Marker, Safety Area)
Powerful audio and video analysis functions
Support multiple functions user-defined (Source ID, function keys)
Multiple power supply methods to meet different requirements
USB firmware upgrade
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
04

Operation Instruction
⑴ Button
Source: Signal selection button（HDMI、SDI1、SDI2）
User definable function keys（F1～F3）
User can set F1～F3 keys to corresponding function for quick operation according to their needs.
For example：User can set F1 to “Focus Assistant”, and press F1 to directly switch the focus assistant
parameter, the sequence is “Red→Blue→Off”.
Quick function keys support multi definition, for details please refer to “4.Function key settings” in
the “MENU” section.
BACKLIGHT: Quickly adjust the brightness level. There are four levels of “Off”, “Low”, “Medium” and
“High” optional. The corresponding brightness of “Low”, “Medium” and “High” are 380nit, 900 nit
and 3000 nit.
Note: When set to “Off”, the user can adjust the “Backlight” parameter value under “Picture”
submenu according to the requirements.
DISPLAY：Press “DISPLAY” to turn on or turn off relevant status information, audio and video
analysis assistant Pattern.
When main menu is activated, press “DISPLAY” to quit menu.
⑵ Main menu settings
When no menu is opened, user can directly press the knob, and open the main menu on the left top
of the screen;
Rotate the knob, select corresponding submenu; the corresponding item is highlighted in yellow;
Press the knob, enter the submenu;
Rotate the knob to select items; the corresponding item is highlighted in yellow;
Press the knob, the parameter of the item is highlighted in yellow;
Rotate the knob to select the parameter and press to save the settings.
⑶ POWER: Power on/off
⑷ PHONE：3.5mm earphone socket, for SDI/HDMI embedded audio and analog audio monitoring.
⑸ DC 6.5-17V IN: Round head DC power supply interface (Outer: Negative, Inner: Positive)
⑹ Silent fan
⑺ Battery mount connector
It is powered by DV batteries. When the power supply voltage is 7.2V, the maximum brightness can
reach to 2000 nit.
05
(1) (2) (3) (4) (6) (7) (8) (9)
(10)
(5)

⑻ Video Signal Interface
HDMI-IN：HDMI input (HDMI-A connector)
HDMI-OUT：HDMI output (HDMI-A connector)
SDI-IN1：3G/HD/SD SDI input (BNC connector)
SDI-IN2：3G/HD/SD SDI input (BNC connector)
SDI-OUT：3G/HD/SD SDI output (BNC connector), the monitor choose fixed SDI-IN1 signal to loop
output.
⑼ External interface control
GPI：GPI control socket
USB：For firmware upgrade
⑽ Speaker
Monitor HDMI, SDI embedded audio and analog audio monitoring. (when connecting 3.5mm audio
output, the speaker is off).
Screen display
⑴ Time code（SDI）
Under SDI input, it can display Time code. If no Time code information is detected, it will be displayed as
“TC: UNLOCKED”.
User can set function keys F1～F3 as “Time code” to turn on or off this function
⑵、UMD
Display the source title. Set up the UMD under ‘UMD” submenu.
⑶、AFD（SDI）
User can set function keys F1～F3 as “AFD” to turn on or off this function. If no relevant information is
detected, it will be displayed as “AFD: UNLOCKED”.
⑷、Soft Tally
When connected with TALLY control devices and set TALLY port in GPI, the screen will display soft TALLY
signal, flashing in Red, Green or Yellow. Refer to “Main Menu—5. GPI”.
⑸、Audio
Monitor the audio information. User can set function Keys F1～F3 as “Audio” to turn on or off this
function
The relevant parameters like position, audio channels and blending, etc can be changed under “Audio”
submenu.
06
CAMERA 1
TC：00:15:13:07
-09
-20
-48
12345 6 7 8
9
1011 12
13141516
L -20DB 01CH R -22DB 01CH
(1)
(2)
(3)
(4)
(5)

