Task Force Tips TRANSFORMER Quick guide

©Copyright Task Force Tips, Inc. 2013-2014 LIS-011 December 15, 2014 Rev02
MANUAL: TRANSFORMER
Nozzle system
Nozzle system
INSTRUCTIONS FOR SAFE OPERATION AND MAINTENANCE
WARNING Understand manual before use. Operation of this device without understanding the manual and
receiving proper training is a misuse of this equipment. Obtain safety information at www.tft.
com/serial-number
WARNING This equipment is intended for use by trained personnel for firefighting. Their use for other
purposes may involve hazards not addressed by this manual. Seek appropriate guidance and
training to reduce risk of injury.
This instruction manual is intended to familiarize firefighters and maintenance personnel with the operation, servicing and safety
procedures associated with the Transformer Nozzle System.
This manual should be kept available to all operating and maintenance personnel.
TASK FORCE TIPS, INC.
MADE IN USA • www.tft.com 3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219-462-6161 • Fax [phone]
Nominal Rated Flow
150 GPM @ 100 PSI
(570 l/min @ 7 bar)
Maximum Operating Pressure
300 psi (20 bar)
DANGER
PERSONAL RESPONSIBILITY CODE
The member companies of FEMSA that provide emergency response
equipment and services want responders to know and understand the
following:
1. Firefighting and Emergency Response are inherently dangerous activities
requiring proper training in their hazards and the use of extreme caution
at all times.
2. It is your responsibility to read and understand any user’s instructions,
including purpose and limitations, provided with any piece of equipment
you may be called upon to use.
3. It is your responsibility to know that you have been properly trained in
Firefighting and /or Emergency Response and in the use, precautions, and
care of any equipment you may be called upon to use.
4. It is your responsibility to be in proper physical condition and to maintain
the personal skill level required to operate any equipment you may be
called upon to use.
5. It is your responsibility to know that your equipment is in operable
condition and has been maintained in accordance with the manufacturer’s
instructions.
6. Failure to follow these guidelines may result in death, burns or other
severe injury.
FEMSA
Fire and Emergency Manufacturers and Service Association
P.O. Box 147, Lynnfield, MA 01940 • www.FEMSA.org

©Copyright Task Force Tips, Inc. 2013-2014 LIS-011 December 15, 2014 Rev02
2
1.0 MEANING OF SAFETY SIGNAL WORDS
Asafety related message is identified by a safety alert symbol and a signal word to indicate the level of risk involved with a particular
hazard. Per ANSI standard Z535.6-2011, the definitions of the four signal words are as follows:
DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury.
NOTICE NOTICE is used to address practices not related to physical injury.
2.0 GENERAL INFORMATION
The Task Force Tips Transformer Nozzle System is designed to deliver water or foam solutions to areas inaccessible to the fire
fighter. It is primarily constructed of hard coated extruded aluminum and features a hardened stainless steel point for driving through
concrete block, mobile homes, drywall, hay bales, or other barriers. If necessary, the striking head may be struck with a hammer or
flat head axe to drive it through a barrier. A series of jets near the tip apply a wide reaching pattern. Aswivel coupling with 1.5” NH
(38mm) female hose thread is standard (National Hose Threads per NFPA #1963).
Each Transformer Nozzle System comes equipped with a unique rotary shutoff valve. The rotary shutoff valve allows the user
to operate the Transformer Nozzle System Package without an additional shutoff valve. Operation of the rotary shutoff valve is
simple. From the OFF position, a quarter turn to the left fully opens the waterway. To stop water flow from the ON position, turn
the rotary shutoff valve a quarter turn to the right. Do not operate the Transformer Nozzle System with the rotary shutoff valve in
the intermediate position between ON and OFF. If not in the ON or OFF position, the rotary shutoff valve may change position
unexpectedly.
The Transformer Nozzle System uses a separate striking head. Install the striking head in one of the three threaded holes on the
junction block.
Hand tighten the striking head assembly into the chosen port. Turn the striking cap, by hand, beyond the initial contact with the
junction block to load the junction block spring. The spring loaded striking cap stays secure in the junction block and protects the
threads from damage.
