Symmons SCOT S-60 Series SCOT S-61 Series Installation and maintenance instructions

Important: Water lines MUST be thoroughly ushed BEFORE
and AFTER installing the faucet to prevent foreign matter i.e.
copper chips, sand, stones, etc. from clogging and possibly
damaging the sealing surfaces of the cartridge.
INSTALLATION
(Supply stop valves must have a 3/8” O.D. compression outlet.)
1. S-60 Series: Remove nut and ferrule from supply stops, install
in-line check/screen assembly (LL-71B) on male outlet of stops.
2. Install SPF-KIT loosely on faucet. Position faucet through sink or
counter with mounting gasket under base. Secure faucet tighten-
ing nuts from under side.
3. Installdrainassembly.Sealunderangewithputty.
4. S-60 Series: Carefully bend copper supplies to meet water
supplies using palms of hands to avoid kinking tubing or fractur-
ing solder joints. Connect hot supply to left tube and cold supply
to right tube using appropriate lengths of 3/8” O.D. tubing
between faucet supplies and in-line check/screen assembly.
S-61 Series: Connect cold or tempered supply to faucet supply
using appropriate length of 3/8” O.D. tubing between faucet and
in-line check/screen assembly.
5. S-60 Series:Toushfaucetremoveaerator(LN-100or
LN-101)andturnvalvehandletofullcoldposition.Opensupply
anddepresshandleholdingdownfor10seconds,rotatehandleto
hot position, open supply and repeat above procedure. Hold down
handleandrotatefromlefttorighttoushlinesthoroughly.
Allow faucet to shut off and replace aerator.
S-61 Series:Toushfaucetremoveaerator(LN-100or
LN-101)andopensupplystopdepresshandleandholddownfor
10seconds.Repeatseveraltimesandallowfaucettoshutoff.
Replace aerator.
Adjustment of cycle time and temperature
After faucet has been operated through a number of cycles and
supply water temperature is at designed levels, adjustments to
these features can be made as follows.
Cycle Time: To increase time, loosen allen screw (LL-27) with
a3/32”hexsocketkey,removehandle(LT-100orRL-156)and
remove one or more of the washers (LL-28) on stem. To reduce
time, add washers.
Temperature limit adjustment (S-60 Series only):
Loosen allen screw (LL-27) with a 3/32” hex socket key.
Removehandle(RL-156),loosennut(LL-6)andturnstem(LL-
1A)todesiredmaximumtemperature(110°Frecommended).
Turnlimitstopwasher(LL-23N)clockwiseuntilapositivestop
isreachedagainstbackoffaucet.Tightennut(LL-6),replaceand
tightenhandle(RL-156).Faucetwilloperatefromthefullcold
position to the maximum hot temperature that has been set.
Reverse operation (S-60 Series only)
For piping simplicity in back to back installation or when hot
supply is on right, the faucets internal operation can be quickly
reversed.
 Removehandle(RL-156),nut(LL-6),andlimitstopwashers
(LL-22N)&(LL-23N),turnstem180°sothatredmarkingis
facing toward front.
Replace limit stop washers, adjust to desired temperature (see
adjustment procedure in preceding paragraph), reassemble faucet
reversing above procedure.
Faucet will operate from the full cold position to the maximum
hot temperature that has been set.
6"
152mm
39
16''
90mm
2"
51mm
23
16''
56mm
413
32
''
112mm
41
16''
103mm
cold
hot
117
32''
39mm
13
8''
23
8''
35mm
11
4''
32mm
61
2''
165mm
11"
279mm
3
8O.D.
copper
tubes
''
2"
51mm
2"
51mm
60mm
in-line
check/
screen
assembly
to fit stop
9
16 -24 thread
3
8compression
''
61
2''
165mm
6"
152mm
39
16''
90mm
2"
51mm
23
16''
56mm
413
32''
112mm
41
16''
103mm
117
32''
39mm
13
8''
35mm
11
4''
32mm
11"
279mm
3
8O.D.
copper
tube
''
2"
51mm
2"
51mm
23
8''
60mm
in-line
check/
screen
assembly
9
16 -24 thread
3
8
compression
''
S-60 Series
S-61 Series
SCOT S-60 Series
Slow-Closing Temperature Lavatory Faucet
Installation & Service Instructions
Metering Faucet S-61 Series
Metering Lavatory Faucet
For California Residents
WARNING: This product contains chemicals known to the
State of California to cause cancer, birth defects, or other
reproductive harm.