Zoom-in and mapping
Set “Zoom-in” to function keys, and enable zoom-in mode, the OSD displays as above.
1、 Zoom-in steps operation
Scroll the menu key up and down you can quickly zoom in the video by the following rates: 1.2x, 1.5x,
1.8x, 2.0x, 2.4x, 2.6x, 2.8x, 3.0x, without black waiting. The zoom-in indication window is displayed on
bottom right of the screen.
Press the menu key to switch to Left/Right mapping function, and press again to switch to Up/Down
mapping, and so on.
2、 Left and Right mapping
Press Menu key, the button is highlighted. Scroll the Menu key up and down to move the video left
and right.
3、 Up and Down mapping
Press Menu key again, the button is highlighted. Scroll the Menu key up and down to move the video
up and down.
4、 Peaking precision adjust
Press Menu key again, the peaking precision number is highlighted. Scroll the Menu key up and down
to adjust the peaking focus assist precision from 0-9.
5、 Mapping indication window
Under zoom-in mode, the mapping indication window is displayed on bottom right of the screen, and
indicates the zoom-in rate, up/down/left/right position.
07
0
1.2 X
0
Zoom-in steps
Left/Right mapping
Up/Down mapping
Peaking precision
Mapping indition

Introduction of audio and video functions
16-ch embedded audio meters
Under 3G/HD/SD SDI, it displays 16 channels embedded audio meters. Under HDMI, it displays 2
channels embedded audio meters. The audio meter is green, and will turn yellow when audio
exceeds -20dB, and turn red when audio exceeds -9dB.
Audio alarm
If the embedded audio value is too low or no embedded audio, it will display “MUTE” or
“UNLOCKED” in the audio bar.
Time code（SDI）
Under SDI input, it can display the SMPTE time code (VITC1, VITC2 or LTC) on the top of the screen,
which is used extensively for synchronization, and for logging and identifying material in recorded
media. If no Time code information is detected, it will be displayed as “UNLOCKED”.
Internal Color Bar
Under SDI and HDMI input, it has 100% internal color bar which helps to analyze the monitor color
and adjust the display parameter.
User can set function Keys F1～F3 or GPI pins as “color bar” to turn on or off this function.
Peaking focus assist (red/blue switch)
The Peaking focus assist function is to mark the sharpest edges of the image with red or blue color
under SDI and HDMI input, for users to check if the subjects are focused.
User can set function Keys F1～F3 or GPI pins as “Focus Assist” to turn on or off this function.
Zebra stripes
Zebra Stripes are used to check if the image is over exposed or not by showing black and white lines
on the monitor. It is considered over exposed when luminance value exceeds 90%.
User can set function Keys F1～F3 or GPI pins as “Zebra” to turn on or off this function.
Freeze Frame
The freeze frame is to capture and display the current broadcast frame.
User can set function Keys F1～F3 or GPI pins as “Freeze Frame” to turn on or off this function
R/G/B/Mono
R/G/B/Mono is to display only the blue/red/green primary signal or the luminance signal only so as
to monitor the image noise.
User can set function Keys F1～F3 or GPI pins as “R/G/B/Mono” to turn on or off this function.
False Color
The false color is used to aid in the setting of camera exposure. Under false color mode, there’s a
color chart on the bottom of screen for reference. The color from the dark to the bright will be
displayed as blue, cyan, green, yellow, orange and red in a consecutive way. User can set function
Keys F1～F3 or GPI pins as “False color” to turn on or off this function.
AFD（SDI）
It is the abbreviation of active format description. AFD is to display the SDI embedded AFD
information graphically on the screen.
H/V Delay (SDI)
Under SDI input, H/V Delay can be used to display line/field blanking signal, and to observe the
horizontal and vertical synchronous signal.
Image flip
Horizontal, vertical, horizontal and vertical two-way image flip function.
08