Due to the modular construction of the Transformer Nozzle System, the user may configure the nozzle in different arrangements to
suit the situation. Additional components are available from the manufacturer to further customize the Transformer Nozzle System.
The Task Force Tips Distributor Nozzle distributes water droplets over a large area.Three spinners create an interference pattern of
water droplets for a dense water pattern. The distributor nozzle attaches to the Transformer Nozzle System and provides additional
flexibility to the operator. Distributor nozzles couple to fire hose via an adapter with a 1.5” NH (37 mm) female full time swivel inlet
(National Hose Threads per NFPA #1963). When operated, a distributor nozzle provides a nominal water flow of 150 GPM at 100
PSI (560 l/min at 7 bar). The distributor nozzle’s primary construction consists of aluminum and stainless steel.
1.0 MEANING OF SAFETY SIGNAL WORDS
2.0 GENERAL INFORMATION
3.0 SAFETY
4.0 USE WITH SALT WATER
5.0 FOAM USAGE
6.0 FIREGROUND USE
7.0 WARRANTY
8.0 EXPLODED VIEW AND PARTS LIST
9.0 INSPECTION AND MAINTENANCE
TABLE OF CONTENTS

©Copyright Task Force Tips, Inc. 2013-2014 LIS-011 December 15, 2014 Rev02
3
2.0 GENERAL INFORMATION (continued)
Hammer Configuration
Striking Head
Straight Configuration
Rotary Valve
3 Port
Junction Block Extension Tube Flow Tube
Piercing Point
Coupling
Striking Head
Extension Tube
Handle Grip Configuration
Pistol Grip
Distributor Nozzle Configuration
Figure 2.0 Part Identification
DANGER An inadequate supply of nozzle pressure and/or flow will cause an ineffective stream and can
resultin injury,death orloss of property.Therecommendedflow and pressureforthe Transformer
Nozzle System is 150 gpm at 100 psi. Call 800-348- 2686 for assistance.
WARNING Do not attempt to assemble, disassemble, or configure the Transformer Nozzle System with
a pressurized fire hose attached. Safely depressurize and remove the fire hose prior to any
assembly or disassembly of the Transformer Nozzle System.
WARNING Misaligned,loose,ordamaged threads may cause thethreadedjointsto uncoupleunderpressure
resulting in injury. Nozzle joints must be properly connected. Ensure the threaded joints between
components are completely installed and hand tightened.
WARNING The piercing point has sharp edges that can cause injury by impalement. Use care when
handling and striking the Transformer Nozzle. Do not use the Transformer as a pry bar under any
circumstance. Avoid laying the tool down or storing in a position that presents an impalement
or fall hazard.
WARNING Striking the Transformer Nozzle System with a sledge or ax creates risk of injury from missed
blows.Alwayswearprotectivefiregear,eye protection, and gloves.Avoidholding the Transformer
Nozzle System in areas likely to be struck by a missed blow. Avoid standing in the path of a
swinging tool head. Avoid striking the Transformer Nozzle System when fatigued beyond one’s
ability to safely control a swing. Exercise sound judgement when operating on sloped, elevated,
or slippery surfaces.
CAUTION The Transformer Nozzle System is designed only to hit on the striking head. Striking in any other
location is considered abuse and resulting damage is not covered under warranty.
NOTICE ONLY HAND TIGHTEN THE TRANSFORMER Nozzle System THREADED JOINT. DO NOT USE A
WRENCH TO ASSEMBLE THE TRANSFORMER NOZZLE SYSTEM.
NOTICE Use of the Transformer Nozzle System as a lever or a wedge may cause the unit to bend or
fracture. Such damage is considered abuse. The resulting damage is not covered under warranty.
NOTICE Do not use the distributor nozzle to penetrate obstacles. Always create access points with
appropriate tools.

