Task Force Tips PROTECTOR Quick guide

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
MANUAL: PROTECTOR
STATION MONITOR
INSTRUCTIONS FOR SAFE OPERATION AND MAINTENANCE
WARNING Understand manual before use. Operation of this device without understanding the manual and
receiving proper training is a misuse of this equipment. Obtain safety information at www.tft com/
serial-number
This instruction manual is intended to familiarize fi refi ghters and maintenance personnel with the operation, servicing, and safety
procedures associated with the PROTECTOR Station Monitor. This manual should be kept available to all operating and maintenance
personnel.
TASK FORCE TIPS, INC.
MADE IN USA • www.tft.com 3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219-462-6161 • Fax [phone]
Maximum fl ow is
1250 GPM (4800 L/MIN)
Maximum inlet pressure is
250 PSI (17 BAR)
Shown with optional valve.

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
2
DANGER
PERSONAL RESPONSIBILITY CODE
The member companies of FEMSA that provide emergency response
equipment and services want responders to know and understand the
following:
1. Firefi ghting and Emergency Response are inherently dangerous activities
requiring proper training in their hazards and the use of extreme caution
at all times.
2. It is your responsibility to read and understand any user’s instructions,
including purpose and limitations, provided with any piece of equipment
you may be called upon to use.
3. It is your responsibility to know that you have been properly trained in
Firefi ghting and /or Emergency Response and in the use, precautions, and
care of any equipment you may be called upon to use.
4. It is your responsibility to be in proper physical condition and to maintain
the personal skill level required to operate any equipment you may be
called upon to use.
5. It is your responsibility to know that your equipment is in operable
condition and has been maintained in accordance with the manufacturer’s
instructions.
6. Failure to follow these guidelines may result in death, burns or other
severe injury.
FEMSA
Fire and Emergency Manufacturers and Service Association
P.O. Box 147, Lynnfi eld, MA 01940 • www.FEMSA.org

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
3
1.0 MEANING OF SAFETY SIGNALWORDS.............................................................................................................4
2.0 SAFETY ..............................................................................................................................................................4
3.0 GENERALINFORMATION....................................................................................................................................5
3.1 VARIOUS MODELS AND TERMS
3.2 MECHANICALSPECIFICATIONS
3.3 USE WITH SALT WATER
3.4 INLET FLANGE OPTIONS
3.5 OUTLET OPTIONS
3.6 OVERALLDIMENSIONS
4.0 INSTALLATION......................................................................................................................................................8
4.1 STRUCTURALREQUIREMENTS
4.2 NOZZLE INSTALLATION
4.3 PRESSURE GAGE
4.4 HANDLE INSTALLATION
4.5 DRAINING RESIDUALWATER
5.0 OPERATION ..........................................................................................................................................................9
5.1 VALVE OPERATION
5.2 HORIZONTALROTATION CONTROL
5.3 ELEVATION CONTROL
6.0 FLOW CHARACTERISTICS................................................................................................................................10
6.1 AUTOMATIC NOZZLES
6.2 STACKED TIPS FLOWAND REACH
6.3 STREAM STRAIGHTENERS
6.3.1 STREAM STRAIGHTENERS WITH STACKED TIPS
6.3.2 STREAM STRAIGHTENERS WITH FOG NOZZLES
6.4 MONITOR FRICTION LOSS
7.0 DRAWINGSAND PART LISTS............................................................................................................................16
8.0 WARRANTY.........................................................................................................................................................18
9.0 MAINTENANCE...................................................................................................................................................19
9.1 LOWER SEALAND VALVE SEAT
9.2 UPPER SWIVELSEALAND SWIVEL INSERTS
10.0 ANSWERS TO YOUR QUESTIONS....................................................................................................................19
11.0 INSPECTION CHECKLIST...................................................................................................................Back Cover
Table Of Contents