Main menu
CM-S73H has OSD to adjust the parameters and settings, for example: Picture, color temp., function
keys, etc.
1. Press “MENU” button, the main menu will popup from the left top of the screen. The selected main
menu highlights in yellow.
2. Revolve “MENU” to select submenu, the selected submenu highlights in yellow, press “MENU” to
apply and enter into the selected submenu’s items.
3. Revolve “MENU” to select the item which needed to adjust, press “MENU”, the selected item and
its parameters will be highlighted in yellow.
4. Revolve “MENU” to change the selected item’s parameter, press “MENU” to apply and save the
settings.
5. Revolve “MENU” to select “Exit”, press “MENU” to quit submenu. Select “Exit & Status” under the
Main Menu and press to quit Main Menu.
Notice:
＊ The items in gray can not be set up.
＊ If there is no operation under the set time, the menu will automatically save settings and quit.
＊ If the key inhabit function is turned on, except key inhibit function, all other items are in grey.
Please turn off the key inhibit function to adjust the items.
Main Menu
Exit&Status
Picture
Color Temp
Funcon Key
GPI
UMD
Marker
Audio
Vector
Waveform
Display
System
OSD
Key Inhibit
＞
＞
＞
＞
＞
＞
＞
＞
＞
＞
＞
＞
＞
＞
Status
HDMI XXX
User Profile XX
Color Temp XXXX
Scan Mode XXX
Freeze Frame XXX
Odd/Even Frame XXX
F1 XXX
F2 XXX
F3 XXX
F4 XXX
F5 XXX
System Version XXX
Main Menu
Exit&Status
Picture
Color Temp
Funcon Key
GPI
UMD
Marker
Audio
Vector
Waveform
Display
System
OSD
Key Inhibit
＞
＞
＞
＞
＞
＞
＞
＞
＞
＞
＞
＞
＞
＞
Marker
Exit
Marker XX
Marker Select 15:9
Safety Area XXX
Fit Marker XXX
Center Marker XXX
Marker Color XXX
Marker Outside XXX
09

Submenu introduction（the default values are marked with underline ）
1. Exit & Status
Displays the current status, the details are as down below:
*1 Display the current video signal and format
*2 Display the current function keys setup
2. Picture
To adjust picture parameters
3. Color Temp
To select different color temperature or setup user-defined color parameters.
* Only “Color Temp” is set to “User”, the Red/Blue/Green Gain or Red/Blue/Green Bias can be adjusted.
Exit&Status HDMI
User Profile
Color Temp
Scan Mode
Freeze Frame
Odd/Even Frame
F1
F2
F3
F4
Factory
6500K
Normal
Off
Off
Time code
Focus Assist
Zebra
Max Backlight
F5 Freeze Frame
F6 Scan Mode
System Version VXXX-XX
1080p@50Hz
*1
*2
Picture Exit
Contrast
Brightness
Saturaon
Sharpness
Tint
Backlight
0-100,50
0-100,50
0-100,50
50
50
0-100,50
Aspect Rao Auto,4:3,16:9,Full
Scan Mode Normal,Nave
Zoom Mode Off,On
Scaling Posion Center
Flip Mode Off,H Flip,V Flip,H/V Flip
Freeze Frame Off,On
Color Temp Exit
Color Temp
Red Gain
Green Gain
Blue Gain
Red Bias
Green Bias
6500K,5600K,9300K,3200K,User
0-255,128
0-255,128
0-255,128
0-255,128
0-255,128
Blue Bias 0-255,128
Gamma 2.2,2.4,2.6
10

4、 Function key
To define the F1～F3 function keys
*1 Function keys F1-F3 can be set as the down below functions:
Time code, Zebra, Audio Bar, False Color, AFD, H/V Delay, R/G/B/Mono, Marker, Color Bar, UMD, Audio
Alarm, Focus Assist, Aspect Ratio, Scan Mode, Zoom Mode, Mute, Freeze Frame, Flip Mode, Color Temp.
For example: Set F3 to “R/G/B/Mono” under “Function key” submenu. User can press F3 on the front
panel to adjust the parameters of “R/G/B/Mono”, and the “R/G/B/Mono” will change and follow the
sequence: Blue Only →Red Only →Green Only →Mono →Off.
5、 GPI
User can set GPI pins 1-4 to relevant functions to turn on or off this function.
*1 When “GPI control” is set to “On”, the monitor can be operated through external GPI control unit.
*2 The GPI pins can be set to the down below functions:
Red Tally, Green Tally, Yellow Tally, Aspect Ratio, Scan Mode, Zoom Mode, Mute, Freeze Frame, Flip Mode,
Color Temp, Time code, Zebra, Vector, Audio Bar, False Color, AFD, H/V Delay, R/G/B/Mono, Marker, Color
Bar, UMD, Audio Alarm, Max backlight, Focus Assist.
When connecting the GPI pin with ground, the setted function will be turned on, and goes out when
disconnecting.
Funcon Key Exit
F1
F2
F3
F4
Time Code
Focus Assist
Zebra
Max Backlight
F5 Freeze Frame
F6 Scan Mode
*1
GPI Exit
GPI Control
1Pin
2Pin
3Pin
4Pin
5Pin
6Pin
Off,On
Red Tally
Green Tally
Audio Alarm
UMD
Color Temp
Mute
*1
*2
Example 1: Under “GPI ” submenu, set “GPI control” to “On”, set “2 Pin”
to “Red Tally”, when the pin 2 of the extenal GPI control unit is connected
with ground, the Tally light will display on the front panel which will
flashes in red around every second. When disconnected, the monitor will
not display tally light information.
Example 2: Under “GPI ” submenu, set “GPI control” to “On”, set “4 Pin”
to “Scan Mode”, when the pin 4 of the extenal GPI control unit is connected
with ground, the Scan mode will change and follow the sequence: “Normal” →“Overscan”→“Native” .
11
Pin
Pin
GPI
GPI
1
GPI_1 GPI_2
6
NC
NC
NC GND
5
GPI_4
2 3
7
4
GPI_3
8

