System air SYSCROLL 20 AIR EVO HP Manual

English Deutsch EspañolItalianoFrançais
Air Cooled Water Chillers and Heat Pumps
Refroidisseurs de liquide à condensation par air et pompes à chaleur air-eau
Luftgekühlte Flüssigkeitskühler und Wärmepumpen
Refrigeratori d’Acqua e Pompe di Calore Raffreddati ad Aria
Enfriadores de Agua y Bomba de Calor Condensadas con Aire
Водяные чиллеры с воздушным охлаждением и тепловые насосы
Installation and maintenance manual
Manuel d’installation et de maintenance
Installations- und Wartungshandbuch
Manuale di installazione e di manutenzione
Manual de instalación y de mantenimiento
Инструкция по монтажу и техобслуживанию
SYSCROLL 20-30 AIR EVO HP
Part number / Code / Code / Codice / Código / Номер детали: 364321/J
Supersedes / Annule et remplace / Annulliert und ersetzt / Annulla e sostituisce / Anula y
sustituye / Замена: 364321/I
Notified Body / Organisme Notifié / Benannte Zertifizierungsstelle / Organismo
Notificato / Organismo Notificado / Уведомленный орган N°. 0425
ISO 9001:2015 certified management system
Русское
издание
7

33 kW
7

35 kW

1
English
Table of Contents
1 - FOREWORD
1.1 Introduction..........................................................................2
1.2 Warranty..............................................................................2
1.3 Emergency stop / Normal stop .............................................2
1.4 An introduction to this manual ..............................................2
2 - SAFETY
2.1 Foreword..............................................................................3
2.2 Definitions............................................................................4
2.3 Access to the unit ...............................................................4
2.4 General precautions..............................................................4
2.5 Precautions against residual risks.........................................4
2.6 Precautions during maintenance operations ..........................5
2.7 Safety labels ................................................................. 6 & 7
2.8 Safety regulations........................................................8 to 10
3 - TRANSPORT, HANDLING AND STORAGE
3.1 Inspection ..........................................................................11
3.2 Handling ............................................................................11
3.3 Anchoring ..........................................................................12
3.4 Storage ..............................................................................12
4 - INSTALLATION
4.1 Installation site ...................................................................13
4.2 External water circuit .................................................13 to 15
4.3 Water connections .............................................................15
4.4 Defrost water drainage .......................................................15
4.5 Water buffer tank ...................................................... 15 & 16
4.6 Power supply ............................................................ 16 & 17
4.7 Electrical connections................................................ 18 & 19
5 - START-UP
5.1 Preliminary checks.............................................................20
5.2 Start-up .............................................................................20
5.3 Checking the operation.......................................................20
5.4 Delivery to the customer.....................................................20
6 - CONTROL
6.1 Control of SYSCROLL 20/30 AIR EVO HP single compressor,
variable speed....................................................................21
6.2 Alarms...............................................................................22
6.3 Menus ......................................................................22 to 25
6.4 Alarm list ...........................................................................25
7 - PRODUCT DESCRIPTION
7.1 General information ............................................................26
7.2 Accessories ..............................................................27 to 29
7.3 Refrigeration circuits ..........................................................30
8 - TECHNICAL DATA
8.1 Hydraulic features ..............................................................31
8.2 Physical data......................................................................33
8.3 Electrical data.....................................................................34
8.4 Dimensional Drawings............................................... 35 & 36
8.5 Space requirements ...........................................................37
9 - MAINTENANCE
9.1 General requirements .......................................................38
9.2 Planned maintenance........................................................38
9.3 Refrigerant charge.............................................................39
9.4 Compressor......................................................................39
9.5 Condenser .......................................................................39
9.6 Fans .................................................................................39
9.7 Dehydrating filter...............................................................39
9.8 Sight glass........................................................................40
9.9 Thermostatic expansion valve............................................40
9.10 Evaporator ........................................................................40
10 - TROUBLESHOOTING .......................................... 41
11 - SPARE PARTS
11.1 Spare part list.....................................................................42
11.2 Oil for compressors............................................................42
11.3 Wiring diagrams.................................................................42
12 - DISMANTLING, DEMOLITION AND SCRAPPING
12.1 Generalities ........................................................................43
12.2 RAEE Directive....................................................................43