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
4
1.0 MEANING OF SAFETY SIGNAL WORDS
A safety related message is identifi ed by a safety alert symbol and a signal word to indicate the level of risk involved with a particular
hazard. Per ANSI standard Z535.6-2011, the defi nitions of the four signal words are as follows:
DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor
or moderate injury.
NOTICE NOTICE is used to address practices not related to physical injury.
2.0 SAFETY
The operation of this monitor can be dangerous. The following must be observed at all times.
DANGER An inadequate supply of nozzle pressure and/or fl ow will cause an ineff ective stream and can
result in injury, death, or loss of property. See fl ow graphs or call 800-348-2686 for assistance.
WARNING Injury or death may occur by attempting to use a damaged monitor. Before using the monitor
inspect it for damage resulting from:
• Failure to drain monitor followed by exposure to freezing conditions
• Exposure of monitor to temperatures in excess of 160 degrees F
• Structural damage caused by over-pressurization
• Missing parts, physical abuse, exposure to severe chemicals
• Deformed or cracked fl anges damaged as a result of improper installation
- Excessive bolt torque
- Wrong tightening sequence
WARNING Injury can result from an inadequately supported monitor. The monitor mount must be capable of
supporting 1050 lbs (475 kg) of nozzle reaction force.
WARNING The stream exiting a monitor is very powerful and capable of causing injury and property damage.
Make sure the monitor is securely attached to the base and pointing in a safe direction before
water to the monitor is turned on. Use care in directing the stream.
WARNING The monitor may be damaged if frozen while containing suffi cient amounts of water. Such damage
may be diffi cult to detect visually and can lead to possible injury or death. Any time the monitor is
subject to possible damage from freezing, it must be hydrostatically tested by qualifi ed personnel
before being considered safe for use.
WARNING This equipment is intended for use by trained personnel for fi refi ghting. Their use for other
purposes may involve hazards not addressed by this manual. Seek appropriate guidance and
training to reduce risk of injury.
CAUTION Maximum fl ow and pressure is 1250 gpm (4800 l/min) and 250 psi (17 bar). Damage or injury may
result if the monitor is operated beyond these limits.
CAUTION On many vehicle installations, the monitor is the highest point on the apparatus. Be sure there
is suffi cient clearance to safely pass under any doors or overhead obstructions. Always check
parked position of the monitor before moving.
NOTICE To prevent mechanical damage, do not drop or throw equipment.

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
5
3.0 GENERAL INFORMATION
The Task Force Tips Protector is a simple and rugged fi xed station monitor with many unique features. Its patented waterway gives
low friction loss and delivers water to the nozzle with fewer twists and turns than a conventional monitor. The optional built-in on/
off valve with position indicator eliminates the need to add a costly valve to the monitor installation. The Protector is capable of
fl owing up to 1250 gpm (4800 l/min) while maintaining a FULL 360° rotational ability. The lever-action rotational lock is activated in
one motion, visually confi rmed, and securely holds the monitor’s horizontal position. The Protector can be directly bolted to many
common pipe fl anges. The outlet is available with various 2.5” (65mm) male threads. The simple and basic design requires no grease
application or other maintenance. Swiveling elements and seals (including valve seat) can be replaced within a few minutes with
common hand tools. All models are equipped with an automatic drain valve to fully evacuate the monitor and optional on/off valve
after each use. A threaded pipe port (1/4” NPT) (6mm) is provided for pressure gauge installation. Maximum pressure is 250 psi
(17 bar). The Protector is hard anodized ANSI 356-T6 aluminum and is fully powder coat fi nished inside and out. Swivel clamps, 3”
(75mm) valve ball, trunnions, and hardware are 18-8 stainless steel.
3.1 VARIOUS MODELS AND TERMS
The Protector monitor is available in several diff erent models and inlet connections. The two body styles are shown in fi gures 3.1A
and 3.1B below.
Fig 3.1A
Protector with Shutoff Valve,
Threaded Exit and 4” ANSI 150 inlet
Fig 3.1B
Protector without Valve,
Threaded Exit and 4” ANSI 150 inlet
Figure 3.1C identifi es terms that describe the various parts and controls of the monitor.
Serial Number
Flanged Base
Direction Control Handle
Elevation Locking Knob
Automatic Drain Valve
(See Section 4.5)
Horizontal Rotation Locking Lever
Port for Pressure Gauge 1/4" NPT
Valve Handle
Valve Position Indicator
Elevation Swivel
Threaded
Exit
Horizontal Swivel
Fig 3.1C
Protector Parts Identifi cation

