Symmons Dia 3503-H321-V-CYL-B-TRM Manual

1Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3047 REV 0 01/29/2014
3503-H321-V-CYL-B-TRM, 3505-H321-V-CYL-B-TRM,
3506-H321-V-CYL-B-TRM
Dia™Trim Series
Operation & Maintenance Manual
Model Numbers Specifications
3503-H321-V-CYL-B-TRM Dia Hand Shower Trim
3505-H321-V-CYL-B-TRM Dia Shower/Hand Shower
Trim
3506-H321-V-CYL-B-TRM Dia Tub/Shower Trim
with Hand Shower
Tub/shower trim with hand shower and lever handle
includes wall connection, 30" slide bar, non-diverter tub
spout (067), in-line vacuum breaker, exible metal hose,
1 mode hand shower (EF-100) and 1 mode showerhead
(352SH) with standard 2.5 gpm (9.5 L/min) ow restrictor.
Shower trim with hand shower includes all of the above
less non-diverter tub spout. Dia shower trim includes
all of the above less non-diverter tub spout and 1 mode
showerhead.
Modifications Compliance
-1.5 1.5 gpm (5.7 L/min) flow restrictor
-2.0 2.0 gpm (7.6 L/min) flow restrictor
Delete Chrome plastic escutcheon on valve with
Suffix B color graphics/indicators in place of
standard brass escutcheon
-LP Loop handle
-LR Lever handle
-SS Slip spout on any tub and shower unit
-STN Satin nickel finish
-ASME A112.18.1/CSA B125.1
Warranty
Limited Lifetime - to the original end purchaser in
consumer installations.
5 Years - for commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Note: Append appropriate -sufx to model number.
c

2Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3047 REV 0 01/29/2014
3503-H321-V-CYL-B-TRM, 3505-H321-V-CYL-B-TRM,
3506-H321-V-CYL-B-TRM
Dia™Trim Series
Operation & Maintenance Manual
Dimensions
Notes:
1) All dimensions measured from nominal rough-in (see S as reference).
2) Dimensions are subject to change without notice.
PP
A
D
D
C
C
I
I
HH
L
L
M
M
N
N
G
G
B
B
E
E
K
K
J
J
O
O
S
S
T
T
R
R
Q
Q
F
F
Floor
Floor
Measurements
A Ø 2 1/2”, 64 mm
B 6 3/4”, 171 mm
C 2 1/8”, 54 mm
D 5 1/2”, 140 mm
E
1/2” I.P.S. thread must
be recessed 1/4” from
nished wall
F 6”, 152 mm right or left
G 77”, 1956 mm
H Ø 7 3/4”, 197 mm
I Ø 5”, 127 mm
J 8”, 203 mm
K 4 3/4”, 121 mm
L Ø 2 1/2”, 64 mm
M 32”, 813 mm
N 12”, 305 mm
O 3”, 76 mm
P 2 7/8”, 73 mm
Q 12” - 14 NPT
R 5 1/4”, 133 mm
SRough-in
2 3/8” ± 1/2", 60 mm ± 13 mm
T 7”, 178 mm

3Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3047 REV 0 01/29/2014
3503-H321-V-CYL-B-TRM, 3505-H321-V-CYL-B-TRM,
3506-H321-V-CYL-B-TRM
Dia™Trim Series
Operation & Maintenance Manual
Parts Breakdown
E
D
I
GH
J
K
M
M
K
NH
O
P
Q
R
S
T
A
B
F
L
L
C
Replacement Parts
Item Description Part Number
D
E
Shower Arm
Flange 300S
F 1 Mode Showerhead 352SH
G
H
I
M
Diverter Escutcheon
Screws
Small Mounting Plate
Dome Cover
Diverter Escutcheon
Kit
RTS-041
H
M
N
O
Screws
Dome Cover
Escutcheon
Large Mounting Plate
Escutcheon Kit
RTS-009 (Brass)
RTS-010 (Plastic)
KHandle
Assembly T-242A
M Dome Cover T-19/20
T Tub Spout 067
Notes:
1) Append -STN to part number for satin nickel nish.
2) Append -1.5 or -2.0 to showerhead or hand shower
for low ow.
Required for Installation
Adjustable Wrench
Phillips Head crewdriver
Allen Wrench (3/16”)
Teon Tape
Power Drill

4Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3047 REV 0 01/29/2014
3503-H321-V-CYL-B-TRM, 3505-H321-V-CYL-B-TRM,
3506-H321-V-CYL-B-TRM
Dia™Trim Series
Operation & Maintenance Manual
Installation
Note:
For rough-in installation, please
see valve body installation guides.
1) Install small plastic mounting plate
(I) to diverter valve (3506 diverter
valve = 4-460E-BODY, 3505
diverter valve = 4-458E-BODY)
and large plastic mounting plate
(O) to shower valve (4000-BODY).
Secure each with two screws (H).
2) Attach diverter escutcheon (G) to
small plastic mounting plate (I).
Note: Tabs should snap into place.
3) Attach shower escutcheon (N) to
large plastic mounting plate (O).
Note: Tabs should snap into place.
4) Install dome covers (M) to valves
by turning clockwise.
5) Install diverter handle (3505 and
3506 only) (K) and shower handle
(K) to valves. Secure handles by
tightening Allen screws (L).
Note: Handles should be facing the
6 o'clock position.
6) Install tub spout (T) to stub out
pipe. Turn clockwise to secure.
1
1
2
I
H
H
O
G
I
NO
1
1
2
M
M
1
1
2
K
KL
L
1
2
T

5Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3047 REV 0 01/29/2014
3503-H321-V-CYL-B-TRM, 3505-H321-V-CYL-B-TRM,
3506-H321-V-CYL-B-TRM
Dia™Trim Series
Operation & Maintenance Manual
Installation
7a) Dry Wall Option: R emove upper
and lower caps (P) from 30" slide
bar brackets. Place 30" slide bar
(R) into desired position. Using
brackets as a guide, carefully drill
3/16" holes into wall. Remove
30" slide bar and install anchors.
Notes: Make sure that 30" slide
bar holes and bracket holes are
aligned before drilling. Before
drilling bottom hole, make
sure 30" slide bar is plumb.
7b) Stud Option: R emove upper and
lower caps (P) from 30" slide bar
brackets. Place 30" slide bar
(R) into desired position. Using
brackets as a guide, carefully drill
1/8" pilot holes into stud.
Notes: Make sure that 30" slide bar
holes and bracket holes are aligned
before drilling. Before drilling bottom
hole, make sure 30" slide bar is
plumb.
8) With 30" slide bar (R) in position,
secure to wall using screws (Q).
Replace upper and lower caps (P)
onto 30" slide bar brackets.
4
4
1
1
2
2
3
R
P
P
1
1
2
2
3
R
P
P
2
2
1
Q
RR
P
P

6Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3047 REV 0 01/29/2014
3503-H321-V-CYL-B-TRM, 3505-H321-V-CYL-B-TRM,
3506-H321-V-CYL-B-TRM
Dia™Trim Series
Operation & Maintenance Manual
Installation
9) Install wall elbow (B) to stub out
pipe. Tighten Allen screw (3 mm)
(C) to secure.
10) Attach shower arm (D) and
ange (E) to vertical shower pipe
turning clockwise to tighten.
11) Install showerhead (F) to shower
arm (D). Turn clockwise to
tighten.
12) Attach large end of hand shower
hose (S) to hand shower head
(J). Attach small end of hand
shower hose (S) and gasket to
in-line vacuum breaker (A).
Connect in-line vacuum breaker
to wall elbow (B). Turn clockwise
to tighten.
1
2
D
E
3
1
4
2
S
J
A
S
B
1
2
C
B
1
2
F
D

7Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3047 REV 0 01/29/2014
3503-H321-V-CYL-B-TRM, 3505-H321-V-CYL-B-TRM,
3506-H321-V-CYL-B-TRM
Dia™Trim Series
Operation & Maintenance Manual
Operation
Temperature Control Diverter Control
1) Turn shower handle counterclockwise approximately
1/4 turn to put valve in cold position.
2) Turn shower handle counterclockwise approximately
1/2 turn to put valve in warm position.
3) Turn shower handle counterclockwise approximately
3/4 turn to put valve in hot position .
Note: 3505-H321-V-CYL-B-TRM, 3506-H321-V-CYL-B-
TRM only.
1) Diverter handle facing straight down is for diverter
function 1.
2) 3503-H321-V-CYL-B-TRM & 3505-H321-V-CYL-B-
TRM: Turn diverter handle counterclockwise one
full revolution for diverter function 2.
3506-H321-V-CYL-B-TRM: Turn diverter handle
counterclockwise 1/4 turn for diverter function 2.
3) 3506-H321-V-CYL-B-TRM: Turn diverter handle
counterclockwise 3/4 turn for diverter function 3.
3503-H321-V-CYL-B-TRM
3505-H321-V-CYL-B-TRM
3506-H321-V-CYL-B-TRM

8Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3047 REV 0 01/29/2014
3503-H321-V-CYL-B-TRM, 3505-H321-V-CYL-B-TRM,
3506-H321-V-CYL-B-TRM
Dia™Trim Series
Operation & Maintenance Manual
Care and Cleaning
1) Clean nished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse
with water.
Troubleshooting Chart
Problem Cause Solution
Finish is spotting. Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then
quickly rinse with water.