2
1 - Foreword
1.1 Introduction
Units, manufactured to state-of-the-art design and implementation
standards, ensure top performance, reliability and fitness to any type
of air-conditioning systems.
These units are designed for cooling water or glycoled water (and for
water heating in heat pump models) and are unfit for any purposes
other than those specified in this manual.
This manual includes all the information required for a proper
installation of the units, as well as the relevant operating and
maintenance instructions.
It is therefore recommended to read this manual carefully before
installation or any operation on the machine. The chiller installation
and maintenance must be carried out by skilled personnel only
(where possible, by one of Authorised Service Centers).
The manufacturer may not be held liable for any damage to people or
property caused by improper installation, start-up and/or improper
use of the unit and/or failure to implement the procedures and
instructions included in this manual.
1.2 Warranty
These units are delivered complete, tested and ready for being
operated. Any form of warranty will become null and void in the event
that the appliance is modified without manufacturer’s preliminary
written authorisation.
This warranty shall apply providing that the installation instructions
have been complied with (either issued by manufacturer, or deriving
from the current practice), and the Form 1 (“Start-up”) has been
filled-in and mailed to manufacturer (attn. After-Sales Service).
In order for this warranty to be valid, the following conditions shall
be met:
nThe machine must be operated only by skilled personnel from
Authorised After-Sales Service.
nMaintenance must be performed only by skilled personnel - from
one of Authorised After-Sales Centers.
nUse only original spare parts.
nCarry out all the planned maintenance provided for by this manual
in a timely and proper way.
Failure to comply with any of these conditions will automatically void
the warranty.
1.3 Emergency stop / Normal stop
The emergency stop of the unit can be enabled using the master
switch on the control panel (move down the lever).
For a normal stop, press the relevant push-buttons.
To restart the appliance, follow the procedure detailed in this manual.
1.4 An introduction to the manual
For safety reasons, it is imperative to follow the instructions given
in this manual. In case of any damage caused by non-compliance
with these instructions, the warranty will immediately become null
and void.
Conventions used throughout the manual:
DANGER
The DANGER sign recalls your attention to
a certain procedure or practice which, if not
followed, may result in serious damage to
people and property.
WARNING
The WARNING sign precedes those procedures
that, if not followed, may result in serious
damage to the appliance.
NOTE
The NOTE contain important observations.
USEFUL TIPS
The USEFUL TIPS provide valuable information
that optimises the efficiency of the appliance.
This manual and its contents, as well as the documentation which
accompanies the unit, are and remain the property of manufacturer,
which reserves any and all rights thereon. This manual may not
be copied, in whole or in part, without manufacturer’s written
authorization.

3
English
2 - Safety
2.1 Foreword
These units must be installed in conformity with the
provisions of Machinery Directive 2006/42/EC, Pressure
Equipment Directive 2014/68/EU, Electromagnetic
Compatibility Directive 2014/30/EU, as well as with other
regulations applicable in the country of installation. If these
provisions are not complied with, the unit must not be
operated.
DANGER
The unit must be grounded, and no
installation and/or maintenance operations
may be carried out before deenergising the
electrical panel of the unit.
Failure to respect the safety measures mentioned above may result
in electrocution hazard and fire in the presence of any short-circuits.
DANGER
Inside the heat exchangers, the compressors
and the refrigeration lines, this unit contains
liquid and gaseous refrigerant under
pressure. The release of this refrigerant may
be dangerous and cause injuries.
DANGER
The units are not designed to be operated with
natural refrigerants, such as hydrocarbons.
Manufacturer may not be held liable for any
problems deriving from the replacement
of original refrigerant or the introduction of
hydrocarbons.
Units are designed and manufactured according to the requirements
of European Standard PED 2014/68/EU (pressure vessels).
nThe used refrigerants are included in group II (non-hazardous
fluids).
nThe maximum working pressure values are mentioned on the
unit’s data plate.
nSuitable safety devices (pressure switches and safety valves)
have been provided, to prevent any anomalous overpressure
inside the plant.
nThe vents of the safety valves are positioned and oriented in such
a way as to reduce the risk of contact with the operator, in the
event that the valve is operated. Anyway, the installer will convey
the discharge of the valves far from the unit.
nDedicated guards (removable panels with tools) and danger signs
indicate the presence of hot pipes or components (high surface
temperature).
DANGER
The guards of the fans (only for units provided
with air heat exchangers) must be always
mounted and must never be removed before
de-energising the appliance.
DANGER
It is the User’s responsibility to ensure that
the unit is fit for the conditions of intended use
and that both installation and maintenance are
carried out by experienced personnel, capable
of respecting all the recommendations
provided by this manual.
It is important that the unit is adequately
supported, as detailed in this manual. Non-
compliance with these recommendations may
create hazardous situations for the personnel.
DANGER
The unit must rest on a base which meets the
characteristics specified in this manual; a
base with inadequate characteristics is likely
to become a source of serious injury to the
personnel.
WARNING
The unit has not been design to withstand
loads and/or stress that may be transmitted by
adjacent units, piping and/or structures.
Each external load or stress transmitted to the
unit may break or cause breakdowns in the
unit’s structure, as well as serious dangers to
people. In these cases, any form of warranty will
automatically become null and void.
WARNING
The packaging material must not be disposed of
in the surrounding environment or burnt.