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
6
3.2 MECHANICAL SPECIFICATIONS
US METRIC
Maximum weight with optional shutoff valve 35.2 lb 15.7 kg
Maximum weight without valve 27.8 lb 12.5 kg
Min. Flow Area 3” Valve Ball 6.95 square inches 44.8 square cm
Min. Flow Area 2.5” Male Threaded Outlet 4.36 square inches 28.1 square cm
Max Flow 1250 gpm 4800 l/min
Max Operating Pressure 250 psi 17 bar
Materials Used 356-T6 aluminum, 6000-series aluminum,
18-8 stainless steel, UHMW-PE, nylon,
acrylonitrile rubber, Dupont Alcryn 2080BK
0 10002000300040005000
0
2
4
6
8
10
12
14
16
18
20
0
25
50
75
100
125
150
175
200
225
250
275
300
0 250 500 750 1000 1250 1500
Flow Rate (l/min)
Monitor Inlet Pressure (bar)
Monitor Inlet Pressure (psi)
Flow Rate (gpm)
Protector Safe Operating Envelope
Nozzle B
Nozzle D
Nozzle A Nozzle C
Do not exceed
Maximum Monitor Inlet Pressure
Do not exceed
Max. Monitor
Flow Rate
Nozzle A fl ows 500 gpm at 100 psi (1900 l/min at 7 bar), K factor = 50
Nozzle B fl ows 750 gpm at 100 psi (2800 l/min at 7 bar), K factor = 75
Nozzle C fl ows 1000 gpm at 100 psi (3800 l/min at 7 bar), K factor = 100
Nozzle D fl ows 1250 gpm at 100 psi (4800 l/min at 7 bar), K factor = 125
Fig. 3.2
Protector Safe Operating Envelope
3.3 USE WITH SALT WATER
Use with salt water is permissible provided the monitor is thoroughly cleaned with fresh water after each use. The service life of the
monitor may be shortened due to the eff ects of corrosion and is not covered under warranty.

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
7
3.4 INLET FLANGE OPTIONS
Four diff erent fl ange options are available. Monitor height varies depending on whether the fl ange inner diameter is 4” (100 mm)
or 3” (80 mm), as shown in fi gure 3.4 below. Monitor height is measured from the bottom of the inlet fl ange to the centerline of the
elevation swivel.
Inlet Flange option 3” ANSI 125/150
(also DN80 PN20) DN80 P16 4” ANSI 150 ( also DN100 PN20) DN100 PN16
Monitor height
(inlet to elevation swivel) 16.2 in (41.1 cm) 16.2 in (41.1 cm) 19.1 in (48.5 cm) 19.1 in (48.5 cm)
Height at +30° elevation 24.7 in (62.7 cm) 24.7 in (62.7 cm) 27.6 in (70.1 cm) 27.6 in (70.1 cm)
Max. height at +80° elevation 31.0 in (78.7 cm) 31.0 in (78.7 cm) 33.9 in (86.1 cm) 33.9 in (86.1 cm)
Fig 3.4
Monitor height with each inlet fl ange option
3.5 OUTLET OPTIONS
Three options are available for the 2.5 inch male threaded outlet:
• National Hose Thread (NH, also referred to as National Standard Thread)
• National Pipe Straight Hose (NPSH, also referred to as Iron Pipe Thread)
• British Standard Pipe Thread (BSP)
3.6 OVERALL DIMENSIONS
11.3"
[288mm]
16.1"
[408mm] 19.1"
[485mm]
80°
27.7"
[703mm]
70°
Maximum flow is 1250 GPM
(4800 L/MIN)
Maximum inlet pressure is
250 PSI (17 BAR)
Fig 3.6
Overall Dimensions

