Symmons Ballina 5200-TRM Manual

Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3064 REV A 09/18/14
5200-TRM, 5201-TRM
Ballina™Trim Series
Operation & Maintenance Manual
Model Numbers Specifications
5200-TRM Valve Trim
5201-TRM Shower Trim
Shower trim includes shower escutcheon kit and 3 mode
showerhead with standard 2.5 gpm (9.5 L/min) ow
restrictor. Valve trim includes shower escutcheon kit only.
Components made from metal and nonmetallic materials
plated in standard polished chrome nish.
Modifications Compliance
-1.5 1.5 gpm (5.7 L/min) flow restrictor
-2.0 2.0 gpm (7.6 L/min) flow restrictor
-BBZ Brushed bronze finish
-STN Satin nickel finish
-ASME A112.18.1; CSA B125.1
Warranty
Limited Lifetime - to the original end purchaser in
consumer installations.
5 Years - for commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Note: Append appropriate -sufx to model number.
c

2
Dimensions
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3064 REV A 09/18/14
Measurements
A Ø 2 1/2", 64 mm
B 10 5/8", 268 mm
C 5 1/4", 132 mm
D 77", 1956 mm
E Ø 7 1/2", 191 mm
F 45", 1143 mm
G 3", 76 mm
H 4 1/8", 105 mm
I 3 1/2", 89 mm
J(Rough in)
2 3/8" ± 1/2", 60 mm ± 13 mm
Notes:
1) All dimensions measured from nominal rough-in (see J as reference).
2) Dimensions are subject to change without notice.
A
C
C
E
E
F
F
D
D
B
B
G
G
H
H
J
J
Floor
Floor
I
I

3
Parts Breakdown
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3064 REV A 09/18/14
Replacement Parts
Item Description Part Number
A Showerhead 412SH
B Shower Arm T-637
C
F
Handle
Set Screw T-660
D Dome Cover T-633
E
G
H
Mounting Screws
Shower Escutcheon
Mounting Plate
T-631-NS-K001
Notes:
1) Append -STN to part number for satin nickel nish;
-BBZ for brushed bronze.
2) Append -1.5 or -2.0 to showerhead or hand shower
for low ow.
Required for Installation
Adjustable wrench
Phillips head screwdriver
Allen wrench (1/8")
Plumber tape
F
B
A
G
H
D
C
E

4
Installation
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3064 REV A 09/18/14
Note:
For valve body installation, please
see valve body installation guide.
1) Install large plastic mounting
plate (H) to shower valve. Secure
with two screws (E).
2) Attach shower escutcheon (G) to
large plastic mounting plate (H).
Note: Tabs should snap into place.
3) Install dome cover (D) to valve by
turning clockwise.
4) Install handle (C) to valve.
Secure handles by tightening
set screw (F).
5) Attach shower arm (B) to vertical
shower pipe. Turn clockwise to
tighten.
6) Install showerhead (A) to shower
arm (B). Turn clockwise to tighten.
1
2
E
H
1
2
A
B
GH
1
2
D
1
2
CF
1
2
B

5Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3064 REV A 09/18/14
Care and Cleaning
1) Clean nished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse
with water.
Troubleshooting Chart
Problem Cause Solution
Finish is spotting. Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then
quickly rinse with water.
1) Turn shower handle counterclockwise approximately
1/4 turn to put valve in cold position.
2) Turn shower handle counterclockwise approximately
1/2 turn to put valve in warm position.
3) Turn shower handle counterclockwise approximately
3/4 turn to put valve in hot position.
Operation
Temperature Control