LL-1 Control spindle
LL-1A Control cartridge
LL-1B Control cartridge for
quick-closing
LL-2A Cycle spindle assembly
LL-3N Upper housing
LL-4 Piston washer screw
LL-6 Limit stop retainer nut
LL-8 Cycle spindle guide
LL-11 Piston cylinder
LL-12 Piston
LL-13 Inlet seat
LL-16 Shut-off seat
LL-22N Limit stop washer (xed)
LL-23N Limit stop washer (adjustable)
LL-24 Control rod
LL-27 Handle set screw
LL-28 Cycle time washers
LL-31 Retaining ring
LL-32 Piston spring
LL-33 Inlet seat springs (2)
LL-35 Thrust washer
LL-37 Shut-off washer
LL-42 Inlet seat o-rings (2)
LL-44 Spindle guide large o-ring
LL-45 Shut-off seat o-ring
LL-46 Control spindle small o-ring
LL-47 Control spindle large o-ring
LL-48 Upper housing o-rings (3)
LL-49 Piston o-ring
LL-71B In-line check/screen assembly (2)
LL-75 Spindle guide huva cup
LL-76 Huva cup retainer
RL-156 Handle
LL-105 Shell
LL-106 Base plate gasket
LL-107 Supply housing
LN-12 Anchor stud
LN-100 Aerator (vandal resistant 0.5 gpm)
LN-101 Aerator (vandal resistant)
LT-4A Piston assembly
SPF-KIT Mounting Kit
TT-36 Undercover plate screws (2)
Tools required for disassembly
Standard tools required:
Adjustable or 11/16" and 3/4" open end
wrench, small phillips screwdriver, pliers, 3/4"
deep socket
Repair Kit LL consists of:
LL-4, LL-8, LL-13, LL-24, LL-31, LL-32, LL-33,
LL-35, LL-37, LL-42, LL-43, LL-44, LL-45,
LL-46, LL-47, LL-48, LL-49, LL-73, LL-75,
LL-76.
LL-27
3/32" HEX SOCKET KEY RL-156
LL-28
LL-6
LL-23N
LL-22N
LL-105
LN-12
LN-100
LN-101
LL-13
LL-42
LL-33
LL-107
TT-36
LL-106
SPF-KIT
LL-71B
LL-3N
LL-48
LL-35
LL-1A
or
LL-1B
LL-1
LL-46
LL-47
LL-2A
LL-44
LL-8
LL-75
LL-76
LL-45
LL-16
LT-4A
LL-32
LL-31
LL-11
LL-4
LL-37
LL-24
LL-49
LL-12
PUSH
ON
SCOT® S-60 Series

LL-1 Control spindle
LL-1A Control cartridge
LL-1B Control cartridge for quick-closing
LL-2A Cycle spindle assembly
LL-3N Upper housing
LL-4 Piston washer screw
LL-8 Cycle spindle guide
LL-11 Piston cylinder
LL-12 Piston
LL-16 Shut-off seat
LL-24 Control rod
LL-27 Handle set screw
LL-28 Cycle time washers
LL-31 Retaining ring
LL-32 Piston spring
LL-35 Thrust washer
LL-37 Shut-off washer
LL-44 Spindle guide large o-ring
LL-45 Shut-off seat o-ring
LL-46 Control spindle small o-ring
LL-47 Control spindle large o-ring
LL-48 Upper housing o-rings (3)
LL-49 Piston o-ring
LL-75 Spindle guide huva cup
LL-76 Huva cup retainer
LL-105 Shell
LL-106 Base plate gasket
LN-12 Anchor stud
LN-100 Aerator (vandal resistant 0.5 gpm)
LN-101 Aerator (vandal resistant)
LT-4A Piston assembly
LT-71B In-line check/screen assembly
LT-100 Handle
LT-108 Supply housing
SPF-KIT Mounting Kit
TT-36 Undercover plate screws (2)
Tools required for disassembly
Standard tools required:
Adjustable or 11/16" and 3/4" open end wrench,
small phillips screwdriver, pliers, 3/4" deep
socket
Repair Kit LL consists of:
LL-4, LL-8, LL-13, LL-24, LL-31, LL-32, LL-33,
LL-35, LL-37, LL-42, LL-43, LL-44, LL-45,
LL-46, LL-47, LL-48, LL-49, LL-73, LL-75,
LL-76.