©Copyright Task Force Tips, Inc. 2013-2014 LIS-011 December 15, 2014 Rev02
4
3.0 SAFETY
WARNING Water is a conductor of electricity. Application of water and/or foam solutions on energized
electrical equipment can cause injury or death by electrocution. The amount of current that may
be carried back to the nozzle will depend on the following factors:
• Voltage of the line or equipment
• Distance from the nozzle to the line or equipment
• Size of the stream
• Whether the stream is solid or broken
• Purity of the water
The Fire Fighter and Electrical Equipment, The University of Michigan Extension Service, Fourth Printing 1983. Page 47.
WARNING Risk of electrocution! Penetrating a wall or barrier may place the Nozzle System in direct
metal to metal contact with electric wiring and equipment which can cause injury or death by
electrocution. The nozzle and water are both conductors of electricity. Assume that all wires are
energized at lethal levels. Always disable electric service prior to penetrating hidden spaces.
WARNING If nozzle gets out of control or away from operator, retreat from nozzle immediately. Do not
attempt to regain control of nozzle while flowing water. Injury from whipping can occur.
WARNING Walking on weakened roofs, floors, and decks increases risk of falling thru the structure to
areas below which may be engulfed by flame. Exercise sound judgement when operating on
questionable surfaces.
WARNING Large amounts or pieces of debris can reduce the flow of the nozzle resulting in an ineffective
flow. In the event of a blockage, it may be necessary to retreat to a safe area, uncouple nozzle
and remove debris.
CAUTION Water streams are capable of injury and damage. Do not direct water stream to cause injury or
damage to persons or property.
CAUTION Nozzle reaction will vary as supply conditions change: such as opening or closing other nozzles,
hoseline kinks, changes in pump settings, etc. The nozzle operator must always be prepared in
the event of those changes. Failure to restrain nozzle reaction can cause firefighter injury from
loss of footing and/or stream protection.
CAUTION Kinks in hose line may reduce water flow and cause injury or death to persons dependent on
water flow. Avoid tight bends to minimize risk of hoseline kinks.
CAUTION Quick changes in valve position can cause high pressure spikes due to water hammer and may
result in damaged equipment which could lead to injury or death. Open and close the valve
slowly to avoid water hammer.
4.0 USE WITH SALT WATER
Use with salt water is permissible provided nozzle is thoroughly cleaned with fresh water after each use. The service life of the nozzle
may be shortened due to the effects of corrosion and is not covered under warranty.
5.0 FOAM USAGE
The Task Force Tips Transformer Nozzle System is suitable for use with ClassA foam, especially when hidden hot spots need to be
soaked. Generally, the reach with foam is approximately 10 % less than with water only. Actual results will vary based on brand of
foam, hardness of water, temperature, etc.Always flush the nozzle thoroughly with water after foam use.
Assure that:
• Application rate is sufficient (see NFPA11 or foam manufacturer’s recommendations).
• Enough concentrate is on hand to complete task (see NFPAfor minimum duration time requirements).
• Foam logistics have been carefully planned. Allow for such things as:
• Storage of foam in a location not exposed to the hazard it protects.
• Personnel, equipment and technique to deliver foam at a rapid enough rate.
• Removal of empty foam containers.
• Keeping clear path to deliver foam as hoses, other equipment and vehicles are deployed.
WARNING Improper use of foam can result in injury or damage to the environment. Follow foam
manufacturer’s instructions and fire service training to avoid:
• Using wrong type of foam on a fire, i.e. Class A foam on a Class B fire.
• Plunging foam into pools of burning liquid fuels.
• Causing environmental damage.
• Directing stream at personnel.
WARNING There is a wide variety of foam concentrates. Each user is responsible for verifying that any
foam concentrate chosen to be used with this unit has been tested to assure that the foam
obtained is suitable for the purpose intended.

©Copyright Task Force Tips, Inc. 2013-2014 LIS-011 December 15, 2014 Rev02
5
6.0 FIREGROUND USE
ITISTHE RESPONSIBILITYOF THEINDIVIDUALFIRE DEPARTMENTORAGENCYTODETERMINE PHYSICALCAPABILITIES
AND SUITABILITY FOR AN INDIVIDUAL’S USE OF THIS EQUIPMENT.
