Symmons Origins S9612PP Manual

Model Numbers Feature Highlights
☐S9612PP Single handle centerset lavatory faucet
with A Push Pop Drain Assembly • 4" mount
• Quarter turn ceramic cartridge
• Push-pop metal drain assembly
• Standard 1.0gpm (3.8 L/min) flow rate
• Temperature limit stop included
• Components shall be metal and nonmetallic
construction, plated in standard polished chrome finish
Compliance
- ASME A112.18.1/CSA B125.1
- NSF/ANSI/CAN 61: Q<1, NSF/ANSI 372
- WaterSense 1.0 gpm (3.8 L/min)
Dimensions
Limited Lifetime - to the original end
purchaser in consumer/residential
installations.
10 Years - for commercial/industrial
installations. Refer to
www.symmons.com/warranty for
complete warranty information.
Warranty
S9612PP
Single Handle Centerset Lavatory Faucet
Operation & Maintenance Manual
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2023 Symmons Industries, Inc. ■symmons.com ■[e-mail] ■ZV-3723 REV 0 ■ 021723
Origins®
EE
GG
FF LL LL
HH
Measurements
EDeck Thickness Ref.
Max. 1 1/8", 29 mm
F3/8" Compression Fitting
GHole Size
Min. Ø 1 3/8", 35 mm
H(2x) Hole Size
Min. Ø 1 1/4", 32 mm
L1/4", 6 mm
Note: Dimensions subject to change without notice.
WARNING: This product can expose you to chemicals
including lead, which is known to the state of California to
cause cancer, birth defects, or other reproductive harm.
For more information, go to www.P65Warnings.ca.gov.

2
*Note: Append STN to part number for Satin Nickel
nish.
Replacement Parts
Item Description Part Number
A
B
C
Handle Kit RL-226*
G Cartridge RL-227
I Aerator RL-239-1.5* (1.5) RL-239-1.0* (1.0)
RL-239-0.5* (0.5)
J
L
M
Mounting Hardware RL-228
NPush Pop Drain Assem-
bly RL324*
(S9612)
O Grid Drain P-26*
(S9610)
Tools Required
Adjustable wrench
Allen wrench (3/32”)
Plumber putty
Plumber tape
Parts Breakdown
L
AB
C
D
E
G
H
I
J
K
M
O
N

3
H
J
K
2) Place brackets (L) onto threaded
rods (J). Secure with nuts (M).
1
1
2
M
L
J
If replacing an older faucet
ensure water supply is turned
OFF before removing, then
turn faucet control valve ON to
relieve water pressure.
1) Insert hoses from faucet body
(H) and threaded rods (J) through
mounting gasket (K) and sink
holes.
3) Push Pop Install: Insert drain
body (L) into drain opening. From
below, Tighten locking nut (O)
with gasket (M) and washer (N)
to ange. Tighten tail nut (Y) with
washer (X) to secure tail pipe (Q).
DO NOT overtighten.
Installation
DO NOT use pipe dope
or thread sealant on drain
assembly, or any plastic
threaded components.
1
2
3
Plumbers Putty L
Q
X
N
Y
O
M
4) Attach supply lines to shut-off
valves and hand tighten. Using a
wrench, nish with one-half turn.
DO NOT overtighten.
5) Remove aerator (I) and ush lines
free of debris. Check for leaks.
11
2
6) Adjust limit stop washer to limit
handle turn to the hot position if
desirable.
2
I
1
Note: Counterclockwise to lower
temperature, clockwise to increase
temperature.

Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2023 Symmons Industries, Inc. ■symmons.com ■[email protected] ■ZV-3723 REV 0 ■ 021723
Troubleshooting Chart
Finish is spotting. Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then quickly
rinse with water.
Maintenance
1) Turn off water supply. Remove
plug button (A). Loosen and
remove the handle set screw (B),
handle (C), collar (D) and nut (E).
3
2
1
5
A
B
7
6
4
E
C
D
2) Remove old cartridge. Correctly
align new cartridge (G) and insert
into faucet body (H). Install nut (E)
and secure collar (D).
3
4
2
5
H
1
D
E
G
3) Replace handle (C) and reinstall
set screw (B). Tighten set screw.
Reinstall plug button (A).
1
4
2
3
C
A
B

Números de modelo Características destacadas
☐S9612PP Grifo de baño de centros para el conjun-
to de centros de mango individual con
un conjunto de drenaje de empuje
• montura de 4”
• Cartucho cerámico de cuarto de vuelta
• Ensamblaje de drenaje de metal push-pop
• Caudal estándar de 1,0 gpm (3,8 l/min)
• Tope de límite de temperatura incluido
• Los componentes serán de construcción metálica y no
metálica, enchapados en un acabado de cromo pulido
estándar
Cumplimiento
- ASME A112.18.1/CSA B125.1
- NSF/ANSI/CAN 61: Q<1, NSF/ANSI 372
- WaterSense 1.0 gpm (3.8 L/min)
Dimensions
S9612PP
Grifo monomando central para lavabo
Manual de funcionamiento y mantenimiento
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2023 Symmons Industries, Inc. ■symmons.com ■[e-mail] ■ZV-3723 REV 0 ■ 021723
Origins®
EE
GG
FF LL LL
HH
Mediciones
EEspesor de la plataforma
Ref. máx. 1 1/8”, 29mm
F3/8" Ajuste de com-
presión
GTamaño del orificio mín. Ø
1 3/8”, 35mm
H(2x) Tamaño del orificio
mín. Ø 1 1/4”, 32mm
L1/4", 6 mm
Nota: Las dimensiones están sujetas a cambios sin previo aviso.
WARNING: This product can expose you to chemicals
including lead, which is known to the state of California to
cause cancer, birth defects, or other reproductive harm.
For more information, go to www.P65Warnings.ca.gov.
Vida Útil Limitada - Hasta el
comprador final original en
instalaciones residenciales/de
consumo.
10 Años - Para instalaciones
comerciales/industriales. Consulte
www.symmons.com/warranty para
obtener
La Garantía