Symmons Origins S-243-LAM Series Quick guide

Non-
Removable Removable
stopper stopper
Quick Install Guide Origins Widespread Lavatory Faucet, S-243-2-LAM
Fasten drain body to sink
Step 5
Attach faucet handles
Step 2
Step 1
Attach control valves to sink
Step 1
SAttach faucet spout to sink
Step 3
Attach pivot rod to drain body
Step 7
Connect lift rod, clevis strap,
pivot rod and adjust linkage
Step 8
Install stopper and
set eye position
Step 6
Flush water supply lines
Step 10
Attach drain body to drain trap
Step 9
Step 4
SConnect water supply lines
Plumbers
Putty
Pipe
Sealant
Widespread Lavatory Faucet S-243-LAM Series
Installation and Service Instructions
Origins®
For California Residents
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Tools & Materials  Need Help?
Contact Symmons customer service at
[phone], [phone]
Email: [email protected]
Monday - Friday 8:00 am - 7:30 pm EST
Please check Symmons website
for technical help, the latest product
information and warranty policy.
www.symmons.com/service
Model Numbers
S-243-2-LAM Lavatory faucet
with pop-up drain
S-243-1-LAM Lavatory faucet
with lift rod only
S-243-LAM Lavatory faucet
Alternate Finish Code
append to part numbers when applicable
-STN Satin Nickel
-- Chrome (standard)
Compliance
- ASME A112.18.1/CSA B125.1
- NSF/ANSI 61.9, NSF/ANSI 372
- WaterSense 1.0 gpm & 1.5 gpm
Certied by
NSF International

Caution: If replacing an older faucet ensure water supply is
turned OFF before removing. en turn faucet control valves
ON to relieve water pressure.
Step 1 Attach control valves to sink
■ read ange nut about 2 inches down from threaded end
of valve body.
■ Insert valve body from
underneath sink up
through mounting hole.
Ensure valve with red
striped hose (hot) is on
the le and blue (cold) is
on the right.
■ Place gasket over
valve body and
thread fastener
onto valve body
until stop is reached.
■ Tighten ange nut and
mounting washer under sink and secure with mounting
screws if necessary.
■ read collar onto outer threads of fastener until against
surface of sink.
Step 2 Attach faucet handles
■ Turn valve spindles
to the OFF position.
HOT - le valve, clockwise
COLD - right valve,
counter clockwise
■ Attach handle to valve
spindle in OFF location
and tighten screw through
handle into valve spindle.
Step 3 Attach faucet
spout to sink
■ Unscrew tee and remove washer and
nut from threaded end
of spout as shipped.
■ Insert end of spout
through base and
mounting hole.
Fasten from under sink
with washer and nut.
■ Tighten nut while
ensuring spout and
base are centered
over mounting hole
and at edge of washer
is facing rear of sink.
Step 4 Connect water supply lines
■ read tee onto
end of spout.
Note: is may
require 4inches of
clearance.
■ Apply pipe sealant
on both ex hose
adapters. read
into side of tee.
■ Attach ex hoses to
ex hose adapters.
■ Plumb hot water
supply to le valve
body inlet, cold
water to right inlet
(supply hoses not
included).
■ Check for leaks if only replacing faucet and drain is already
installed by rst turning faucet handles to the OFF position
and then turn water supply valves ON.
Step 5 Fasten drain body to sink
■ Remove stopper, unscrew ange and remove at rubber
washer from end of drain body as shipped.
■ Apply plumber’s putty around bottom of ange.
■ Move friction washer,
beveled washer and
ange nut down away
from end of drain body.
■ Place ange into
drain opening and
screw drain body at
least 2-3 turns until
hand tight against ange.
Apply putty or teon
tape to tail piece and
attach to drain body.
■ Position drain body so
pivot cavity is facing rear
of sink and then slide
beveled washer and
friction washer up against
sink.
■ Tighten ange nut up
against friction washer
to evenly compress
beveled washer while also
ensuring ange is centered in drain opening.
Take care not to over tighten ange nut.
screw
handle
valve spindle
Pipe
Sealant
ex hose
spout
valve
outlet
&inlet
ex hose
adapter
tee
valve
body
spout
base
washer
nut
tee
collar
fastener
gasket
valve body
mounting washer
ange nut
mounting screws
PLUMBERS
PUTTY
ange
beveled
washer
friction
washer
pivot
cavity
ange nut
drain body
tail piece
Installation Instructions
Page 2

