Takstar TA-60 User manual

单体：动圈式
指向性：超心型
频率响应：60Hz-18KHz
灵敏度：-51dB±3dB（0dB=1V/Pa at 1KHz）
输出阻抗：350Ω±30%（at 1KHz）
350g
○
○
○
○
○
○ 净重：
产品特性
尊敬的用户：
感谢您选购TAKSTAR TA-60动圈式麦克风，为了您能够更好的了
解使用本产品，建议您在使用前仔细阅读本说明书。
若存在有疑问或者您有宝贵的建议，
可通过拨打得
胜官方服务热线 400 6828 333 或使用微信扫描二维码
关注得胜官方公众号与我们联系。
专业动圈麦克风
○
○
○
○
○
锌合金本体及铜焊网头，全金属设计，时尚耐用
超心型指向拾音，防喷麦设计，低啸叫，高增益
特设音头防震架，有效防止手持噪音，保障拾音效果
频响宽，高还原，不失真，适应不同场合使用
磁簧开关设计，避免开关冲击声，保护后级设备
技术参数
频率响应曲线图
Hypercardioid
(at 1kHz)
0°
330°
300°
240°
210°
30°
60°
90°
120°
150°
180°
270°
邮编：516121
广东省电声工程技术研究开发中心
广东省得胜电子有限公司制造
地址：广东省惠州市博罗县龙溪镇富康一路2号 全国服务热线：400 6828 333
传真：[phone]
邮箱：[e-mail] 扫一扫，了解更多产品
扬声器
话筒
声源
调音台
卡侬
麦克风
扣键
麦克风线材
安装使用
※本产品相关规格如有变更恕不另行通知。
1. 麦克风与线材连接时，将线材卡侬对准麦克风尾部三针插入，直到
卡侬上的扣键“哒”的一声定位；
2. 麦克风与线材分离时，握住卡侬并按压卡侬扣键，将线材拔出；
3. 将麦克风线材另一端与调音台、功放、声卡等设备连接；
4. 使用时应先将设备音量调小，再将音量从小到大慢慢调节至合适，
以免声压过大对扬声器产生冲击；
5. 手不要握在麦克风网头上，尽可能的拉开麦克风与扬声器的距离，
避免麦克风和扬声器相对，以免影响麦克风音质及有效控制回馈啸
叫。
为避免电击、过高温度、着火、辐射、爆炸、机械危险以及使用
不当等可能造成的人身伤害或财产损失，使用本产品前，请仔细阅读
并遵守以下事项：
1. 使用产品时请合理调整音量大小，不要在大音量下长时间使用，以
免造成耳朵听力损伤；
2. 使用中若发现有异常（如冒烟、异味等），请立即关闭电源开关并
拔掉电源插头，然后将产品送经销商检修；
3. 本产品及附件都应放置在室内干燥通风处，勿长期存放在潮湿、灰
尘多的环境，使用中避免碰到液体物质、雨淋、产品进水、过度碰
撞、抛掷、振动本机及覆盖通风孔，以免损坏其功能；
4. 若产品需要固定于墙壁或天花板上时，请确保固定到位，防止因固
定强度不足导致产品发生跌落危险；
5. 使用该产品时需遵守相关安全规定，法律法规明确禁止使用场合请
勿使用本机，以免导致意外事故；
6. 请不要自行拆机改装或维修，以防止出现人身伤害，如有问题或服
务需求请联系当地经销商跟进处理；
Frequency Response Graph
-80
TA-60

Features
Specification
Frequency Response Curve
Hypercardioid
(at 1kHz)
0°
330°
300°
240°
210°
30°
60°
90°
120°
150°
180°
270°
Frequency Response Graph
-80
Dear Customer,
Thank you for purchasing TAKSTAR TA-60
Please read the user manual before operation.
If you have any question or suggestion, please dial contact us.
dynamic microphone.
○
○
○
○
○
Rugged zinc alloy structure and metal grille, fashionable and
durable design
Super cardioid pickup, pop-noise-resistant design, low feedback
and high gain
Capsule shock mount design prevents handling noise and ensures
the excellent pickup effect
Wide frequency response, natural reproduction without distortion
Magnetic-reed switch design prevents ON/OFF surge noise and
protects the rear equipments
○
○
○
○
○
○
Transducer Principle: Dynamic
Polar Pattern: Super cardioid
Frequency Response: 60Hz-18kHz
Sensitivity: -51dB±3dB (0dB=1V/Pa at 1kHz)
Output Impedance: 350Ω±30% (at 1kHz)
Net Weight: 350g
Professional Dynamic Microphone
speaker
microphone
audio source
mixer
XLR
microphone
button
microphone cable
※The product specification is subject to change without prior notice.
1. When connecting the microphone with cable, match the XLR
connector with the 3 pin on microphone, then insert fully till the
XLR lock button fixes the position.
2. When disconnecting the microphone with the cable, press the XLR
lock button, then take out the cable.
3. Connect the other end of the cable with the equipments, e.g. mixer,
power amplifier, sound card.
4. Reduce the equipment volume before operation, then adjust the
volume to a proper level to avoid speaker damage by the sound
pressure surge.
5. Do not hold the microphone grille. Keep the microphone away from
the speaker as much as possible and avoid the capsule pointing to
the speaker to prevent from feedback.
Installation
To avoid personal injury or property loss caused by electric shock,
over temperature, fire, radiation, explosion, mechanical risk and
improper use, please read carefully and abide by the following
items before operation:
1. Please check if the power of the connected equipment matches with
that of this product before operation. Adjust the volume to proper
level during operation. Do not operate at over-power or high volume
level for a long time to avoid abnormal functioning or hearing loss.
2. If abnormal phenomenon (smoke, abnormal smell) happens, please
turn off the power switch and disconnect the power plug with power
socket, and send the product to local dealer for maintenance.
3. The product and accessories should be put in dry and ventilated
place rather than humid or dusty environment. Prevent the product
from fire, liquid, rain, water, over-colliding, throwing, vibrating, vent
hole covered to avoid function damage.
4. When the product needs to be installed on wall or ceiling, please fix
it tightly to avoid dropping risk.
5. Please abide by safety rules during operation. Do not use the product
in the place prohibited by regulation or law to avoid accident.
6. Do not disassemble or repair the product by yourself to avoid
personal injury. If you have question or need service, please contact
the local dealer.
Caution
Guangdong Takstar Electronic Co., Ltd.
Address: No. 2 Fu Kang Yi Rd., Longxi Boluo Huizhou, Guangdong 516121 China
Tel: [phone] Fax: [phone] Website: www.takstar.com
E-mail: [e-mail]
TA-60