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
8
4.0 INSTALLATION
The Protector station monitor is installed to a riser pipe by a bolted fl ange joint. Verify that no interference exists between the
Protector and surrounding hardware that would limit its usefulness. If a valve is to be mounted under the Protector, verify that no
interference exists with the valve handle. If a butterfl y valve is to be mounted under the Protector, verify that no interference exists
between the butterfl y and the fl anged base of the Protector when the valve is in its open position.
4.1 STRUCTURAL REQUIREMENTS
The structure that the Protector station monitor is mounted to must withstand the internal pressure of the monitor as well as shear
and bending forces due to nozzle reaction. Nozzle reaction can be as high as 1050 lbs (480 kg) (1250 gpm at 250 psi).
For fl anged connections the use of fl at fl anges without raised faces is recommended. Use a ring gasket as defi ned in ASME 16.21 or
ISO 7483. Tighten fl ange bolts in an alternating sequence as shown in fi gure 4.1A. Tighten sequentially each bolt or stud three times
with 30%, then 60%, and fi nally 100% of the specifi ed torque in fi gure 4.1B.
T
ighten Sequentially Each Bolt Three Times.
1
5
3
726
4
8
1
3
2
4
Fig 4.1A
Flange Bolt Tightening Sequence
FLANGE TYPE OUTSIDE
DIAMETER
THICKNESS BOLT HOLE
CIRCLE
# OF
BOLTS
SIZE OF
BOLTS
TORQUE
ON BOLTS
in mm in mm in mm in mm ft-lb N-m
3” ANSI 125/150-DN80 PN20 7.5 190 0.75 20 6.0 152.5 4 5/8 16 76-80 100-110
4” ANSI 150-DN100 PN20 9.0 230 0.94 23 7.5 190 8 5/8 16 76-80 100-110
DN80, PN16 FLANGE 7.9 200 0.87 22 6.3 160 8 5/8 16 76-80 100-110
DN100, PN16 FLANGE 8.7 220 0.87 22 7.1 180 8 5/8 16 76-80 100-110
Fig 4.1B
Flange Specifi cations
WARNING Injury can result from an inadequately supported monitor. The monitor mount must be capable
of supporting the nozzle reaction force which can be as high as 1050 lbs (480 kg). Flanges and
pipe made from plastic are inadequate for monitor mounting and must not be used. This monitor
is not recommended for portable use.
4.2 NOZZLE INSTALLATION
The nozzle is simply screwed onto the monitor’s exit threads until it bottoms out and compresses the rubber gasket.
CAUTION The nozzle threads must match the threads of the Protector monitor in both size and type.
Mismatched or damaged threads may cause the nozzle to leak or uncouple under pressure and
could cause injury.
CAUTION Do not connect aluminum to brass or brass to aluminum. Dissimilar metals coupled together
can cause galvanic corrosion that will freeze the threaded joint or cause complete loss of
thread engagement. If dissimilar metals must be coupled together, the eff ects of corrosion can
be greatly delayed by various coatings on the metal such as powder paint, hard anodizing, or
silicone grease.

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
9
4.3 PRESSURE GAGE
There is a ¼” NPT female threaded hole adjacent to the elevation swivel, as shown in Figure 4.3. The hole is plugged from the
factory. If a pressure gage is desired, unscrew the plug and install the gage using pipe sealant. Make sure the gage does not interfere
with operation.
Pressure Gage Port 1/4" NP
T
Handle Mounting Screw
Fig 4.3
Pressure Gage Port and Handle Mounting Screw
4.4 HANDLE INSTALLATION
The tiller handle is shipped loose from the monitor and must be installed to complete the installation process. When installing the
tiller handle, be sure to coat the threads of the mounting screw with the Loctite supplied in the hardware packet. Handle mounting
screw location is shown in Figure 4.3.
4.5 DRAINING RESIDUAL WATER
NOTICE All monitors, valves and standpipes exposed to freezing conditions must be drained immediately
following use to prevent damage. To drain a standpipe, a drainage port must be opened
underground below the frost depth to keep water out of the standpipe until the next use.
All Protector station monitors are equipped with an automatic drain valve attached to a port located just above the valve seat and/
or lower seal. The automatic drain valve ensures the monitor is completely drained following use, which minimizes susceptibility
to damage from corrosion and freezing water. The drain valve seal membrane is designed to close automatically when pressure
exceeds 5 psi. When pressure drops below 5 psi, the seal membrane will open to allow drainage. If the automatic drain valve is
omitted or disabled, then the monitor must be manually drained after use to prevent damage.
5.0 OPERATION
5.1 VALVE OPERATION
For models equipped with a built-in valve, the fl ow is OFF when the valve handle is horizontal and ON when the handle is vertical.
Parts are manufactured so that the valve cannot be assembled out of phase. A position indicator shows the valves position as “OFF”
or “ON”. The position that the valve is normally left in will depend upon your particular location’s standard operating procedure.
Operate the valve slowly to reduce water hammer.

