Syris SYSR86N-HBX1 User manual

SYSR86N-HBX1
Standard TCP/IP Reader
Manual
Version 01.04
2016/04/25

SYSR86N Standard TCP/IP Reader Operation Manual
1
I. Features & Specification
Feature:
 Standard 86.0(W)x86.0(H) mm
 Waving Hand / Touch Panel to Access Door
 Support to read standard 13.56MHz RFID card
 Relay for door bell、light or EM lock
 Quick Setup via Micro USB
 Support Standard Wiegand interface
 Door sensor detective ( Door Open Timeout、Forcible Entry Alarm )
 Support Black card List
 Support to access door via Bluetooth、Xtive RFID Tag
Specification:
Card Frequency 13.56MHz
Card Types ISO14443A/B / ISO15693 / Mifare / NTAG203/ DESFire
Card Read Range 1~5 cm
Ethernet 10/100 base-T Ethernet
Wi-Fi 802.11 b/g/n
Black/White List 500
Event Log 1180
Baud Rate 19,200 bps (4,800~230,400 bps)
Read Card Time 0.1 second
Keypad 1 Key (Capacitive Touch)
IR Sensor 1 IR Sensor, adjustable range 0-10 cm
Status Indicator Tricolor LED(RGB)
Touch Status Indicator Tricolor LED(RGB)
Interface Ethernet, Wi-Fi, Wiegand, RS-485, USB
Device ID 0001~9999
Digital Input Up to 3 (1 no-voltage DI +2 no-voltage DI share the same port with
Wiegand)
Digital Output Up to 4 (2 Relay + 2 output share the same port with Wiegand)
Voice Output On-Board Buzzer
Operation/Storage Temperature -10℃~+60℃ / -20℃~+70℃
Power 8V ~ 28V DC / 1W ~ 6W
Size(mm) 86(W) x 86(H) x 41.6(D) mm (No Wire Included)

SYSR86N Standard TCP/IP Reader Operation Manual
2
II. Wiring Diagram

SYSR86N Standard TCP/IP Reader Operation Manual
3
III. Network Parameter Setting
1. Execute “NET_Discover_V0110.exe” and press to search SY86N series product.
2. Factory default IP is “192.168.1.101”. User can check the MAC address from product sticker with IP
to confirm the device.

SYSR86N Standard TCP/IP Reader Operation Manual
4
3. Double click IP (192.168.1.101) to open the web configure page(http://192.168.1.101)
Default login ID / Password : admin / admin

SYSR86N Standard TCP/IP Reader Operation Manual
5
4. Default Net Mode is the same as the following. User can modify Net Mode and other parameters. If
device cannot communicate properly after setting, user can reset NET module via Micro USB.
Communication Parameter Factory Default
Serial Configure 230400,8,n,1
Serial Framing Length 1050
Locale/Remote Port Number 5001

SYSR86N Standard TCP/IP Reader Operation Manual
6
IV. Network Mode Switch
86N series device support 4 network modes: Dual mode、ETH(Ethernet)、Wi-Fi AP、Wi-Fi client.
Default Ethernet (DHCP) +Wi-Fi AP mode
ETH-SERIAL Ethernet only (Factory Default)
WIFI(CLIENT)-SERIAL Wi-Fi client mode
WIFI(AP)-SERIAL Wi-Fi AP mode
1. ETH-SERIAL：Factory default is ETH-SERIAL. ( Standard TCP/IP Reader )
When user modify the IP and click on Apply button, device will reboot and apply the setting after 30
seconds.

SYSR86N Standard TCP/IP Reader Operation Manual
7
2. Wi-Fi client mode：86N can be set to communicate via Wireless AP without Ethernet.
SSID: Enter the SSID from AP you will connect to network.
Scan : User can scan AP in range of 86N and select one to connect. But user cannot scan the AP
after changing default network mode (Ethernet only) to Wi-Fi (Client). 86N need to power off / on to
enable the scan function.
Encrypt Type : Select Encrypt type for AP connection.
Password: Enter password for AP.
IP Type: DHCP is default mode. If user have to setup a static IP, please select Static.
PS: Wi-Fi MAC address is Ethernet MAC subtract 1.
Ex. Ethernet MAC : AC:A2:13:B5:5A:B5， Wi-Fi MAC : AC:A2:13:B5:5A:B4

SYSR86N Standard TCP/IP Reader Operation Manual
8
3. Wi-Fi AP mode：Setup 86N as AP(Wireless Access Point) for client device to communicate. This mode is
usually for setting device.
SSID: Setup 86N device’s SSID.
Encrypt Type : Select Encrypt Type for the AP.
Password: Setting 86N device’s Wi-Fi password.
IP address: Setting 86N device’s Wi-Fi IP address.
Subnet Mask: Setting 86N device’s Wi-Fi subnet mask.

SYSR86N Standard TCP/IP Reader Operation Manual
9
4. Default mode：Ethernet (DHCP) +Wi-Fi AP mode.
It’s Dual-Mode ( Ethernet and Wi-Fi AP，but Ethernet only support DHCP.)
SSID: Setup 86N device’s SSID.
Password: Setting 86N device’s Wi-Fi password.