T&S MV-1907-01 User manual

Installationand
Maintenance
Instructions
Washdown Stations
MV-1907-01 & B-1455-01
Deutsch: Installations- und
Wartungsanleitungen
Español: la Instalación y las
Instrucciones de
Mantenimiento
Français: les Instructions
d’Installation et
d’Entretien
Limited One Year Warranty
T&S warrants to the original purchaser (other
than for purposes of resale) that such product is
free from defects in material and workmanship
for a period of one (1) year from the date of pur-
chase. During this one-year warranty period, if
theproductisfoundtobedefective,T&Sshall,at
itsoptions,repairand/orreplaceit. Toobtainwar-
rantyservice,products mustbereturned to...
T&S Brass and Bronze Works, Inc.
Attn: WarrantyRepairDepartment
2 Saddleback Cove
TravelersRest, SC 29690
Shipping, freight, insurance, and other trans-
portationcharges of the product to T&S and the
returnofrepaired orreplaced productto thepur-
chaser are the responsibility of the purchaser.
Repair and/or replacement shall be made within
areasonable time after receipt by T&S of the re-
turned product. This warranty does not cover
Items which have received secondary finishing
orhave been alteredor modified afterpurchase,
orfordefects causedbyphysicalabusetoormis-
useoftheproduct, orshipmentofthe products.
Anyexpresswarrantynotprovidedherein,and
any remedy for Breach of Contract which might
arise, is hereby excluded and disclaimed. Any
impliedwarrantiesofmerchantabilityorfitnessfor
a particular purpose are limited to one year in
duration. Under no circumstances shall T&S be
liablefor lossof useor anyspecial consequential
costs,expensesordamages.
Some states do not allow limitations on how
long and implied warranty lasts or the exclusion
or limitation of incidental or consequential dam-
ages,so the above limitationsor exclusions may
not apply to you. Specific rights under this war-
rantyand otherrights vary fromstate tostate.
P/N: 098-006165-45 Rev. 3
Date: 990318
Drawn: CW
Checked: MAB 8-10-99
Approved: MVW 8-6-99

Exploded View
*
Some items are listed for instructional
purposes and may not be sold as separate parts.
11
12
13
Side
View
Existing piping
supplied by
others
7
8
3
2
1
4
9
10
6
5
2

Part Number Guide
Washdown Station Assembly
1Coupling, 1/2" IPS FE Hex Inlet *
2Valve, 1/2" Globe 006647-25
3Thermometer, 50-500 w/T&S Logo 002971-45
4Asm, Washdown Station, SW 1/2" C 005265-25
5Elbow, 1/2" 001357-40
6Nipple, Outlet 001509-40
7Asm, Hose 1/2" 002969-40
8Water Gun 002967-45
9Asm, Wall Bracket 1/2" Pipe B-0110
10 Bracket, Hose 002970-45
11 Spacer, Hose Rack 003084-45
12 Screw, Hex Cap 003076-45
13 Shield, Anchor Bracket 003077-45
3

4
General Instructions
Installation:
Note: Before installing valve, flush
out all supply lines.
1. Screw no.1onto bottom of existing
supply piping, use Teflon tape or pipe
joint compound on threads. No.2
should face towards front.
3. Connect no.6to no.7, use Teflon
tape on threaded end of no.6.
2. Screw no.3 into opening of no.4,
use Teflon tape (Do Not Use Loctite
on threads, as no.3may need to be
replaced at a later date.)
1
2
close view of
no.10
installation
8”
existing piping
supplied by others
3
4
13
11
10
12
6
10
4. Mount no.10 to wall (in a
convieneint location) withno.12 and
no.13, or other appropriate means.
No.11 is provided by T&S Brass
6
5. Turn on water supply and check
for leaks.
7
Note: T&S recommends install-
ing the B-0110 wall brackets
supplied with this model.

