Tally Dascom 7106 User manual

– 1 –
Installation Guide 7106 7206
User Guide Peeler Unit

– 2 –
©
August 2010 DASCOM Europe GmbH

– 3 –
Installation Guide
0 The following installation shows a 7106 printer. The peeler installation for 7206
printers follows the same steps.
1 Before installing the Peeler Unit
1-1 Remove the plastic front cover on the front side of the printer upward as shown
below.
Be careful that you do not touch other parts when removing the front cover.
1-2 Remove the screw (M3 X 6) of the motor cover and take the motor cover out
as shown below.
Remove the
screw and the
motor cover

– 4 –
1-3 Remove the screw (M3 X8, for plastic) and take the connector cover out as
shown below.
2 Installing the peeler
2-1 While inserting the peeler cable in the space (A) between the paper feed motor
and the printer housing, match the protruded pins of the peeler unit to the ho-
les of the front of the mechanism unit.
Set the peeler unit to the printer using the accessory screws (3 pcs M3 X 6)
enclosed.
Remove the
screw and the
connector cover
Set 3 pcs screws
(M3X6)

– 5 –
2-2 Connecting the peeler unit cable
Connect the peeler unit cable connector to the receptacle of the printer after
setting the peeler cable in the printer housing.
Note: Set the peeler cable (A) not to touch the print head-up spring (B) of the me-
chanism unit.
It is allowed to set the peeler cable under the paper feed motor instead of
the side of the paper feed motor.
AA
B

– 6 –
3 Reinstalling the covers
Reinstall the connector cover (M3 X 8, for Plastic) and the motor cover
(M3 X 6).
Note: Keep the front cover for future use which you remove the peeler unit.
Note: Use specified screw for the covers.
Do not use wrong type screw, otherwise the screw hole of the printer hou-
sing will be damaged.
Motor cover
Connector cover

– 7 –
User Guide
Contents
Caution ･････････････････････････････････････････････････････ 8
1 Outline ･･････････････････････････････････････････････････ 9
2 Exterior view and part names･･･････････････････････････････ 9
3 How to operate ･･･････････････････････････････････････････ 10
3-1 Operation
････････････････････････････････････････････ 10
3-1-1 Peeler door opening/closing ･････････････････････ 10
3-1-2 Media loading･･････････････････････････････････ 10
3-1-3 Peeler setting ･･････････････････････････････････ 10
3-1-4 Initial value of peeling position ･･･････････････････ 11
3-1-5 Peeler commands ･･････････････････････････････ 12
4 Peeler specifications ･･････････････････････････････････････ 13

– 8 –
Caution
Company names and product names in this manual are trademarks or
registered trademarks of relevant companies.
CAUTION
Always use the peeler with the door closed except when the media
is loaded into the peeler.
Do not push down the door roughly when it is opened, which may
cause damage to the hinge of the door.
Use the media that meets standard requirements. If not, the liner
and label may be jammed in the peeler.
Wipe off dirt or glue stuck to the peeler with a soft cloth soaked in
a neutral detergent.
Do not use volatile liquids such as benzine and thinner, which may
cause the roller rubber and plastic parts to deteriorate.

– 9 –
1 Outline/2 Exterior view and part names
1 Outline
This peeler unit is designed to automatically remove the label from the liner.
2 Exterior view and part names
Peeling Roller
Idle Roller (upper)
Friction Roller (lower)
Doo
r
Peeling Senso
r
Release Knob
Front view
Top view
Top view of door opened
Side view

– 10 –
3 How to operate
3-1 Operation
3 How to operate
3-1 Operation
3-1-1 Peeler door opening/closing
(1) Opening
Shift the release knob of the peeler to the left with the finger, and the peeler door
will open.
(2) Closing
Push down the left end of the peeler door until it clicks closed.
3-1-2 Media loading
(1) First peel off the labels with a length of 12cm (5 inch) or more on the top of the
loading media, then load the media into the peeler where the first label comes to
the peeling sensor. Close the print head of the printer.
(2) Open the peeler door and pass the liner between the peeling roller and the peeler
door and close the door.
3-1-3 Peeler setting
To use this peeler, set the peeler function ON that is one of the various setting items in
a nonvolatile memory in the printer.
To change the setting of the peeler function, execute it in the printer configurations
setting mode from the control panel or use the command STX KD.
The printers have the menu “AutoConfigure“ set to ON when shipping from the
factory. In this ON condition, if the peeler is installed on the printer, the menu “Function
Select” will be automatically changed to “Peel On.” But if the Off condition occurs, select
the “Peel On” in the following manner. (For details of menu setting, refer to the operation
manual of each printer.)

– 11 –
3 How to operate
3-1 Operation
3-1-4 Initial value of peeling position
The paper position for peeling off the label can be adjusted in the printers menu. See
an excerpt of the printer menu and the web panel.
To adjust the peeling position, designate the feeding amount from the reference
point to the peeling position with the command STX f or STX Kf. The value with
this command will be effective until the resetting is performed. (For details, see the
separate Command Reference.)
Liner
Peeling plate
Center of platen
Sensor reference point
Label
f = 256 (2.56 in, 65.00 mm)
9.1 mm
(0.36 in)
Middle point
between labels
55.9 mm (2.2 in)

– 12 –
3 How to operate
3-1 Operation
3-1-5 Peeler commands
The following are the peeler commands. For details of each command, see the
separate Command Reference.
Peeling position designated command STX f, STX Kf
This command designates the feeding amount from the reference point to the
peeling position.
Software switch setting command STX V
This command temporarily changes the contents of the option function setting in a
nonvolatile memory in the printer. With this command, the peeler function is turned
ON or OFF temporarily.
Note: If the label is at peeling position when the peeler function is selected, the
medial will not feed even if the Feed key is pressed. In this case, remove
the label first.

– 13 –
4 Peeler specifications
4 Peeler specifications
Width of liner (a) : 1 −4.65 in (25.4 −118 mm)
Length of label (b) : 1 −4.72 in (25.4 −120 mm)
Label: fine media/Thickness: 0.09 mm
(including glue layer)/Rolled inwards
Minimum width of label (c) : Label must be positioned at 0.63 −0.87in
(16 −22 mm) from left edge of liner,
which is viewed from front of media exit
Maximum width of label : To be narrower than liner
Thickness of label : 0.0067 in (0.17 mm) or less
Thickness of liner : 0.0027 in (0.07 mm) or less
Maximum diameter of roll media : 8 in (203 mm)
Inner diameter of roll media : 3 in (76 mm) or more
gnisunehw(slebaldeleepnoillimenoromk001:ytilibaruD
the label above)
Peeling position accuracy : ±1.0 mm
Peeling position varies depending on the type of
media, the size of roll media and the size of ink
ribbon, so adjust it to the optimum condition as
needed
c
a
b
Direction of media feed

© August 2010 DASCOM Europe GmbH v1.0
For sales or technical support call The Printer Place
Tel.: [phone] www.theprinterplace.com