Set “UMD”:
⑴ Select “Source ID”
(2) The underline flashes as a reminder on the bottom of the first letter. Revolve "MENU" to select the
letters; the letter will follow the sequence of the down below if clockwise revolved:
(3) Press “MENU” to save the current settings letter and then start to set the next letter.
⑷ Repeat step (2) and step (3), max 8 letters are supported.
⑸ Press “Exit” to quit and save the settings.
7. Marker
*1 When “Fit Marker” is “Off”, the size of safety area is benchmarked against the actual display
screen, accounting for 80% ~ 95% of actual display screen. When “Fit Marker” is “On”, the size of
safety area is benchmarked against the area inside the scales marker, accounting for 80% ~ 95%
of the area inside the scales marker.
Example:
6、UMD UMD Exit
RS485 Address
Posion
Display Type
Baud Rate
Parity
Serial Port
1
Size Normal
Top,Boom
Color Red,White,Black,Blue,Green,Yellow
Source ID
38400
Even
RS485
Source ID CAMERA 1
Marker Exit
Marker
Marker Select
Safety Area
Fit Marker
Center Marker
Marker Color
Marker Outside
Off,4:3,13:9,14:9,15:9,16:9,1.85:1,2.35:1
Off,80%,85%,90%,93%,95%
Off,On
Off,On
White,Red,Green,Blue,Black,Gray
Off,On
Off,Gray,Black
*1
Aspect ratio: 4:3 Safety Area: 85%
Center Marker: On Fit Marker: Off
Aspect ratio: 4:3 Safety Area: 85%
Center Marker: Off Fit Marker: On
Safety Area Marker Outside
Center Marker Marker Select
12

8. Audio
*1 When “Bar Frame” is set to “Off”, only the audio meter will be displayed.
When “Bar Frame” is set to “On”, frame and real-time audio value will be displayed.
*2 Select Channel
Under HDMI signal, channel1-2 can be selected.
Under SDI signal, channel 1-2, 1-8 and 1-16 can be selected.
*3 When “Audio Alarm” is set to “On”, if no embedded audio is detected, the audio bar will display
“UNLOCKED”. If the audio value is too low, the audio bar will display “MUTE”.
*4 Audio channels can be selected to output according to the requirements.
When the current “Select Channel” is set to “Channel1-2”, the left channel and right channel
output can be selected from Channel1 or channel 2.
When the current “Select Channel” is set to “Channel1-8”, the left channel and right channel
output can be selected from Channel1 to channel 8.
When the current “Select Channel” is set to “Channel1-16”, the left channel and right channel
output can be selected from Channel1 to channel 16.
In audio bar, the left channel information will be in green, and the right channel information will
be in red.
Channel 1～2 Channel 1～8 Channel 1～16
Audio Exit
Audio Bar
Bar Frame
Bar Posion
Bar Blending
Select Channel
Audio Alarm
Le Channel
Right Channel
Off,On
Off,On
Top Right,Boom Le,Boom Right,Top Le
Low,Off,High
Channel 1-2,1-8,1-16
Off,On
CH1-CH16,CH1
CH1-CH16,CH2
*1
*2
*3
*4
13