LL-27
3/32" HEX SOCKET KEY
PUSH
ON
LT-100
LL-28
LL-105
LN-12
LN-100
LN-101
LT-108
TT-36
LL-106
SPF-KIT
LT-71B
LL-3N
LL-48
LL-35
LL-1A
or
LL-1B
LL-1
LL-46
LL-47
LL-2A
LL-44
LL-8
LL-75
LL-76
LL-45
LL-16
LT-4A
LL-32
LL-31
LL-11
LL-4
LL-37
LL-24
LL-49
LL-12
Metering Faucet S-61 Series

1.General repair will require the repair or replacement of the
cartridge unit.
2. Shut off water supply to the faucet.
3. Remove handle with 3/32” hex socket key.
4. S-60 Series: Remove cycle time washers (LL-28), limit
stopretainernut(LL-6),andlimitstopwashers(LL-22Nand
LL-23N).
S-61 Series: Remove cycle time washers (LL-28).
5. S-60 Series: Removeupperhousing(LL-3N)withanadjust-
able wrench, slide housing off control cartridge (LL-1A).
S-61 Series: Removeupperhousing(LL-3N)withanadjust-
able wrench, slide housing off control cartridge (LL-1A).
6. S-60 Series: Control cartridge (LL-1A) can be either
replaced or repaired at this point. Disassemble cartridge
by opening retaining ring (LL-31) and sliding down piston
cylinder (LL-11).
S-61 Series: Control cartridge (LL-1A) can be either replaced
or repaired at this point.
7. S-60 Series: Ordinary service requires only the replacement of
the piston/o-ring assembly (LT-4A) and spring (LL-32). Com-
plete rebuilding of the cartridge can be accomplished with repair
KIT-LL.
S-61 Series: Ordinary service requires only the replacement of
the piston/o-ring assembly (LT-4A) and spring (LL-32). Com-
plete rebuilding of the cartridge can be accomplished with repair
KIT-LL.
8. S-60 Series: When re-installing cartridge be sure to align red
marking facing back on a normal installation and towards the
front on a reverse operation installation.
9. Reassemble, reversing above procedure.
SERVICE INSTRUCTIONS
TROUBLE SHOOTING CHART
melborP esuaC )snoitcurtsniecivreswolloF(noituloS
.trohsotrognolotsnurtecuaFgnimiT metsot)82-LL(srehsawddaneht-eldnahevomeR
nehtgnelotsrehsawevomerroemitnetrohsot
.emit
spirdtecuaF ,trid,spihc(rettamngierofronrowrehsawtaeS
.ecafrustaesdnarehsawneewtebsi).cte,redlos
notsipevomerdnaegdirtracelbmessasiD
.)73-LL(rehsawtaesnaelcdna4-LLwercsnU.)A4-TL(
.elbmessaernehtrrubrof)42-LL(nip.S.SkcehC
.yltnatsnocsnurtecuaF taesroecafrustaesnognisolctonrehsawtaeS
.nrowecafrustaesro/dnarehsaw
.)23-LL(gnirpsdna)A4-TL(notsipevomeR
htoB.gnirpskcehcdna)42-LL(nipnorrubrofkcehC
evissecxE.decalperebotevahyam23-LLdnaA4-TL
.A1-LLtnemecalperegdirtraceriuqeryamraew
.eldnahrednumorfskaelretaW .nrowsrehsawmetS gnisusrehsawecalperdnaegdirtracevomeR
.LL-TIK
.retnuocrednuronoskaeltecuaF .nrowsgnir-ognisuohylppuS .sgnir-o84-LLecalpeR
TOCS(dlocdnatohneewtebgnideelbtecuaF
.)ylnoseires06-S
sneercs/kcehcB17-LL ton .dellatsni deilppuserasneercs/kcehc”8/3detalpemorhcowT
dnatecuafyrevehtiw tsum .dellatsnieb
TOCS(dlocdnatohneewtebgnideelbtecuaF
.)ylnoseires06-S
sneercs/kcehcB17-LL era .dellatsni .staes31-LLecalpeR
.esoolsieldnaH .denesoolsahwercsteS .wercstesnethgiT
Remove handle (RL-156) and all timing washers
(LL-28) from cartridge. Secure handle back onto
cartridge. After moving handle to the hot position,
cycle faucet by pressing down on handle. Cycle
faucet 12 times. Remove handle and replace timing
washers.
Handle is sticking to cartridge. Accumulation of sediment in cartridge.
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184
Phone: [phone] ■Fax: [phone]
Website: www.symmons.com ■Email: [email protected]
Copyright © 2015 Symmons Industries, Inc. Printed in U.S.A. ■ZV-385 REV A ■111315