NOTICE Many factors contribute to the extinguishment of a fire. Among the most important is delivering water
at a flow rate sufficient to absorb heat faster than is being generated. The flow rate depends largely on
the pump discharge pressure and hose friction loss.
Friction loss can be calculated using a hydraulic equation such as:
PDP = NP+FL+DL+EL
PDP = Pump discharge pressure in PSI
NP = Nozzle pressure in PSI
FL = Hose friction loss in PSI
DL = Device loss in PSI
EL = Elevation loss in PSI
The Transformer Nozzle System’s estimated device loss is between 30 and 40 PSI (2 to 3 Bar) for most configurations. For additional
information on calculating specific hose layouts, consult an appropriate fire-service training manual, A Firefighters Guide to Nozzles
published by Task Force Tips, or call TFT’s “Hydraulics Hotline” at 800-348-2686, request document #LTT-010.
7.0 WARRANTY
Task Force Tips, Inc., 3701 Innovation Way, Valparaiso, IN 46383-9327 USA (“TFT”) warrants to the original purchaser of its Nozzle
System (“equipment”), and to anyone to whom it is transferred, that the equipment shall be free from defects in material and
workmanship during the five (5) year period from the date of purchase.
TFT’s obligation under this warranty is specifically limited to replacing or repairing the equipment (or its parts) which are shown by
TFT’s examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the claimant must return the
equipment to TFT, at 3701 Innovation Way, Valparaiso, IN 46383-9327 USA, within a reasonable time after discovery of the defect.
TFT will examine the equipment. If TFT determines that there is a defect attributable to it, TFT will correct the problem within a
reasonable time. If the equipment is covered by this limited warranty, TFT will assume the expenses of repair.
If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to
refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited
warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.
This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who is
an intended or unintended beneficiary of the equipment, shall not be entitled to recover from TFT any consequential or incidental
damages for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT. It is agreed
and understood that the price stated for the equipment is in part consideration for limiting TFT’s liability. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including failure to
provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone
else.
THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT ALL
IMPLIEDWARRANTIESOFMERCHANTABILITYANDALLIMPLIEDWARRANTIESOF FITNESSFORAPARTICULARPURPOSE.
THERE IS NO WARRANTY OFANY NATURE MADE BY TFT BEYOND THAT STATED IN THIS DOCUMENT.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

©Copyright Task Force Tips, Inc. 2013-2014 LIS-011 December 15, 2014 Rev02
6
8.0 EXPLODED VIEW AND PARTS LIST
TRANSFORMER
Piercing Nozzle
PA206
www.tft.com
ON ON
PA22 6
ON ON
PA22 7
OFF OFF OFF OFF
PA22 8
OFFON
www.tft.com219-462-6161
OFFON
8
17
18
19
22
36
1235
4672
210 2
9
8
9
8
32
30
29
2
28
27 26
25
23
24
23
2
31
33
34
35
21
20
17
18 19
22
14
13
12
11
40
41
39
38
2
40
41
31
30
39
38
2
37
32
34
35
16
2
15
28
TASK FORCE TIPS®
FIRE FIGHTING EQUIPMENT
®
[phone]
www.tft.com
M
A
X
O
P
E
R
A
T
I
N
G
P
R
E
S
S
U
R
E
T
R
A
N
S
F
O
R
M
E
R
PIERCING NOZZLE
P
A
2
0
5
3
0
0
P
S
I
(
2
0
b
a
r
/
2
0
0
0
k
P
a
)

©Copyright Task Force Tips, Inc. 2013-2014 LIS-011 December 15, 2014 Rev02
7
PARTS LIST
INDEX DESCRIPTION QTY. PART
1 PIERCING NOZZLE STRIKING CAP 1 PA161