9. Display
10. System
*1 Source Scan
When set to “On”, after turn on the monitor, the signal will be inspected and follow the sequence
of “SDI1→SDI2→HDMI”.
For example: if channel is selected to SDI1, SDI1-IN has no input, and HDMI has input. When turn
on the monitor, after automatic inspection, SDI1 has no recognized signal, and HDMI has
recognized signal, then the input signal will be HDMI.
When set to “Off”, update model will not be supported.
*2 Logo
When powered on, the screen will display SWIT logo.
*3.*4 Update Driver/ Kernel
⑴ Open the power supply, plug the U disk with upgrading programma into the USB port on the
rear of the monitor；
⑵ Press “MENU” rotary knob, open the main menu, enter the “system” submenu, select
“Driver/Kernel”；
Display Exit
Waveform
Audio Bar
Vector
Zebra
Focus Assist
Time Code
Histogram
Off
Off,On
Off
Off,On
Off,On
Off
Off,On
Off,On
Off,On
Off,On
Off,On
Off,Blue,Red
False Color
AFD
H/V Delay
R/G/B/Mono
Color Bar
Marker
UMD
Off,On
Off,Blue Only,Red Only,Green Only,Mono
System Exit
Recall Profile
Save Profile
EDID Switch
Logo
Idle Duraon
Update Driver
Factory,User1,User2,User3
User1,User2,User3
EDID 2.0,EDID 1.4
Source Scan On,Off
Odd/Even Frame Off
On,Off
Green Mode
Black Backlight
2Hours
No,Yse
Update Kernel No,Yes
*1
*3
*2
*4
⑶ Set the parameter to “Yes”, and press “MENU” rotary knob
to begin upgrading；
⑷ While upgrading, there will be a prograss bar displaying on
the screen (Note: Do not power off when upgrading）；
⑸ After upgraded, the monitor will automatically reboot.
14

*1 Camera Log conversion
When shooting with Log mode of the camera, you can select the corresponding Log conversion LUT,
to convert the log mode video to standard ITU Rec.709 mode to monitor. A ”User-Log” is provided for
user defined LUT converting to Rec.709.
*2 HDR
CM-S73H supports three HDR modes: PQ_709、HLG_709、S-Log3.
*3 Color measurement
Set the Color measurement parameter to “On” before color calibration, make sure the parameter set
to “Off” after color calibration. When reboot, the Color measurement parameter automatically set to
“Off”.
*4 Import 3DLUT cube file
⑴ Use a color analysis instrument and calibration software, and set to 6500K, Gamma2.4 for color
calibration, this will generate a correct cube file (recommended Konica Minolta color analyzer
CA-310 and Spectracal CalMAN software);
⑵ Rename the cube file to “3DLut.cube” (attention to the cap lettters) , and copy to USB stick;
⑶ Insert USB stick to the rear panel of the monitor. Select Operate Menu ‒ Color Measurement ‒
“Import” ‒ “3DLut.cube” ‒ “Yes” to import
⑷ Import user needed Log Lut, User-log file and 1DLut by USB stick.
*5 Reset to factory cubes
For any wrong cubes imported that caused wrong display colors, you can reset the cubes to factory
cubes here.
Color Measure
Color Measurement
Exit
Log Mode
1DLut
Off,J-Log1,Log-C,S-Log2,C-Log,
V-Log,RedlogFilm,User-Log
Default,User1,User2
HDR Off,PQ_709,HLG_709,S-Log3
Off,On
Import 3DLut.cube,J-Log1.cube,Log-C.cube,
S-Log2.cube,S-Log3.cube,C-Log.cube,
V-Log.cube,RedLogFilm.cube,
User-Log.cube,PQ_709.cube,HLG_709.cube,
1DLutUser1.csv,1DLutUser2.csv
3DLut.cube,J-Log1.cube,Log-C.cube,
S-Log2.cube,S-Log3.cube,C-Log.cube,
V-Log.cube,RedLogFilm.cube,User-Log.cube,
PQ_709.cube,HLG_709.cube
Reset
*1
*2
*3
*4
11. Color Measure
15