4
2 - Safety
2.2 Definitions
OWNER: means the legal representative of the company, body or
individual who owns the plant where unit has been installed; he/she
has the responsibility of making sure that all the safety regulations
specified in this manual are complied with, along with the national
laws in force.
INSTALLER: means the legal representative of the company who has
been given by the owner the job of positioning and performing the
hydraulic, electric and other connections of unit to the plant: he/she is
responsible for handling and properly installing the appliance, as specified
in this manual and according to the national regulations in force.
OPERATOR: means a person authorised by the owner to do on unit
all the regulation and control operations expressly described in this
manual, that must be strictly complied with, without exceeding the
scope of the tasks entrusted to him.
ENGINEER: means a person authorised directly by manufacturer or,
in all EC countries, excluding Italy, under his full responsibility, by
the distributor of product, to perform any routine and extraordinary
maintenance operations, as well as any regulation, control, servicing
operations and the replacement of pieces, as may be necessary
during the life of the unit.
2.3 Access to the unit
The unit must be placed in an area which can be accessed also
by OPERATORS and ENGINEERS; otherwise the unit must be
surrounded by a fence at not less than 2 meters from the external
surface of the machine.
OPERATORS and ENGINEERS must enter the fenced area only
after wearing suitable clothing (safety shoes, gloves, helmet etc.).
The INSTALLER personnel or any other visitor must always be
accompanied by an OPERATOR.
For no reason shall any unauthorised personnel be left alone in
contact with the unit.
2.4 General precautions
The OPERATOR must simply use the controls of the unit; he must not
open any panel, other than the one providing access to the control
module.
The INSTALLER must simply work on the connections between plant
and machine; he must not open any panels of the machine and he
must not enable any control.
When you approach or work on the unit, follow the precautions listed
below:
nDo not wear loose clothing or jewellery or any other accessory tat
may be caught in moving parts.
nWear suitable personal protective equipment (gloves, goggles
etc.) when you have to work in the presence of free flames
(welding operations) or with compressed air.
nIf the unit is placed in a closed room, wear ear protection devices.
nCut off connecting pipes, drain them in order to balance the
pressure to the atmospheric value before disconnecting them,
disassemble connections, filters, joints or other line items.
nDo not use your hands to check for any pressure drops.
nUse tools in a good state of repair; be sure to have understood the
instructions before using them.
nBe sure to have removed all tools, electrical cables and any other
objects before closing and starting the unit again.
2.5 Precautions against residual risks
Prevention of residual risks caused by the control
system
n Be sure to have perfectly understood the operating instructions
before carrying out any operation on the control panel.
nWhen you have to work on the control panel, keep always the
operating instructions within reach.
nStart the unit only after you have checked its perfect connection
to the plant.
nPromptly inform the ENGINEER about any alarm involving the
unit.
nDo not reset manual restoration alarms unless you have identified
and removed their cause.
Prevention of residual mechanical risks
nInstall the unit according to the instructions provided in this
manual.
nCarry out all the periodical maintenance operations prescribed by
this manual.
nWear a protective helmet before accessing the interior of the unit.
nBefore opening any panelling of the machine, make sure that it is
secured to it by hinges.
nDo not touch air condensation coils without wearing protective
gloves.
nDo not remove the guards from moving elements while the unit is
running.
nCheck the correct position of the moving elements’ guards before
restarting the unit.
Prevention of residual electrical risks
nConnect the unit to the mains according to the instructions
provided in this manual.
nPeriodically carry out all the maintenance operations specified by
this manual.
nDisconnect the unit from the mains by the external disconnecting
switch before opening the electrical board.
nCheck the proper grounding of the unit before start-up.
nCheck all the electrical connections, the connecting cables, and in
particular the insulation; replace worn or damaged cables.

5
English
2 - Safety
nPeriodically check the board’s internal wiring.
nDo not use cables having an inadequate section or flying
connections, even for limited periods of time or in an emergency.
Prevention of other residual risks
nMake sure that the connections to the unit conform to the
instructions provided in this manual and on the unit’s panelling.
nIf you have to disassemble a piece, make sure that it has been
properly mounted again before restarting the unit.
nDo not touch the delivery pipes from the compressor, the
compressor and any other piping or component inside the
machine before wearing protective gloves.
nKeep a fire extinguisher fir for electrical appliances near the
machine.
nOn the units installed indoor, connect the safety valve of the
refrigeration circuit to a piping network that can channel any
overflowing refrigerant outside.
nRemove and leak of fluid inside and outside the unit.
nCollect the waste liquids and dry any oil spillage.
nPeriodically clean the compressor compartment, to remove any
fouling.
nDo not store flammable liquids near the unit.
nDo not disperse the refrigerant and the lubricating oil into the
environment.
nWeld only empty pipes; do not approach flames or other sources
of heat to refrigerant pipes.
nDo not bend/hit pipes containing fluids under pressure.
2.6 Precautions during maintenance operations
Maintenance operations can be carried out by authorised technicians
only.
Before performing any maintenance operations:
nDisconnect the unit from the mains with the external disconnecting
switch.
nPlace a warning sign “do not turn on - maintenance in progress”
on the external disconnecting switch.
nMake sure that on-off remote controls are inhibited.
nWear suitable personal protective equipment (helmet, safety
gloves, goggles and shoes etc.).
To carry out any measurements or checks which require the
activation of the machine:
nWork with the electrical board open only for the necessary time.
nClose the electrical board as soon as the measurement or check
has been completed.
nFor outdoor units, do not carry out any operations in the presence
of dangerous climatic conditions (rain, snow, mist etc.).
The following precautions must be always adopted:
nDo not scatter the fluids of the refrigeration circuit in the
surrounding environment.
nWhen replacing an eprom or electronic cards, use always suitable
devices (extractor, antistatic bracelet, etc.).
nTo replace a compressor, the evaporator, the condensing coils or
any other weighty element, make sure that the lifting equipment is
consistent with the weight to be lifted.
nIn air units with independent compressor compartment, do not
access the fan compartment unless you have disconnected the
machine by the disconnecting switch on the board and you have
placed a warning sign “do not turn on - maintenance in progress”.
nContact manufacturer for any modifications to the refrigeration,
hydraulic or wiring diagram of the unit, as well as to its control
logics.
nContact manufacturer if it is necessary to perform very difficult
disassembly and assembly operations.
nUse only original spare parts purchased directly from manufacturer
or the official retailers of the companies on the recommended
spare parts list.
nContact manufacturer if it is necessary to handle the unit one year
after its positioning on site or if you wish to dismantle it.

