Symmons Duro SLS-3612-1.5 Manual

AA
B
B
D
D
C
CJJ
L
L
E
E
F
FG
G
H
H
KK
I
I
MM
O
O
C
CJJ
N
N
P
P
R
RI
I
LL
S
S
Q
Q
Model Numbers
Duro®Single Handle Lavatory Faucet
Operation & Maintenance Manual
SLS-3612-1.5, SLS-3622-1.5
Single handle lavatory faucet featuring a single hole
mounting conguration. Includes ceramic cartridge,
nylon braided hoses with 3/8" compression ttings, metal
drain assembly and standard 1.5 gpm (5.7 L/min) aerator.
Components made from brass and nonmetallic materials
plated in standard
polished chrome nish.
Specification
Warranty
Limited Lifetime - to the original end purchaser in
consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Compliance
Modifications
Note: Append appropriate -sufx to model number.
☐SLS-3612-1.5
Duro Single Handle Lavatory Faucet (6-7/8" height)
☐SLS-3622-1.5
Duro Single Handle Lavatory Faucet (4-1/2" height)
Dimensions
Note: Dimensions subject to change without notice.
c
Certied by
IAPMO R&T
Measurements
A1-11/16", 43 mm
B6-11/16", 170 mm
C
Hole Size:
Min. Ø 1-1/4", 32 mm
Max. Ø 1-1/2", 38 mm
D3/16", 5 mm
E 4-7/16", 113 mm
F8-7/16", 214 mm
G6-7/8", 175 mm
H5-5/16", 135 mm
I12°
J
Deck Thickness Ref.
Min. 7/8", 22 mm
Max. 2-1/2", 64 mm
K24", 610 mm
L3/8" compression tting
M 1-11/16", 43 mm
N 4-5/8", 118 mm
O 3/8", 9 mm
P 6-9/16", 167 mm
Q 4-1/2", 114 mm
R 3-1/2", 89 mm
S25", 635 mm
-ASME A112.18.1/CSA B125.1
-NSF/ANSI 61.9, NSF/ANSI 372
-WaterSense 1.5 gpm (5.7 L/min)
☐-0.5 0.5 gpm (1.9 L/min) aerator
☐-1.0 1.0 gpm (3.8 L/min) aerator
CG
CG

Parts Breakdown
2
Replacement Parts
Item Description Part Number
A
B
C
Handle
Set Screw
Plug Button
LN-01416
D Cartridge with Limit Stop RL-070
F
Aerator 1.5
Aerator 1.0
Aerator 0.5
RL-059-1.5
RL-059-1.0
RL-059-0.5
J
K
T
Lift Rod
Stopper
Ball Rod
RL-014
J Lift Rod RL-015
K Stopper RL-016
G, H
I
Y
Mounting Gaskets (2x)
Fasteners
Supply Hose
RL-011
Z Deck Plate RL-082
Required for Installation
Adjustable wrench
Allen wrench:
2.5mm
Plumber tape
Plumber putty
A
D
E
G
H
I
K
L
O
F
Y
B
C
J
M
N
P
Q
W
UV
T
S
R
X
OPTIONAL
Z

Installation
3
1a) SLS-3612: Insert faucet body (E)
through deck surface.
1b) SLS-3622: Insert faucet
body (E) through deck plate (Z)
and deck surface.
2) Slide mounting gasket (G) and
metal washer (H) on to fasteners (X).
Secure with mounting nuts (I).
Note: Hoses removed for clarity.
3) Install teon tape to inlets of
shut-off valves. Attach supply lines
to shut-off valves and hand tighten.
Using a wrench, nish with one-
half turn. DO NOT overtighten.
4) Apply plumber putty to underside
of ange (L).
5) Insert ange (L) into drain opening.
From below, attach drain body (Q)
with gasket (M) and washer (N) to
ange (2-3 turns until hand tight).
Note: Make sure drain cavity (on
drain body) faces rear of sink.
6) From below, tighten ange nut (O)
to secure drain body (Q).
DO NOT overtighten.
Note: Make sure ange is centered
in drain opening.
7) Insert stopper (K) into ange (L)
and rotate to proper position.
Note: Stopper can be installed
removable or non-removable
determined by eye hole position.
8) Insert pivot rod (T) into drain
body (Q) against gasket (P) and inner
seat (R). Install outer seat (S) against
pivot ball and secure assembly by
tightening retaining nut (U).
Note: Pivot rod passes under
stopper.
1
2
G
X
H
I
11
2
E
E
Z
L
3
1
2
L
Q
M
N
OPTIONAL
O
Q
Removable
K
Removable
K
Non Removable
K
L
1
T
S
U
Q
R
P
2

Installation
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2020 Symmons Industries, Inc. ■symmons.com ■[email protected] ■ZV-3152 REV E ■ 011320
9) Insert lift rod (J) into back of
faucet body (E). From below,
attach clevis strap (W) to lift
rod (J). Tighten thumb screw to
secure.
10) With stopper in closed location,
insert pivot rod (T) into clevis
strap (W). Secure with spring
clip (V).
11) To adjust stopper, select
another hole in clevis strap or
loosen thumb screw to slightly
raise or lower lift rod.
12) Attach drain body to drain trap.
13) The handle limit stop can
be set to limit handle turn to
the hot position. To measure
temperature, turn handle to
full hot position and lift handle
half way open. If water is too
hot or cold, loosen set screw
and remove handle. Remove
limit stop ring and rotate
counter clockwise to lower
temperature or clockwise to
raise temperature.
2
1
3
J
E
J
W
T
W
V
V
Hotter (+)
Colder (–)
1
3
22
Care and Cleaning
1) Clean nished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse
with water.
Troubleshooting Chart
Problem Cause Solution
Finish is spotting. Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then
quickly rinse with water.
Faucet is leaking from handle
or faucet body.
Cartridge o-rings are worn or foreign
matter (dirt, chips) is lodged between
cartridge and o-rings.
Remove cartridge and inspect for
foreign matter. Replace cartridge
if necessary.
Faucet no longer maintains desired
temperature.
Hard water deposits inside of
cartridge is preventing accurate mix
of hot and cold water.
Soak cartridge in white vinegar for
1 hour to breakdown hard water
deposits, then rinse with water.
Replace cartridge if necessary.
WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or
other reproductive harm. For more information, go to www.P65Warnings.ca.gov.