12. OSD
13. Key Inhibit
When the “Key inhibit” is set to “on”, there is no response when all the buttons except “MENU” is
pressed, the sreen will be displayed as “ Key Inhibit”.
User can set “Key inhibit” to off under the “Key inhibit” submenu, restore the function of all keys.
OSD Exit
OSD Language
OSD Blending
OSD Duraon
Tally-R Brightness
Tally-G Brightness
English,Chinese
Low,Medium,High,Off
10Sec,15Sec,30Sec,60Sec
OSD Zoom Off
Key Led Brightness Low,Medium,High,Off
High
High
So-Tally Posion
So-Tally Blinking
Top
On
Key Inhibit Exit
Key Inhibit Off,On
16

Specification
*1 Only when the power supply voltage ≥12V，the maximum brightness can reach to 3000 nit.
LCD Performance
Size
Display area
Resolution
Color
Aspect ratio
Brightness*1
Contrast
Viewing angle
7 inch
151.2×94.5 mm
1920×RGB×1200
8 bit
16:9／4:3
3000 cd／m2
1200:1
Horizontal / Vertical: 160°／160°
Input/Output
Input
Output
HDMI×1
BNC×2
USB×1
HDMI×1
BNC×1
3.5mm×1
HDMI input
3G/HD/SD-SDI input
HDMI output
3G/HD/SD-SDI loop output
SDI/HDMI embedded audio output
Video format
HDMI
SDI
SMPTE-425M-A/B
SMPTE-274M
SMPTE-RP211
SMPTE-296M
SMPTE-125M
ITU-R BT.656
SMPTE-2048-2
1080p（60／59.94／50）
1080i（60／59.94／50）
1080p（30／29.97／25／24／23.98）
1080psf（30／29.97／25／24／23.98）
720p（60／59.94／50）
480i（59.94）
576i（50）
2048×1080p（23.98／24／25／29.97／30／50／59.94／60）
2048×1080i（50／59.94／60）
480i／576i／480p／576p
1080i（60／59.94／50）
720p（60／59.94／50）
1080p（60／59.94／50／30／29.97／25／24／23.98）
1080psf（30／29.97／25／24／23.98）
4096X2160（60／50／30／25／24）
3840X2160（60／50／30／25／24）
Input voltage
Power consumption
Working temperature
Working humidity
Storage temperature
Storage humidity
Dimensions
Net weight（main body）
DC／Battery：6.5V～17V
≤26W
-10℃～+50℃
10%～90%
﹣15℃～﹢60℃
10%～90%
187×137×41mm
500 g
17

Trouble-shooting
symptom
No display
Image or
color abnormal
No audio output
The power is not turned on
Unstable power voltage
BNC or HDMI cable loose
contact or not correctly
connected
The attached battery is
no power
Using DIY power supply but
the polarity is reversed
Possible causes Solution
Please check if the power is connected, and then
press “POWER” button to turn on the monitor
Reconnect to power supply
Check and correctly connect the BNC or HDMI cable
Change battery
Refer to the provided power supply,
reconnect the power.
Bad contact of BNC
or HDMI cable
Video signal has Interference
Improper adjustment of the
color parameters
Distortion of the image
Set to Red/Green/Blue only
or Mono
Turn on the “Focus Assist”
function
Turn on the “False Color”
function
Signal can not correctly
recognize color space,
wrong set of HDMI color space.
Change cable
Remove the interference source(s)
Adjust the “Recall profile” to “Default”
under “System” submenu
Reset the Aspect ratio
Turn the Blue only/ Red Only/ Green Only/Mono
off under R/G/B/Mono submenu
Turn off the “Focus Assist” function
Turn off the “False Color” function
Set to the correct color space mode
Set to Mute
Bad contact of signal cable
Turn off MUTE or revolve “MENU/ENTER”
to adjust the volume
Connect to the correct input socket
18

SWIT Electronics Co., Ltd.
Add: 10 Hengtong Road, Xin'gang, Nanjing Economic and
Technological Development Zone, Nanjing 210038, P.R.China
Tel: [phone] Email: contac[email protected]c
SWIT Electronics Europe GmbH
Add: Hochstr. 17, 47228 Duisburg, Germany
Tel: [phone] Email: [e-mail]
SWIT Electronics America, Inc
Add: 3350 Scott Boulevard 61-02, Santa Clara, CA 95054, USA
Tel: [phone]-SWIT(7948) Email: [email protected]
19