6
2 - Safety
2.7 Safety labels
Identification of the refrigerant - External door
Identification of the unit Outside, on the right-hand front column
Pump operation - Outside, on the right-hand front column
LAS BOMBAS MONTADAS EN ESTA UNIDAD NO PUEDEN TRABAJAR SIN AGUA
DIE PUMPEN DIESES GERÄTES DÜRFEN NICHT OHNE WASSER BETRIEBEN WERDEN
THE PUMPS ON BOARD OF THIS UNIT CAN NOT WORK WITHOUT WATER
LES POMPES A BORD DE CETTE UNITE NE PEUVENT PAS FONCTIONNER SANS EAU
LE POMPE ABORDO DI QUESTA UNITÀ NON POSSONO FUNZIONARE SENZA ACQUA
Circuit drain - Outside, on the right-hand front column
Use of filter and flow switch - Adjacent to fittings
È OBBLIGATORIO L’USO DI FILTRO E FLUSSOSTATO ACQUA
THE USE OF FILTER AND FLOW SWITCH IS MANDATORY
EL USO DEL FILTRO Y DEL INTERRUPTOR DE FLUJO ES OBLIGATORIO
L’UTILISATION DU FILTRE ET DU FLUXOSTAT EST OBLIGATOIRE
DER GEBRAUCH VON FILTER UND STRÖMUNGSWÄCHTER IST
VORGESCHRIEBEN
Lifting point - Base Fan Danger
Instruction for the movimentation - Outside the packaging
Electrical warning
Adjacent to the master switch
Pump drain - Outside, on the right-hand front column
USARE SOLO
R 410A
E
RECUPERARE FLUIDO - NON DISPERDERE NELL’AMBIENTE - REGOLAMENTO CEE N° 3093/94
RECOVER - DO NOT VENT - EEC REGULATION N° 3093/94
SPECIAL ESTER OIL
USE ONLY
CODICE PRODOTTO NEUTRO
PRODUCT CODE
MODELLO
MODEL
0425
MO.NO
MATRICOLA
SERIAL NO.
ANNO DI COSTRUZIONE
Manuf. Year
REFR. GWP CIRCUIT 1 2 3 4
CHARGE (Kg)
PS (LATO ALTA / LATO BASSA)
PS (HIGH / LOW SIDE)
TS (ALTA / BASSA)
TS (HIGH / LOW)
ALIM. POTENZA
MAIN SUPPLY
CORRENTE DI SPUNTO
LRA
CORRENTE A PIENO CARICO
FLA
POTENZA ASSORBITA
POWER INPUT
PRESS. MAX ESERCIZIO ACQUA
MAX WATER OPERATING PRESSURE
MASSA
MASS
SYSTEMAIR S.r.l. Via XXV Aprile 29 20825 BARLASSINA MB ITALIA
MADE IN ITALY COD.NO: P35952
MODELLO:
MODEL
MATRICOLA:
SERIAL NO.
CODICE:
PRODUCT CODE
MODELLO:
MODEL
MATRICOLA:
SERIAL NO.
CODICE:
PRODUCT CODE
MODELLO:
MODEL
MATRICOLA:
SERIAL NO.
CODICE:
PRODUCT CODE
bar
°C
V / PH / Hz
(max) A
(max) A
(max) Kw
bar
Kg
ANNO DI COSTRUZIONE
Manuf. Year
ANNO DI COSTRUZIONE
Manuf. Year
ANNO DI COSTRUZIONE
Manuf. Year
(tCO₂eq)
ATTENTION! Don’t leave the unit with water inside hydraulic circuit during
winter or when it is in stand by.
ATTENZIONE! Non lasciare l’unità con acqua nel circuito idraulico durante
l’inverno o quando non è funzionante.
ATTENTION! Ne laissez pas l’unitè avec de l’eau dans le circuit hydraulique
pendant l’hiver ou quand elle ne travaille pas.
WARNUNG! Lassen Sie nicht das Wasser in die Schaltung während des
Winters oder wenn es nicht funktionient.
¡ATENCÍON! No deje el agua en el circuito hidráulico durante el invierno o
cuando no esta trabajando.
ATTENZIONE !
Prima di
aprire togliere
tensione
CAUTION !
Disconnect
electrical
supply before
opening
ACHTUNG !
Vor offnen des
gehauses
hauptschalter
ausschalten
ATENCION !
Cortar la
corrente antes
de abrir
el aparato
ATTENTION !
Enlever
l’alimentation
electrique
avant d’ouvrir
MIN. 5 cm