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
10
5.2 HORIZONTAL ROTATION CONTROL
The Protector can rotate from side to side on its swivel base. Lift the rotation lock lever and rotate the monitor right or left using the
directional control handle (see fi gure 5.2). To lock the monitor in position, depress the rotation lock lever. A small spring holds the
rotation lock lever in the unlocked position when it is disengaged. When the monitor is not in use, the rotation lock lever should be
kept in the locked position.
Apply Force Here
to Change Horizontal
Orientation
Apply Force Here
to Change Elevation
Rotation
Lock
Elevation
Lock
Fig 5.2
Rotation & Elevation Control
5.3 ELEVATION CONTROL
The up and down direction (elevation) of the stream is changed by pushing or pulling vertically on the direction control handle (see
fi gure 5.2). Twisting the elevation locking knob clockwise will increase the drag on the upper swivel joint to “lock” the monitor at a
particular elevation. Select discharge devices that do not exceed the 70 ft-lb locking capability of the elevation lock.
For a typical fog nozzle, the maximum allowable weight works out to be about 40 lbs (18.1 kg).
CAUTION Injury can result from the monitor changing direction due to an off center nozzle reaction. An off
center nozzle reaction may be caused by debris in the nozzle causing an asymmetrical stream.
Always keep the rotation lock tight when not rotating the monitor. Always keep one hand on the
tiller handle when loosening the locking knob.
6.0 FLOW CHARACTERISTICS
6.1 AUTOMATIC NOZZLES
Automatic nozzles maintain a constant pressure by adjusting their orifi ce to match the available fl ow. Consult the nozzle manufacturer
for maximum fl ow and pressure range. In all cases do not exceed 1250 gpm (4800 LPM) and 250 psi (17 bar).

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
11
6.2 STACKED TIPS FLOW AND REACH
INLET PRESSURE (PSI)
NOZZLE
DIAMETER
(inches)
40 60 80 100
FLOW
(GPM)
REACTION
(LBS)
FLOW
(GPM)
REACTION
(LBS)
FLOW
(GPM)
REACTION
(LBS)
FLOW
(GPM)
REACTION
(LBS)
1.375 360 120 440 180 500 240 560 300
1.50 420 140 520 210 600 280 670 350
1.75 580 190 700 290 810 380 910 480
2.00 750 250 920 380 1000 500 1190 630
INLET PRESSURE (BAR)
NOZZLE
DIAMETER
(MM)
2.8 4.1 5.5 7
FLOW
(l/min)
REACTION
(KG)
FLOW
(l/min)
REACTION
(KG)
FLOW
(l/min)
REACTION
(KG)
FLOW
(l/min)
REACTION
(KG)
35 1360 50 1670 80 1890 110 2120 140
38 1590 60 1970 100 2270 130 2540 160
45 2200 90 2650 130 3070 170 3440 220
50 2840 110 3480 170 4010 230 4500 290
Fig 6.2A
Stacked Tip Flow Table
0.0
0.2
1.2
1.0
0.8
0.6
0.4
PRESSURE (BAR)
0
20
40
60
80
100
120
140
160
180
200
0 200 400 600 800 1000 1200 1400 1600
FLOW (GPM)
PRESSURE (PSI)
0 1000 2000 3000 4000 5000 6000
(LPM)
1 3/8" TIP
1 1/2" TIP 2" TIP
STACK TIP PERFORMANCE
(PRESSURE IS NOZZLE EXIT PITOT PRESSURE)
1 3/4" TIP
Fig 6.2B
Stacked Tip Flow Graph

