Syris RD200-MIC User manual

RD200/300 TOOL
OPERATION MANUAL
V02.10

1
Model description.............................................................................................................................2
Installation........................................................................................................................................3
Driver installation (For change to virtual COM port mode)...............................................................4
Common Setting..............................................................................................................................5
Auto Read (13.56 MHz only)..........................................................................................................10
NTAG/Ultralight (13.56 MHz only)..................................................................................................11
MIFARE (Mifare only).....................................................................................................................13
MIFARE Key ..................................................................................................................................14
LF Card (RD200-LF 125KHz only).................................................................................................16
EPC/eTag (RD200-U1 UHF reader only) .......................................................................................17
DESFire (13.56MHz only)..............................................................................................................18
ISO 14443B (13.56MHz only)........................................................................................................19
ISO 15693 (RD200-MIC & RD300 MHz supported).......................................................................20
Fingerprint (RD300-FH1 only)........................................................................................................21
Command Test...............................................................................................................................23
Firmware Update ...........................................................................................................................24

2
Model description
Model
Picture
Difference description
RD200-M1
HF RFID Desktop Reader
Frequency: 13.56 MHz
Support tag: ISO-14443A / Mifare Ultralight / NTAG203
RD200-MIC
HF RFID Desktop Reader
Frequency: 13.56 MHz
Support tag: ISO-15693 / ISO-14443A/ ISO-14443B / Felica /
NTAG203
RD200-LF
LF RFID Desktop Reader
Frequency: 125 KHz
Support tag: EM4100 compatible class / SYRIS/ FDX-B(ISO11784)
RD200-U1
UHF RFID Desktop Reader
Frequency: 860~960MHz
Support tag: Compatible with EPC Class 1 Gen 2;ISO-18000-6C
RD300-H1-G
HF RFID Desktop Reader
Frequency: 13.56 MHz
Support tag: ISO15693 / ISO14443A(Mifare) / ISO14443B / DESFire
/ NTAG203
RD300-FH1-G
HF RFID and Fingerprint Desktop Reader
High accuracy and high recognition speed Optical Fingerprint Sensor
Frequency: 13.56 MHz
Support tag: ISO15693 / ISO14443A(Mifare) / ISO14443B / DESFire
/ NTAG203
RD300-L1-G
LF RFID Desktop Reader
Frequency: 125 KHz
Support tag: EM4100 compatible class / SYRIS/ FDX-B(ISO11784)
RD300-FL1-G
LF RFID and Fingerprint Desktop Reader
High accuracy and high recognition speed Optical Fingerprint Sensor
Frequency: 125 KHz
Support tag: EM4100 compatible class / SYRIS/ FDX-B(ISO11784)

3
Installation
The default setting of USB Mode is USB Keyboard Emulation. This Keyboard mode would send
an "Enter" signal when read the card. If user let cursor focus on "Set" button and read the card that
will press the "Set" button at the same time.

4
Driver installation (For change to virtual COM port mode)
1. Follow firmware update procedure to change virtual COM port mode firmware.
(ex. RD200_U1_COM_V0191_20150316.SYB)
2. Connect RD200/RD300, system will automatically pop-up the "Found New Hardware Wizard"
window for install the driver.
3. Allocate the driver folder, and then complete the installation.
(SYRIS_RFID_DVD\RD200\Driver)

5
Common Setting
1. USB Mode
There are three selections of USB modes in "USB auto" connection, after selected the mode
then click Set to finish the setting procedure, or click Get Current Setting to read current
setting from the reader.
USB Keyboard Emulation：
The device can emulate keyboard to send character or string to host terminal.
USB HID-Compliant Device：

6
Device response data when received protocol command, and the data will be queued in device
buffer.
USB HID-Compliant Device Auto Send：
The device sends UID to host terminal after read card.
2. Virtual COM Port mode (Need update firmware)
There are two selections of USB modes in "COM x" connection.
USB Serial Port Auto Send：
The device send UID to host terminal after read card.
USB Serial Port：
Device response data when received protocol command, and the data will be queued in device
buffer.
3. USB Keypad Delay Time
In this mode, you can set keypad delay timing to reduce the key code sending speed when
read tag.

7
4. Read Card Mode
In this mode, program provided different options for user to choose, after ticked the options,
just click Set to finish the setting procedure, or click Get Current Setting to read current setting
from the reader.
Options
Descriptions
Auto
Automatically read card
Beep
Prompt the beep sound or not.
LED
Flash the LED when read the card.
Same Card Detection
If continuously read the same card, user has to wait around 1.5 sec then
could read again.
Energy Saving Mode
Provide more energy saving method.
(It is not recommend to use in writing card blocks or several cards)
eTag
Read Taiwan ETC eTag format.
5. System Command
This tool provides two system commands; user can use Reboot Reader to reboot the RD200
reader. The other command is Use Factory Default Settings which can restore the reader
settings to initial settings.

8
6. Send ID Format
This tool provide many ID format to choose,
such as 4~16 numbers of hexadecimal and
4~13 numbers of decimal.
Also can put comma, space…etc. into the ID
format, after ticked the items then click Set to
finish the setting procedure, or click Get
Current Setting to read current setting from the reader.
The ID format example as below:
ID Format
Example Result
4H
58E8
6H
D558E8
8H
00D558E8
10H
1800D558E8
16H
0000001800D558E8
32H
00000000000000000000001800D558E8
5D
47295
8D
01226943
10D
0001226943
13D
0098785474751
4D
6493
FDX (LF only)
000000001226943
16H + Card ID Reverse
E858D50018000000
16H + Comma
0000001800D558E8,
16H + Brackets
[0000001800D558E8]
4D + Space
1928 1928
16H + Quotation
'0000001800D558E8'

9
7. Read Card Time Postponement / Same Card Detection Time
Read Card Time Postponement: The intermission time of card reading.
Same Card Detection Time: The intermission time of same card detection.
After adjusted the time then click Set to finish the setting procedure, or click Get Current
Setting to read current setting from the reader.