7
English
2 - Safety
Grounding connection on the
electrical board,
adjacent to the connection
Read the instruction on the
electrical board
Fitting identification - Adjacent to fittings
Sequence phase control on the electrical board
Identification of refrigerant - Below identification of the unit
Parameter configuration - Inside the electrical board
Start-up warning - Outside the door
of the electrical board
Final Test Certificate - Inside the external door
ATTENZIONE
QUESTO COMPRESSORE RICHIEDE UN CORRETTO
SENSO DI ROTAZIONE RISPETTARE LA CORRETTA
SEQUENZA DELLE FASI.
THIS COMPRESSOR REQUIRES PROPER DIRECTION
OF ROTATION CHECK PROPER ELECTRICAL PHASING
CAUTION
KOMPRESSOREN BENÖTIGEN KORREKTES DREHFELD
ELEKTRISCHE ANSCHLÜSSE AUF DREHFELD ÜBERPRÜFEN
ACHTUNG
CES COMPRESSEURS NECESSITENT UN BON SENS
DE ROTATION VERIFIER LE CABLAGE DES PHASES
ATTENTION
ESTOS COMPRESORES DEBEN FUNCIONAR EN
EL SENTIDO DE ROTACIÓN CORRECTO COMPROBAR
EL CABLEADO DE LAS FASES
ATENCIÓN

8
2 - Safety
REFRIGERANT DATA SAFETY DATA: R410A
Toxicity Low.
Contact with skin
If sprayed, the refrigerant is likely to cause frost burns. If absorbed by the skin, the danger is very limited;
it may cause a slight irritation, and the liquid is degreasing. Unfreeze the affected skin with water.
Remove the contaminated clothes with great care - in the presence of frost burns, the clothes may stick
to the skin. Wash with plenty of warm water the affected skin.
In the presence of symptoms such as irritation or blisters, obtain medical attention.
Contact with eyes
Vapours do not cause harmful effects. The spraying of refrigerant may cause frost burns.
Wash immediately with a proper solution or with tap water for at least 10 minutes, and then obtain
medical attention.
Ingestion
Very unlikely - should something happen, it will cause frost burns.
Do not induce vomiting. Only if the patient is conscious, wash out mouth with water and give some
250 ml of water to drink. Then, obtain medical attention.
Inhalation
R410A: remarkable concentrations in the air may have an anaesthetic effect, up to fainting.
The exposure to considerable amounts may cause irregular heartbeat, up to the sudden death of the
patient. Very high concentrations may result in the risk of asphyxia, due to the reduction in the oxygen
percentage in the atmosphere. Remove the patient to fresh air and keep warm and at rest.
If necessary, give oxygen. In case of breathing difficulties or arrest, proceed with artificial respiration.
In case of cardiac arrest, proceed with cardiac massage. Then, obtain medical attention.
Recommendations Semiotics or support therapy is recommended. Cardiac sensitisation has been observed that, in the presence of circulating catecholamines such as adrenalin, may cause cardiac arrhythmia and
accordingly, in case of exposure to high concentrations, cardiac arrest.
Prolonged exposure
R410A: a study on the effects of exposure to 50,000 ppm during the whole life of rats has identified the
development of benign testicle tumour.
This situation should therefore be negligible for personnel exposed to concentrations equal to or lower
than professional levels.
Professional levels R410A: Recommended threshold: 1000 ppm v/v - 8 hours TWA.
Stability R410A: Not specified.
Conditions to avoid Do not use in the presence of flames, burning surfaces and excess humidity.
Hazardous reactions May react with sodium, potassium, barium and other alkaline metals.
Incompatible substances: magnesium and alloys with magnesium concentrations > 2%.
Hazardous decomposition
products R410A: Halogen acids produced by thermal decomposition and hydrolysis.
2.8 Safety regulations

9
English
2 - Safety
REFRIGERANT DATA SAFETY DATA: R410A
General precautions
Do not inhale concentrated vapours. Their concentration in the atmosphere should not exceed the
minimum preset values and should be maintained below the professional threshold. Being more weighty
than the air, the vapour concentrates on the bottom, in narrow areas. Therefore, the exhaust system must
work at low level.
Respiratory system protection
If you are in doubt about the concentration in the atmosphere, it is recommended to wear a respirator
approved by an accident-prevention
Authority, of the independent or oxygen type.
Storage
Cylinders must be stored in a dry and fresh place, free from any fire hazard, far from direct sunlight or
other sources of heat, radiators etc.
Keep a temperature below 50 °C.
Protective clothing Wear overalls, protective gloves and goggles or a mask.
Accidental release measures
It is important to wear protective clothing and a respirator.
Stop the source of the leak, if you can do this without danger. Negligible leaks can be left evaporating
under the sun, providing that the room is well ventilated.
Considerable leaks: ventilate the room. Reduce the leak with sand, earth or other absorbing substances.
Make sure that the liquid does is not channelled into gutters, sewers or pits where the vapours are likely
to create a stuffy atmosphere.
Disposal The best method is recovery and recycling. If this method is not practicable, dispose according to an
approved procedure, that shall ensure the absorption and neutralization of acids and toxic agents.
Fire fighting information R410A: Not flammable in the atmosphere.
Cylinders The cylinders, if exposed to fire, shall be cooled by water jets; otherwise, if heated, they may explode.
Protective fire fighting equipment In case of fire, wear an independent respirator and protective clothing.
2.8 Safety regulations (continued)