5
Instrucciones
Generales
Instalación:
Nota: Fluya todas las líneas de
surtido, antes de instalar la válvula.
1. Atornille la parte No.1a la parte de
abajo de la tubería surtidora existente,
utilice cinta de Teflon o compuesto de
coyuntura en las roscas. La parte No.2
debe ser orientada hacia el frente.
3. Conecte la parte No.6 a la parte
No.7, utilice cinta de Teflon en el
extremo con roscas de la parte No.6.
2. Atornille la parte No.3dentro de la
abertura de la parte No.4, utilice
cinta de Teflon. (No utilice Loctite
en las roscas, en caso de que la parte
No.3tenga que ser reemplazada en el
futuro).
1
2
Vista amplia de
la instalación de
la parte No.10
8”
Tuberíaexistente es
surtida por otros
3
4
13
11
10
12
6
10
4. Monte la parte No.10 a la pared
(en un sitio conveniente) con las
partes No.12 y No.13, o otros
métodos apropiados. La parte No.11
es surtida por T&S Brass.
6
5. Abra la fuente de agua e
inspeccione por filtraciones.
7
Nota: T&S recomienda que instale
la ménsula de pared B-0110 surtida
coneste modelo.

6
Instructions
Générales
L’Installation:
Noter: Avant installer la soupape
égoutter la tuyauterie.
1. Visser Nº.1au fond de la
tuyauterie existante en utilisant le
ruban en Téflon ou le composé pour
les tuyaux aux filets. Nº.2devoir être
vers la face.
3. Brancher Nº.6à Nº.7, utiliser le
ruban en Téflon à l’extrémité de
Nº.6 avec les filets.
2. Visser Nº.3 dans l’ouverture de
Nº.4, utiliser le ruban en Téflon
(N’utilser pas “Loctite “ aux filets,
car peut- être il falloir remplacer
Nº.3à une date plus tard.)
1
2La vue près de
l’ installation de
no.10
8”
La tuyaterie existant
fournir par les autres
3
4
13
11
10
12
6
10
4. Attacher Nº.10 au mur (un
emplacementconvenable) avec
Nº.12 et Nº.13, ou par un autre
moyen approprié. T & S Brass
founir Nº.11
6
5. Recommencer l’eau et vérifier s’il
y a des fuites.
7
Noter: T & S Brass vous conseiller
d’installer les supports du mur B-0110
fournir avec ce modèle.

7
Allgemeine
Anleitungen
Installation:
Hinweis: Bevor Installation des
Ventils die Zufuhrleitungen
ausspülen.
1. Schrauben Sie Nr.1am Unterteil
des bereits vorhandenen Zufuhrrohres,
mit Hilfe von Teflonband oder
Rohrkitt am Gewinde, an. Nr.2sollte
zur Vorderseite zeigen.
3. Verbinden Sie Nr.6zu Nr.7mit
Hilfe von Teflonband am
Gewindeende der Nr.6.
2. Schrauben Sie Nr.3in die Öffnung
von Nr.4unter Zuhilfenahme von
Teflonband (BenutzenSie kein
Loctite, oder ähnliches, am
Gewinde, da Nr.3zu einem späteren
Zeitpunkt eventuell ausgewechselt
werden muß).
1
2Nahansicht der
Installation von
Nr.10
8”
Bereits vorhandene
Rohre sind nicht in
der Lieferung
enthalten
3
4
13
11
10
12
6
10
4. Befestigen Sie Nr.10
zur Wand (an einer günstig
gelegenen Stelle) mit Hilfe von
Nr.12 und Nr.13, oder anderen
geeigneten Materialien. Nr.11 wird
von T&S Brass mitgeliefert.
6
5. Wasserzufuhr andrehen, und auf
Dichtheitprüfen.
7
Hinweis: T&S Brass empfiehlt
dieses Modell mit den
mitgeliefertenWandhaltern
B-0110zu installieren.

T&S BRASS AND BRONZE WORKS, INC.
A firm commitment to application-engineered plumbing products
2 Saddleback Cove, P.O. Box 1088, T & S Brass-Europe
Travelers Rest, SC 29690 ‘De Veenhoeve’
Phone: [phone] Oude Nieuwveenseweg 84
Fax: [phone] CW Nieuwveen
E-mail: [email protected] The Netherlands
RELATED T&S BRASS PRODUCT LINE
MV-0770-02CW
Steam and Water Washdown Station
8