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
12
0
20
40
60
80
0.0 40.0 80.0 120.0 160.0 200.0 240.0 280.0
40 PSI
60 PSI
100 PSI
80 PSI
HORIZONTAL DISTANCE (FEET)
VERTICAL DISTANCE (FEET)
VERTICAL DISTANCE (M)
0.040.0 80.0 0.060.02 HORIZONTAL DISTANCE (M)
1.375 INCH TIP
0
10
20
0
20
40
60
80
0.0 40.0 80.0 120.0 160.0 200.0 240.0 280.0
40 PSI
60 PSI
100 PSI
80 PSI
HORIZONTAL DISTANCE (FEET)
VERTICAL DISTANCE (FEET)
VERTICAL DISTANCE (M)
0.040.0 80.0 0.060.02 HORIZONTAL DISTANCE (M)
1.50 INCH TIP
0
10
20
0
20
40
60
80
0.0 40.0 80.0 120.0 160.0 200.0 240.0 280.0
40 PSI
60 PSI
100 PSI
80 PSI
HORIZONTAL DISTANCE (FEET)
VERTICAL DISTANCE (FEET)
VERTICAL DISTANCE (M)
0.040.0 80.0 0.060.02 HORIZONTAL DISTANCE (M)
1.75 INCH TIP
0
10
20
0
20
40
60
80
0.0 40.0 80.0 120.0 160.0 200.0 240.0 280.0
40 PSI
60 PSI
100 PSI
80 PSI
HORIZONTAL DISTANCE (FEET)
VERTICAL DISTANCE (FEET)
VERTICAL DISTANCE (M)
0.040.0 80.0 0.060.02 HORIZONTAL DISTANCE (M)
2 INCH TIP
0
10
20
Fig 6.2C
Stacked Tips Stream Trajectory Graphs

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
13
0 40 80 120 160 200 240 280 320
0
20
40
60
80
100
120
140
160
VERTICAL DISTANCE (FEET)
HORIZONTAL DISTANCE (FEET)
800604020
20
40
0
HORIZONTAL DISTANCE (METERS)
VERTICAL DISTANCE (METERS)
2.0 INCH TIP, 100 PSI, 1190 GPM
60 DEGREES
30 DEGREES
45 DEGREES
75 DEGREES
Fig 6.2D
Eff ects of Elevation on Trajectory
0
10
40
20
80
040 80 120 160 200 240 280 320 360
HORIZONTAL DISTANCE (FEET)
2.00 INCH TIP, 100 PSI, 1190 GPM
VERTICAL DISTANCE (FEET)
NO WIND
20 MPH TAILWIND
20 MPH
HEADWIND
0015705520
VERTICAL DISTANCE (M)
HORIZONTAL DISTANCE (M)
Fig 6.2E
Eff ects of Wind on Reach

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
14
6.3 STREAM STRAIGHTENERS
6.3.1 STREAM STRAIGHTENERS WITH STACKED TIPS
Turbulence though the Protector station monitor is very low but stream quality and reach can be improved with the use of the integral
stream straightener on the TFT stacked tip nozzle.
OK
6.3.2 STREAM STRAIGHTENERS WITH FOG NOZZLES
When using a fog nozzle it is recommended that no stream straightener be used since the fog nozzle’s fl ow path generally serves as
a stream straightener. Use of a stream straightener with a fog nozzle will increase the stresses on the elevation locking clamp due
to the greater cantilevered weight. Select discharge devices that do not exceed the 70 ft-lb locking capability of the elevation lock.
NO

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
15
6.4 MONITOR FRICTION LOSS
0
5
10
15
20
25
30
0 200 400 600 800 1000 1200
FLOW (GPM)
FRICTION LOSS (PSI)
2.1 psi @ 350 gpm
0.1 bar @ 1300 l/min
4.4 psi @ 500 gpm
0.3 bar @ 2000 l/min
9.9 psi @ 750 gpm
0.7 bar @ 3000 l/min
27 psi @ 1250 gpm
1.8 bar @ 4500 l/min
FRICTION LOSS (BAR)
FLOW (l/min)
1
2
0
0 750 1525 2300 3030 3800 4500
Fig 6.4
Protector Station Monitor Friction Loss

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
16
7.0 DRAWING & PART LIST
56
8
5554
123456789 11
12
17
13
16
15
18
53
52
51
50
20
18
49
48
47
46
43
42
41
40
44
45
39
38 37 36 35
34
33
32
17
1831
30
29
28
27
26
25
24
23
22
21
20
18
19
11
10
14
57

