SYDELL 780 User manual

#780 HYDRAULIC STAND
ASSEMBLY INSTRUCTIONS
PARTS LIST
SET OUT ALL THE PARTS AND MAKE SURE YOU HAVE RECEIVED ALL THE PARTS BEFORE
ASSEMBLING
1-DECK 1-WELDED LEGS 2-LEGS 1-JACK PLATE 1-AXLE
1-NECK 1-JACK 1-JACK 2-WHEELS 1-#733 1-HYDRAULIC 3-STAR
SLEEVE SLEEVE HANDLE JACK KNOBS
BOLTS NUTS WASHERS
2-1/2” X 5” GR8 6-1/2” LOCK NUTS 10-1/2” WASHERS
4-1/2”X 2 ¾”GR8 1-7/16” LOCK NUTS
1-7/16”X 2 ½”
1-#731-L 1-HOSE CLAMP

#780-HYDRAULIC STAND
ASSEMBLY INSTRUCTIONS
STEPS 1-5
Do not tighten any bolts until after Step #5
STEP #1
Attach the (2) legs to the welded legs using (2) ½” x 2 ¾” gold bolt, (2) ½” flat washers, and (2) ½”
lock nuts. (See Diagram A)
Note: Do not tighten bolts at this time. In addition notice the distance between the legs in the back to
make sure you have the (2) legs in the right direction.
STEP #2
Attach the (2) wheels to the (2) legs and the jack plate using (2) ½” x 4 ½” bolts, (6) ½” flat washers,
and (2) ½” lock nuts. (See Diagram B)
STEP #3
Slide the jack sleeve into the hydraulic jack as shown (See Diagram C)
Diagram A Diagram B Diagram C
Note distance between the back of
the legs and welded legs
Note two holes on leg should be towards the wheels
(on opposite end (not pictured).
STEP #1
STEP #1
STEP #2
STEP #3
STEP #4
STEP #5
Bolt Head
LEG
WELDED
LEG
BACK
1/2" LOCK
NUT
WELDED LEG
1/2"
WASHER
1/2" x 2 3/4"
BOLT
LEG
1/2"
WASHER
1/2" LOCK
NUT
WHEEL
1/2" X 5"
BOLT
JACK
PLATE
LEG

#780-HYDRAULIC STAND
ASSEMBLY INSTRUCTIONS
STEP #4
Attach the jack sleeve to the welded legs using (1) 7/16” x 2 ½” bolt, and (1) 7/16” lock nut. Next lay
the hydraulic jack into the jack plate and attach it using the hose clamp. (See Diagram D and E)
STEP #5
Slide the axel through both of the legs. Make sure there is even spacing on each side. (See Diagram F)
Tighten all bolts, then back of ½ turn so parts can move freely
Diagram D Diagram E Diagram F
Note: The bolt head needs to be on Do not over tighten hose clamp
the left side as pictured as the jack needs to be able to
move slightly.
STEPS 6-10
STEP #6
Slide the deck from the front to the back making sure that
the axel slides into the track. Next attach the front of the
deck to the legs using (2) ½” x 2 ¾” gold bolt, (2) ½”
flat washers and (2) ½” lock nuts. (See Diagram G)
Tighten bolts and back off ½ turn, so parts can move freely
STEP #7
Slide the neck sleeve into the deck and tighten (2) set knobs
(See Diagram G)
STEP #8
Slide the #733 neck reach into the neck sleeve and tighten
set knob.
STEP #9
Assemble the chain kit onto the #731 headpiece using the
enclosed instructions. Then slide the #731 headpiece into the
#733 neck reach and tighten set knob.
Diagram G
STEP #6
STEP #7
STEP #8
STEP #9
Bolt Head
SET KNOB
NECK
SELEVE
TRACK
SET KNOB
HOSE
CLAMP
LEG
DECK
1/2"
WASHER
1/2" x 2 3/4"
BOLT DECK
LEG
DECK
WELDED LEG
1/2" LOCK
NUT

BOLT HEAD