10
2 - Safety
LUBRICANT OIL DATA SAFETY DATA: POLYESTER OIL (POE)
Classification Not harmful.
Contact with skin
May cause slight irritation. Does not require first aid measures. It is recommended to follow usual
personal hygiene measures, including washing the exposed skin with soap and water several times a day.
It is also recommended to wash your overalls at least once a week.
Contact with eyes Wash thoroughly with a suitable solution or tap water.
Ingestion Seek medical advice immediately.
Inhalation Seek medical advice immediately.
Conditions to avoid Strong oxidising substances, caustic or acid solutions, excess heat.
May corrode some types of paint or rubber.
Protection of the
respiratory system Use in well ventilated rooms.
Protective clothing Always wear protective goggles or a mask. Wearing protective gloves is not mandatory, but is
recommended in case of prolonged exposure to refrigerant oil.
Accidental release measures
It is important to wear protective clothing and, especially, goggles.
Stop the source of the leak. Reduce the leak with absorbing substances (sand, sawdust or any other
absorbing material available on the market).
Disposal The refrigerant oil and its waste will be disposed of in an approved incinerator, in conformity with the
provisions and the local regulations applicable to oil waste.
Fire fighting information In the presence of hot liquid or flames, use dry powder, carbon dioxide or foam. If the leak is not burning,
use a water jet to remove any vapours and to protect the personnel responsible for stopping the leak.
Cylinders The cylinders exposed to a fire will be cooled with water jets in case of fire.
Fire fighting protective equipment In case of fire, wear an independent respirator.
2.8 Safety regulations (continued)

11
English
3 - Transport, Handling and Storage
SYSCROLL AIR EVO HP units are supplied fully assembled and tested
(except for accessories supplied loose in the units – absorbers, filter,
etc.). They are ready to be installed and started on the field.
R410A units are only charged with liquid refrigerant and with oil in the
quantity required for operation.
WARNING
The low pressure side of the refrigerating circuit
on R410A units shall be charged by means
of the service valve arranged on the thermal
expansion valve before the device is operated.
3.1 Inspection
The unit shall be immediately inspected upon receipt to find out any
damage since it has been delivered ex works and transported at the
customer’s risk. It is also necessary to make sure that all the parcels
specified on the delivery note have been delivered.
Any damage you may find out shall be immediately reported in writing
to the carrier. Even if the damage is only on the surface, please notify
our local representative too.
The manufacturer disclaims all responsibility for the shipment even if
it has provided for its organisation.
3.2 Handling
SYSCROLL AIR EVO HP units are designed to be lifted from above, by
means of cables and eyebolts. A spacer shall be arranged between
the cables in order to prevent them from damaging the unit (see the
figure aside).
Before handling the devices, make sure the site you have chosen for
the installation can withstand its weight and support its mechanical
impact.
Avoid touching sharp parts (such as the fins of batteries, for example)
while handling the unit.
WARNING
The unit shall never be placed on rollers.
Act as follows to lift and handle the unit:
nInsert and secure the eyebolts into the frame holes which have
been marked on purpose.
nConnect the cables to the eyebolts.
nInsert the spacer between the cables.
nProvide for hooking at the centre of gravity of the device.
nCables shall have such a length that the angle they form with the
horizon when under tension is not less than 45°.
Holes Ø 30 mm
WARNING
While lifting and handling the unit, pay attention.
Otherwise, you might damage the finned block of
the coils arranged on both sides of the unit. The
sides of the unit shall be protected by cardboard
or plywood sheets.
Space requirements request to handling
MIN. 5 cm
SOLLEVAMENTO SYSCL 20-35
MIN. 5 cm

12
3 - Transport, Handling and Storage
WARNING
Until the unit is ready for operation, do not
remove the plastic envelope and the coil
protections which are intended to prevent dirt,
dust and any foreign matter from penetrating
into the unit through the inlets of fans or from
damaging the external surfaces.
3.3 Anchoring
It is not essential to secure the unit to the foundations, unless in areas
where there is a serious risk of earth-quake, or if the appliance is
installed on the top of a steel frame.
3.4 Storage
If the unit is to be stored before the installation for some time, take
at least the following precautions to prevent damage, corrosion and/
or deterioration:
nMake sure all openings, such as for example water connections,
are well plugged and sealed.
nNever store the units in a room where temperature is above
50 °C (R410A units) or where the units are directly exposed to
the sunlight.
nMinimum storage temperature is -25 °C.
nIt is recommended to leave the finned coils covered to protect
them against any risk of corrosion, especially if building works
are still in progress.
nStore the units in areas where minimum activity is likely to take
place in order to avoid any risk of accidental damage.
nNever use steam to clean the unit.
nRemove all the keys required to have access to the control panel
and give them to the person in charge of the field.
It is also recommended to provide for visual inspections at regular
intervals.

