Symmons Naru SLW-4112 Quick guide

Fasten drain body and
tail piece to sink
Step 5
Step 1
Attach faucet spout
Step 3
Attach faucet handles
Step 2
Install stopper and pivot
rod to drain body
Step 6
Connect lift rod, clevis strap,
pivot rod and adjust linkage
Step 7
Attach control valves to sink
Step 1
Step 1
Connect hoses between
valve and spout
Step 4
Step 1
Connect supply lines
and check for leaks
Step 9
Flush water supply lines
before attaching
(reference installation details)
Step 8
Quick Install Guide Naru Widespread Lavatory Faucet, SLW-4112
Non-
Removable Removable
stopper stopper
HOT
COLD
Plumbers
Putty
Pipe
Sealant
3/32"
1 2 3 4
Alternate Finish Codes
-STN Satin Nickel
-PNL Polished Nickel finish
- Chrome (standard)
Model Numbers
SLW-4112 Lavatory faucet with
chrome nish and
includes pop-up drain
For California Residents
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Compliance
- ASME A112.18.1/CSA B125.1
- NSF/ANSI 61.9, NSF/ANSI 372
- WaterSense 1.5 gpm
Certied by
NSF International
 Need Help?
Contact Symmons customer service at
P: [phone], F: [phone]
Email: [email protected]
Monday - Friday 7:30 am - 7:00 pm EST
Please check Symmons website
for technical help, the latest product
information and warranty policy.
www.symmons.com/service
Tools & Materials
Installation and Service Instructions
Widespread Lavatory Faucet SLW-4112
Naru®

Caution: If replacing an older faucet ensure water supply is
turned OFF before removing. Then open faucet valves to relieve
water pressure.
Step 1 Attach control valves to sink
Step 2 Attach faucet handles
Step 3 Attach faucet spout
screw down until
thread stops
HOT
valve
Deck Front View
COLD
valve
3/32" Allen
wrench
OFF
position
CW=OFF
CCW=OFF
Step 4 Connect hoses between valve & spout
Step 5 Fasten drain body to sink
Pipe
Sealant
Required rotational swing
clearance at base of spout is
4 inches (100 mm) minimum.
back of sink
at edge
front of sink
bottom
view
1
2
PLUMBERS
PUTTY
ange
beveled
washer
friction
washer
ange nut
back
of sink
*ange washer
(optional)
*use included ange
washer only when
plumbers putty is
not available
tail
piece teon
tape
Installation Instructions
Page 2
Installation Instructions

Step 6 Install stopper and pivot rod to drain
Step 7 Connect lift rod and adjust linkage
Step 8 Flush supply lines before attaching
Care of faucet finish
■ Clean nish area by using mild soap and water or non-
abrasive cleaner and then rinse immediately. A non-abrasive
wax may be used to preserve nish area.
Valve cartridge replacement
Step 9 Connect supply lines, check for leaks
3/32" Allen
wrench
OFF
position
OFF
position
Replacing handles
17 mm deep
socket wrench
3 mm" Allen
wrench
3/32" Allen
wrench
OFF OFF
1 2 3
Drain body
1/2" (13 mm)
Pipe
Sealant
removable
1
2
non
removable
easily
removable
HOT
COLD
Ensure supply lines
are ushed clean
before attaching to
control valves.
Important
Supply hoses
not included.
HOT
COLD
Page 3

Part Number Item
Replacement Parts
handle assy.
1 ea. / kit
WSF-412L-KIT*
KN-113
identified
by groove
handle
(1) screw
collar
Note (1) screw requires
3/32" Allen wrench
Note (2) screw requires
3mm Allen wrench
KN-114-EXT-KIT
HOT cartridge kit
OFF=CW
KN-113-EXT-KIT
COLD cartridge kit
OFF=CCW
handle is used in
either hot or cold
locations
(2)
screw
cartridge extension
LN-532
FLR-103-1.5
FLR-103-1.0
ow regulator
2.2 gpm (8.3L/min)
1.5 gpm (5.7L/min)
1.0 gpm (3.8L/min)
Ordering replacement parts:
Call Symmons customer service at [phone]
M-F 7:30 am - 7:00 pm EST or check our website
at www.symmons.com for a list of Symmons distributors.
faucet handle
(reference table)
lift rod
LN-625-KIT*
stopper
P-100N*
pop-up drain
assembly
RL-154LR*
includes stopper
spout
LN-625-KIT*
valve cartridge
(reference table)
ow regulator
2.2 gpm (8.3 L/min)
(factory installed)
Valve body
(cold)
spout base
LN-625-KIT*
gasket
retainer
retainer nut
1/2 inch
brass coupling nut
(used in rigid piping
installations only)
gasket
ange nut
valve body (hot)
exible hose assy
mounting sleeve
*
Note: When ordering parts for faucets with an
optional decorative nish, append appropriate
three letter nish sufx code to part numbers
marked with an asterisk (*
).
Parts Assembly Naru Widespread Lavatory Faucet, SLW-4112
1/2"-14 NPSM
Hole size
1-1/4" (32 mm) min.
1-5/8" (41 mm) max.
4" (102 mm) min.
Flexible hose
2" dia.
(51 mm)
8"(203 mm) min.
16"(406 mm) max.
Deck thickness
5/16” (8 mm) min.
2-3/8" (60 mm) max.
Note: Dimensions subject to change without notice.
2-1/4" ( 73 mm)
5-1/2"
(139 mm)
2-1/4" dia.
(57 mm)
1-1/8" dia.
(28 mm)
7/8" dia.
(21 mm)
Hole size
1-3/8" (35 mm) min.
1-1/2" (38 mm) max.
3-1/2"
89 mm 5"
128 mm
2-7/8"
73 mm
2-7/8"
73 mm
1-1/2"
38 mm
5/8" (15 mm)
Dimensions Naru Widespread Lavatory Faucet, SLW-4112
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184
Phone: [phone] ■Fax: [phone]
Website:
symmons.com ■Email: [email protected]
Copyright © 2017 Symmons Industries, Inc. ■ZV-589 REV D ■082817