Step 10 Flush water supply lines
■ oroughly ush supply
lines to prevent foreign
matter, i.e. copper chips,
sand, etc. from damaging
the sealing surface
inside control valves.
■ Remove aerator
from end of faucet
water spout.
■ Turn hot and cold
faucet handles to full ON
position and then open water supply
valves and run long enough to ush supply lines thoroughly.
■ Turn faucet OFF, replace aerator and check for any leaks.
Care of faucet finish
Clean nish area by using mild soap and water or non-abrasive
cleaner and then rinse immediately. A non-abrasive wax may
be used to preserve nish area.
Step 6 Install stopper and set eye position
Stopper can be removable
or non-removable
determined by position
of eye hole when later
inserting pivot rod.
■ Insert stopper
through ange
opening and
position eye hole.
Removing stopper
When installed in removable position, move pivot rod to
the up position (li rod is in the down position when later
installed). Eye hole will slide over end of pivot rod.
Step 7 Attach pivot rod to drain body
■ Remove retaining
nut and outer seat
from pivot cavity.
■ Insert pivot rod into
pivot cavity so pivot
ball is against inner
seat and rod passes
under end of stopper
according to selected
eye hole position.
■ Slide outer seat over
pivot rod with curved end against pivot ball.
■ Fasten pivot rod to drain body with retaining nut.
Tighten using your ngers until ball is seated snug
and pivot rod can move around freely.
Step 8 Connect lift rod and adjust linkage
■ Insert li rod through
hole on rear of water
spout.
■ Fasten end of pivot rod
with spring clip through
location hole in clevis
strap that is best aligned
to enable li rod also
fasten to end of clevis
strap when in the up
position and stopper is
in the closed position.
■ Insert li rod into
end of clevis strap
and fasten with thumb
screw at location where
stopper can be easily
opened and closed.
If necessary, select another location hole in clevis
strap and re-adjust li rod where fastened to clevis strap.
Step 9 Attach drain body to drain trap
Step 1 Remove faucet handle
Loosen screw using a 5/64 inch
Allen wrench.
Step 2 Remove collar
Remove collar by turning
counter clockwise.
Note: Ensure not to use any tool
that could scratch nish without
taking protective measures.
Step 3 Remove cartridge
Using a wrench, turn hex nut
on cartridge counter clockwise.
Note: Ensure valve assembly
under sink doesn’t rotate while
turning nut.
Step 4 Insert new cartridge
Insert replacement cartridge
and then tighten hex nut.
Step 5 Attach collar
Screw collar onto fastener and tighten using your hand.
Step 6 Attach faucet handle
■ Ensure cartridge spindle is
rotated to the OFF position.
■ Attach handle in OFF location
as shown in illustration and
then tighten screw using a
5/64 inch Allen wrench.
remove
aerator
Valve cartridge replacement
stopper
ange
non
removable removable
pivot rod
retaining nut
outer seat
pivot ball
inner seat
pivot cavity
thumb
screw
location
holes
spring
clip
pivot rod
clevis strap
lift rod
hot = cw
cold = ccw
spindle OFF
cartridge
valve
screw
handle
collar
handles set in the
OFF position
Page 3

Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184
Phone: [phone] ■Fax: [phone]
Website: symmons.com ■Email: gethelp@symmons.c o m
Copyright © 2017 Symmons Industries, Inc. ■ZV-788 REV B ■082817
aerator
handle
set screw
Replacement Parts
Part Number Item
LN-15*
FLR-110-1.5*
FLR-110-1.0*
aerator ow rates
2.2 gpm (8.3L/min)
1.5 gpm (5.7L/min)
1.0 gpm (3.8L/min)
collar
LN-112*
LN-128*
LN-129
escutcheon
escutcheon gasket
LN-114-LAM-KIT*
1 handle included
KN-114 (hot)
OFF = CW
KN-113 (cold)
OFF = CCW
KN-113
identified
by groove
valve cartridge
stopper
P-100N
pop-up drain
assembly
RL-154LR*
includes lift rod
and stopper
(red stripe on hot hose)
(blue stripe
on cold hose)
Parts Assembly Origins Widespread Lavatory Faucet, S-243-2-LAM
Ordering replacement parts:
Call Symmons customer service at [phone],
[phone] M-F 8:00 am - 7:30 pm EST or
check our website at www.symmons.com for a
list of Symmons distributors.
standard
aerator
2.2 gpm
faucet
handle
valve
cartridge
lift rod
P-108CL12*
*Note: For faucets with an optional decorative
nish, append appropriate three letter sufx code to
part numbers marked with an asterisk (*).
Reference
replacement
parts table
1" dia. (25 mm)
Hole size
1-1/16" (27 mm) min
1-7/16" (37 mm) max
1/2"-14 NPSM
Note: Dimensions subject to change without notice.
2-1/4" (57 mm)
2" dia. (51 mm)
4" (102 mm) min.
8" (203 mm) min.
16" (406 mm) max.
11/16" dia. (17 mm)
Hole size
1-1/8" (29 mm) min.
1-1/2" (38 mm) max.
5/8" (16 mm)
Flexible hose
Deck thickness
1-3/8" (35 mm) max.
Dimensions Origins Widespread Lavatory Faucet, S-243-2-LAM
2-1/2"
(63 mm) dia
5-3/8"
(136 mm) 1-7/8"
(47 mm)
7-1/4"
(184 mm)
6-3/8"
(162 mm)
5-1/16"
(128 mm)
5-3/16"
(55 mm)