13
English
4 - Installation
4.1 Installation Site
DANGER
Before installing the unit, make sure that
the building structure and/or the supporting
surface can withstand the weight of the
device. The weights of the units are detailed
by Chapter 9 of this manual.
These units have been designed to be installed on the floor, in the
open air. As a standard, they are equipped with rubber vibration-
damping supports which shall be arranged in the middle, beneath
the supporting plates.
When the unit is to be installed on the ground, provide for a concrete
bedplate which shall assure a uniform distribution of the weights. No
special subbase is generally required.
When selecting the installation site, never forget to consider as
follows:
nThe longitudinal axis of the unit shall be parallel to the direction of
the prevailing winds so as to assure a uniform air distribution on
finned exchangers.
nThe unit shall never be installed in the proximity of chimneys for
the discharge of boiler flue gases.
nThe unit shall never be installed downwind of sources of grease
contaminated air, such as for example the outlets of large-
kitchen extractors. Otherwise, grease might build up on the fins
of refrigerant / air exchangers or condensers, act as a fixing
agent for any sort of atmospheric impurity and rapidly cause the
exchangers to clog.
nThe unit shall never be installed in areas exposed to heavy
snowfalls.
nThe unit shall never be installed in areas exposed to flooding or
beneath drip stones, etc.
nThe unit shall never be installed in narrow inner court yards or in
any other restricted space where the noise may be reflected by
the walls or where the air expelled by the fans may short-circuit
on the refrigerant/air heat exchangers or condensers.
nThe installation site shall be characterised by the presence of
the space required for air circulation and for the performance of
maintenance operations (see chapter 9 for further details).
4.2 External Water Circuit
WARNING
The external water circuit shall guarantee a
constant water flow rate through the circulating
refrigerant/water heat exchanger (evaporator)
under steady operating conditions and in case
of a load variation.
The circuit shall be composed by the following elements:
nA circulation pump which can ensure the necessary flow rate and
head.
nThe total content of the primary water circuit shall never be
lower than 2.5 lt/kW in terms of refrigerating capacity. If the total
water volume in the primary circuit should be unable to reach
such a value, an additional heat-insulated storage tank should be
installed. This tank is intended to avoid any repetitive start of the
compressor.
nA membrane expansion tank complete with a safety valve and a
drain which shall be visible.
NOTE
The expansion tank shall be dimensioned in
such a way that it can absorb a 2% expansion
of the total volume of the water in the plant
(exchanger, pipelines, uses and storage tank,
if available). The expansion tank shall never
be insulated when the circulating fluid is not
flowing through it.
A differential pressure switch is mounted as a standard. It will stop
the unit whenever it senses a load loss through the heat exchanger
which may result in a flow rate problem.
In addition:
nInstall on/off valves (accessory) on the lines at the inlet and outlet
of the manifolds of the exchangers (evaporator).
nArrange a by-pass complete with an on/off valve between the
manifolds of the heat exchangers.
nArrange air vent valves at the high points of the water lines.
nArrange drain points complete with plugs, clocks, etc. in the
proximity of the low points of the water lines.
nInsulate the water lines to prevent the heat from blowing back into
the unit.

14
4 - Installation
WARNING
Before filling the installation, remove any
impurity, such as sand, crushed stones and
welding scales, coating drops and any other
material which might damage the evaporator.
It is advisable to flush with disposable water bypassing the exchanger
to avoid clogging.
NOTE
The water used to fill the circuit shall be treated
in such as way that the pH will have the correct
value.
When two or several units are connected in parallel, to balance the
load losses of the various circuits, it is recommended to execute a
“reverse return” connection (see the diagram below).
External water circuit
SAFETY/CONTROL DEVICES
AInlet water temperature sensor
BOutlet water temperature sensor
CWater differential pressure switch (105 mbar)
DVent valve
EWater safety valve (3 bar)
FManometer
FS Flow switch
GThermometer
Unit side
YWater drain
COMPONENTS
1Plate heat exchanger
2Pump
3Draining valve
4Water buffer tank
5Water filter
6Automatic water charging valve
7Pressure expansion tank
8Water charging line
9Water outlet
10 Water inlet
11 Globe valve
12 Flexible pipes
13 By-pass valve
UNIT 1
UNIT 2
Legend
S On/Off valves
VG Balancing valves

15
English
4 - Installation
4.3 Water connections
The flow switch and the filter water, although not included in the
supply, must always be fitted such as plant components.
Their installation is mandatory for warranty.
WARNING
The attachments at the water inlet and outlet
shall be connected in compliance with the
instructions which can be found on the labels in
the proximity of the attachments.
Connect the water lines of the plants with the attachments of the unit
whose diameters and positions are shown in Chapter 9.
4.4 Defrost water drainage
When heat pump units work in heating mode, during defrosting
cycles, they may discharge water from the base. This is why the
units should be installed at least 200 mm above the floor level, so
as to allow the free drainage of waste water, without the risk of
producing ice banks.
The heat pump units must be installed in positions where the
defrosting water cannot create any damage.
4.5 Water buffer tank
The accumulation tank which has been designed to be mounted on
units is complete with all the hydraulic and electrical components
required for the correct operation of the system.
These systems are carefully assembled and tested at works. They
are ready for operation after having correctly realised all electrical
and hydraulic connections.
WARNING
Don’t leave the unit with water inside the circuit
during the winter or when it is in stand by,
unless water is properly mixed with glycol.
4.5.1 Features
Units have one single tank. The kit will include an Antifreeze Electric
Heater, a drain valve, an automatic filling unit and an automatic air
vent.
No pump is arranged on the kit since it is mounted on the unit.
A tank arranged for mounting a heating booster resistance kit may be
optionally required (5 traps).
The tank is completely insulated with 30 Kg/m3closed cell
polyethylene in a silver colour and enclosed by a bearing structure
made of passivated and painted plates. The box is equipped with
bulkheads which can be easily opened for internal inspection.
The kit is installed beneath the unit. It is an integral part of the unit
without changing the support area.
4.5.2 Supplied Material
The kits will be supplied with pipelines ready for installation. An
antifreeze resistance with wiring, an automatic water filling valve, a
3 bar safety valve, a drain valve and a vent valve have already been
assembled.
Hydrokit is shipped with a film to protect it from atmospheric agents.
Packaging has been designed in order to stack it up.
4.5.3 Antifreeze Electric Heater
The antifreeze resistance of the tank (TEH) shall be wired with the
panel as it is shown by the diagram attached to the unit.
4.5.4 Water Filter
The kit will use the water filter of the unit.
RECOMMENDED WATER COMPOSITION
PH 7,5 - 9
Electrical conductivity 10 - 500 μS/cm
Total hardness 4,5 - 8,5 dH
Temperature < 60 [°C]
Alkalinity (HCO3-) 70-300 ppm
Alkalinity / Sulphates (HCO3-/ SO42-) > 1 ppm
Sulphates (SO42-) < 70 ppm
Chlorides (Cl-) < 50 ppm
Free Chlorine < 0,5 ppm
Phosphates (PO43-) < 2 ppm
Ammonia (NH3) < 0,5 ppm
Ammonium Ion (NH4+) < 2 ppm
Manganese Ion (Mn2+) < 0,05 ppm
Free Carbon Dioxide (CO2) < 5 ppm
Hydrogen Sufide (H2S) < 0,05 ppm
Oxygen Content < 0,1 ppm
Nitrates (NO3-) < 100 ppm
Manganese (Mn) < 0,1 ppm
Iron (Fe) < 0,2 ppm
Aluminium (Al) < 0,2 ppm
Caution
If the water circuit is to be drained for a time exceeding one month, the
circuit must be fully charged with nitrogen to prevent any risk of corrosion
by differential venting