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
17
PROTECTOR PARTS LIST
INDEX DESCRIPTION QTY PART #
1SLIDE 1 Z285
25/32 X 1-1/2 COTTER PIN 1 VP156X1.5
33/4-10 SLOT FIN HEX NUT 1 VT75-10SF
4FLAT SS WASHER 1 VW1.5X81-134
5VALVE HANDLE 1 Z280
6SMALLEY RING 1 V4235
7BELLEVILLE SPRING 1 VM4900
8O-RING-214 1 VO-214
9TRUNNION 1 Z265
10 AUTOMATIC DRAIN VALVE 1 A-DRAIN-KIT
11 BELL ALUMINUM 1 Z210A
12 1/4"NPT HEX HEAD PLUG 1 VFHP2M
13 1/4 X 1-3/8 HDP SPIROL 1 VP250X1.375H
14 OVERRIDE KNOB LABEL 1 Y4176
15 KNOB 1 Z245
16 LOCKING BOLT 1 Z240
17 CLAMP THREADED 2 Z221
18 SWIVEL INSERT 4 Z225
19 UPPER SWIVEL SEAL 1 Z230
20 CLAMP 2 Z220
21 5/16-18 ALL METAL FLEX-
LOCK NUT
1 VT31-18SLNT
22 1/16 X 1/2 COTTER PIN 1 VP063X.50
23 1/2-13 X 1-3/4 HEX BOLT
FULLY THREADED
1 VT50-13HX1.7
24 TRUNNION 1 Z260
25 EXIT ALUM. 2.5"BSP 1 Z310ABJ
EXIT ALUM. 2.5"NPSH Z310AIJ
EXIT ALUM. 2.5"NH Z310ANJ
26 1/2-13 X 2-3/4 HEX BOLT
FULLY THREADED
1 VT50-13HX2.7
27 O-RING-016 1 VO-016
28 ELEVATION HANDLE NUT 1 Z316
29 ELEVATION HANDLE 1 Z315
30 HANDLE GRIP 1 Z317
31 LOWER SEAL 1 Z275
32 1/2-13 X 2.5 SOCKET HEAD
SCREW
1 VT50-13SH2.5
INDEX DESCRIPTION QTY PART #
33 NAME LABEL: PROTECTOR
STATION MONITOR
1 ZL101
34 CLEVIS PIN 1/4 X 2 1 X180
35 ROTATIONAL LOCK LEVER
ALUM.
1 X160
36 ROTATION LOCK LEVER
SPRING
1 X152
37 ROTATION LOCK INSERT 1 X170
38 INDUSTRIAL BELL WITH
RIM
1 Z425
39 3"ANSI FLANGE ALUM. 1 X410-3ASA
FLANGE ALUM. 4"ANSI/XF X414-4ASA
FLANGE ALUM. DN80
PN16/XF
X423
FLANGE ALUM. DN100
PN16/XF
X424
40 CUP SEAL 1 X125
41 WEAR STRIP 1 X120
42 MODEL NUMBER LABEL 1 A1303
43 SS CLEVIS PIN RETAINER 1 X137
44 REAR VALVE SEAT 1 Z270
45 VALVE BALL 1 Z250
46 GREASE FITTING 1 VT25-28ZERK
47 3/8-24 X 3/8 SOCKET SET
SCREW
2 VT37-24SS375
48 5/16" SS BALL 76 VB.312
49 S/N LABEL: PROTECTOR/ 1 ZL102
50 1/2-13 X 1-1/4 COUPLING
NUT
1 VT50-13CPLNT
51 EXTERNAL SELF-LOCKING
RING
1 VR4290
52 WASHER 1 VW500x265-63
53 SLIDE LINK 1 Z286
54 1/4-28 X 1/2 BUTTON HEAD
SCREW
1 VT25-28BH500
55 2.5" CLAPPER WASHER 1 X752
56 PLUG 1 Z261
57 O-RING-117 1 VO-117
NOTE: SPECIFY COLOR WHEN ORDERING
AMERICAN RED OR RAL 3000

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
18
8.0 WARRANTY
Task Force Tips, Inc., 3701 Innovation Way, Valparaiso, Indiana 46383-9327 (“TFT”) warrants to the original purchaser of its Protector
Station Monitor (“equipment”), and to anyone to whom it is transferred, that the equipment shall be free from defects in material and
workmanship during the fi ve (5) year period from the date of purchase.
TFT’s obligation under this warranty is specifi cally limited to replacing or repairing the equipment (or its parts) which are shown by
TFT’s examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the claimant must return
the equipment to TFT, at 3701 Innovation Way, Valparaiso, Indiana 46383-9327, within a reasonable time after discovery of the
defect. TFT will examine the equipment. If TFT determines that there is a defect attributable to it, it will correct the problem within a
reasonable time. If the equipment is covered by this limited warranty, TFT will assume the expenses of repair.
If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to
refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited
warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.
This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who is
an intended or unintended benefi ciary of the equipment, shall not be entitled to recover from TFT any consequential or incidental
damages for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT. It is agreed
and understood that the price stated for the equipment is in part consideration for limiting TFT’s liability. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including failure to
provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone
else.
THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE.
THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THE DOCUMENT.
This limited warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state.