2 O-RING-125 9 VO-125
3 O-RING-012 1 VO-012
4 PIERCING NOZZLE STRIKING PLUG 1 PA162
5 BELLEVILLE WASHER 2 VM4903
6 7/16-14 NYLOCK HEX NUT 1 VT43-14LNT
7 3 PORTJUNCTION BLOCK 1 PA150
8 LABEL: BRAND 3 PA206
919" EXTENSION TUBE 2 PA110 40" EXTENSION TUBE 1 PA170
12" EXTENSION TUBE 1 PA230
10 GRIP MOUNT 1 PA250
11 GRIP SPACER 1 HM693-F
12 PISTOLGRIP - BLACK 1 HM692-BLK
13 WASHER 1 VM4901
14 3/8-16 X 1 SOCKET HEAD SCREW 1 VT37-16SH1.0
15 FLOW PATTERN EXTENSION SECTION 1 PA120
16 PIERCING POINT 1 PA141
17 NAME LABEL: TRANSFORMER PIERCING NOZZLE 2 PA205
18 LABEL: ROTARY VALVE OFF - RED 1 PA227
19 LABEL: ROTARY VALVE ON - BLUE 1 PA226
20 FOLLOWER 2 U251
21 3/8-24 X 3/8 DOG POINT 2 H515
22 LABEL: ROTARY VALVE - BLUE 1 PA228
23 O-RING-130 2 VO-130
24 VALVE BODY 1 PA221
25 CAP 1 PA224
26 O-RING-135 1 VO-135
27 SEAT 1 PA223
28 VALVE 1 PA222
29 INLETADAPTER 1 PA225
30 3/16" SS BALL(34) PER RACE 68 V2120
31 PORT PLUG 2 B770
32 O-RING-134 2 VO-134
33 GASKET GRABBER 1 G606
34 COUPLING 1.5" 2 G690*
35 GASKET - 1.5" HOSE COUPLING 2 V3130
36 STORAGE BAG 1 PA200
37 MATE 1 PA264
38 NOZZLE BASE 1 PA261
39 HEX PORT PLUG 1 PA265
40 NOGGIN 3 PA262
41 SPINNER 3 PA263
* - CONSULT FACTORYFOR SPECIAL THREADS

©Copyright Task Force Tips, Inc. 2013-2014 LIS-011 December 15, 2014 Rev02
TASK FORCE TIPS, INC.
MADE IN USA • www.tft.com 3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219-462-6161 • Fax [phone]
9.0 INSPECTION AND MAINTENANCE
The Task Force Tips Transformer Nozzle System is designed and manufactured to be damage resistant and require minimal
maintenance. However, as the primary firefighting tool upon which your life depends, it should be treated accordingly.
Nozzle must be inspected before each use for proper operation and function according to this checklist:
• None of the nozzle jets are clogged
• There is no obvious damage such as missing, broken or loose parts, etc
• The threaded joints between component are hand tight and leak free
• The coupling is tight and leak free
• Valve opens and closes freely
WARNING Before each use nozzle must be inspected for proper operation and function according to
inspection criteria above. Any nozzle that fails inspection is dangerous to use and must be
repaired before using. Operating a nozzle that fails any part of the inspection is a misuse of this
equipment.
WARNING Performance tests shall be conducted on the special purpose nozzle after a repair, or anytime
a problem is reported to verify operation in accordance with Task Force Tips test procedures.
Consult factory for the procedure that corresponds to the model of the nozzle. Any equipment
which fails the related test criteria should be removed from service immediately. Equipment can
be returned to the factory for service and testing.
CAUTION Any alterations to the equipment constitutes a misuse of this product and could diminish safety.
CAUTION Maximum operating pressure 300 psi (20 bar). Do not exceed 300 psi (20 bar) on either side of the
valve.
CAUTION Transformer Nozzle System must be properly connected. Mismatched or damaged connectors
may cause leaking or uncoupling under pressure and may cause injury.
CAUTION Dissimilar metals coupled together can cause galvanic corrosion that can result in the inability
to unscrew the threads or complete loss of thread engagement over time. Per NFPA 1962 (2013
Edition), if dissimilar metals are left coupled together an anti-corrosive lubricant should be applied
to the threads. Also the couplings should be disconnected and inspected at least quarterly.