16
4.6 Power supply
DANGER
Before carrying out any operations on the
electrical system, make sure that the unit is
deenergized.
DANGER
It is important that the appliance is grounded.
WARNING
The company in charge of the installation shall
conform to the standards applicable to outdoor
electrical connections.
The manufacturer may not be held liable for any damage
and/or injury caused by failure to comply with these
precautions.
The unit conforms to EN 60204-1.
The following connections shall be provided:
nA 3-phase and grounding connection for the power supply circuit.
nThe electrical distribution system shall meet the power absorbed
by the appliance.
nThe disconnecting and magnetothermal switches must be sized
to control the starting current of the unit.
nThe power supply lines and the insulation devices must be
designed in such a way that every line independent.
nIt is recommended to install differential switches, to prevent any
damage caused by phase drops.
nThe fans and compressors are supplied through contactors
controlled from the control panel.
nEach motor is provided with an internal safety thermal device and
external fuses.
nThe power supply cables must be inserted into dedicated
openings on the front of the unit, and the will enter the electrical
board through holes drilled on the bottom of the board.
4 - Installation
CAUTIONS
The unit + tank system shall be equipped with a filter. Use the filter
+ union as it is shown by Figure 1.
4.5.5 Installation Procedure
The hydrokit shall be arranged beneath the unit. It will not change its
overall dimensions (Figure 1).
Arrange the rubber shock absorbers beneath the kit before providing
for its connection.
Provide for the hydraulic and electrical connections. Doing that,
observe the diameters shown by the quoted drawings.
The wiring for the standard antifreeze resistance is arranged as it is
shown by . The resistance is connected with the main terminal box.
See the wiring diagram attached to the unit for the correct execution
of the electrical connections.
Install the water filter as it is shown by Figure 1.
Figure 1

17
English
Antifreeze
Resistance Wiring
Storage Kit (112 l) - Dimensional Data
4 - Installation
1352
4 holes Ø9
1477
92213 195
62.5 62.5
33 33434
390
186
200106
43
500
A
C
B
Front view Side view
Top view
AWater inlet on the plant side Ø1 ½” gas male
BWater outlet on the chiller side Ø1 ½” gas male
CWater filling ؽ” gas male

18
4 - Installation
4.7 Electrical connections
The unit must be installed on site according to the usual
procedures and standards applicable in the place of
installation. The unit must not be operated if its installation
has not been carried out according to the instructions
provided in this manual.
The power supply lines must consist of insulated copper
conductors, dimensioned for the maximum absorbed
current.
Connection to terminals must be performed according to the diagram
of connections (User’s Terminal Box) provided in this manual and
according to the wiring diagram which accompanies the unit.
WARNING
Before connecting the power supply lines, check
that the available voltage value does not exceed
the range specified in the Electric Data (Chapter
9).
For 3-phase systems, check also that the unbalance between the
phases does not exceed 2%. To perform this check, measure the
differences between the voltage of each phase couple and their mean
value during operation. The maximum % value of these differences
(unbalance) must not exceed 2% of the mean voltage.
If the unbalance is unacceptable, contact the Energy Distributor to
solve this problem.
WARNING
Supplying the unit through a line whose
unbalance exceeds the permissible value will
automatically void the warranty.
The unit conforms to EN 61000-3-12: Electromagnetic compatibility
(EMC) Part 3-12: Limits - Limits for harmonic currents produced
by equipment connected to public low voltage systems with input
current ›16 A and ←75 A per phase. Conformity depends on public
mains power supply with short-circuit power Ssc ≥1.9MVA at the
point of connection (see table 4 of the standard with Rsce ≥120).

19
English
Electrical Connections
4 - Installation