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
9.0 MAINTENANCE
The Protector station monitor requires no routine maintenance. All seals slide on plastic surfaces and require no periodic greasing.
The swiveling joints use plastic sliding elements that also do not require grease. The Protector should be inspected annually and
after each use.
CAUTION Any alterations to the monitor and its markings could diminish safety and constitutes a misuse
of this product.
9.1 REPAIR
Factory service is available with repair time seldom exceeding one day in our facility. Factory serviced appliances are repaired by
experienced technicians to original specifi cations, fully tested and promptly returned.
Repair parts and service procedures are available for those wishing to perform their own repairs. Task Force Tips assumes no liability
for damage to equipment or injury to personnel that is a result of user service.
For additional information on care, maintenance and testing, refer to: NFPA 1962: Standard for the Care, Use, Inspection,
Service Testing, and Replacement of Fire Hose, Couplings, Nozzles, and Fire Hose Appliances, 2013 Edition
9.2 LOWER SEAL AND VALVE SEAT
If the lower joint leaks externally or the valve does not fully shut off , then the lower seal and/or valve seat may need to be replaced.
To replace these parts:
• Turn off water.
• Remove coupling nut from lower clamp using 5/8” wrench or socket.
• Remove socket head cap screw from lower clamp using 3/8” male hex wrench.
• Separate the joint by pivoting the clamp piece off of the fl anged section.
• Pull out the valve seat and lower seal.
• Clean away dirt on fl anges and clamps.
• Inspect seal and sealing surfaces of valve seat and fl ange.
• Replace damaged parts as needed.
• Apply grease to surface of seal.
• Snap black seal into groove on white valve seat.
• Insert assembly into monitor, white end fi rst.
• Reassemble joint.
• Torque socket head cap screw to 50 ft-lbs prior to installing coupling nut.
• Torque coupling nut to 50 ft-lbs while preventing socket head cap screw from rotating.
9.3 UPPER SWIVEL SEAL AND SWIVEL INSERTS
If the upper swivel leaks or requires excessive force to swivel, then the upper swivel seal and/or plastic swivel inserts may need to
be replaced. To replace these parts:
• Turn off water.
• Remove the cotter pin and then the nut on the locking knob with a ½ inch (13mm) socket.
• Remove the locking knob.
• Separate the joint by pivoting the clamp piece off of the fl anged section.
• Pry out the swivel inserts and inspect for damage.
• Clean away dirt on fl anges and clamps.
• Inspect the seal and sealing surface of the fl ange.
• Replace damaged parts as needed.
• Apply grease to surface of seal.
• Reassemble joint.
10.0 ANSWERS TO YOUR QUESTIONS
We appreciate the opportunity of serving you and making your job easier. If you have any problems or questions, our toll-free
“Hydraulics Hotline”, 800-348-2686, is normally available to you 24 hours a day, 7 days a week.

©Copyright Task Force Tips, Inc. 1999-2017 LIZ-010 December 26, 2017 Rev12
TASK FORCE TIPS, INC.
MADE IN USA • www.tft.com 3701 Innovation Way, Valparaiso, IN 46383-9327 USA
800-348-2686 • 219-462-6161 • Fax [phone]
11.0 INSPECTION CHECKLIST
Monitor must be inspected for proper operation and function according to this checklist before each use. Before fl owing water check:
• All valves (if so equipped) open and close fully and smoothly
• Waterway is clear of obstructions
• There is no damage to any thread or other connection
• All locks and hold-down devices work properly
• The pressure setting on the relief valve (if so equipped) is set correctly
• Gaskets are in good repair
• There is no obvious damage such as missing, broken or loose parts
• There is no damage to the appliance that could impair operation (e.g. dents, cracks or other defects).
• All swiveling elements rotate freely
• Nozzle is securely attached
WARNING Any monitor failing any part of the inspection checklist is unsafe and must have the problem
corrected before use. Operating a monitor that fails any of the above inspections is a misuse of
this equipment.