Taurus Cable pull WS7 User manual

Cable pull WS7
TF-WS7-PULL
TFWS7PULL03.01
Assembly and operating instructions

CablepullWS7
2

CablepullWS7
3
Dear Customer,
Thank you for deciding for a high-quality training equipment of the brand Taurus,
the brand that makes athlete‘s hearts beat faster. Taurus oers a wide range of home
tness equipment like elliptical cross trainers, ergometers, treadmills and rowing
machines. Taurus equipment is the optimal equipment for all those who want to train
at home independent of goals and tness level. For further information please visit
www.sport-tiedje.com or www.taurus-tness.de.
SAFETY NOTICE
Please read all of the instructions carefully before assembly and rst
use. These instructions are intended to ensure speedy assembly and
explain safe usage. Make sure that all people exercising with the
equipment (in particular children and persons with limited physical, sensory, mental or
motor capabilities) are informed about these instructions and its content in advance.
In case of doubt, a responsible person must supervise the use of the equipment.
This equipment has been manufactured according to the latest safety knowledge. As
far as possible, potential safety hazards which could cause injury have been eliminated.
Make sure to follow the instructions carefully and that all parts are securely in place. If
required, read through the instructions again to correct any mistakes.
Please pay close attention to the safety and maintenance instructions given here. The
contract partner cannot be held liable for damage to health, accidents or damage to
the equipment when it is not used in accordance with these instructions.
The equipment is only suitable for use at home. The equipment is not suitable for
semi-professional (e. g., hospitals, clubs, hotels, schools, etc.) and commercial or
professional use (e. g., health clubs).
Retain these instructions in a safe place for future reference, maintenance or when
ordering replacement parts.

CablepullWS7
4

CablepullWS7
5
CONTENTS
1 GENERAL INFORMATION 6
1.1 Technical data 6
2 ASSEMBLY 7
3 ORDERING SPARE PARTS 23
3.1 Service hotline 23
3.2 Serial number and model name 23
3.3 Parts list 24
3.4 Exploded drawing 26

CablepullWS7
6
1 GENERAL INFORMATION
1.1 Technical data
Weight and dimensions:
Item weight (gross, incl. packaging): 40 kg
Item weight (net, without packaging): 35 kg
Packed dimensions (length x width x height):
approx. 1935 mm x 420 mm x 215 mm
Set-up dimensions with Multi-gym WS7 (length x width x height):
approx. 225 cm x 172 cm x 213 cm
Maximum user weight: 150 kg/330 lbs

CablepullWS7
7
 


  
  
       FP




2 ASSEMBLY
We recommend that you do not completely tighten the screws and bolts at rst
in order to make the assembly of the training machine easier. However, please
make sure that all screws and bolts are tightened once the assembly is done.
Screws and cables overview

CablepullWS7
8
 
 
   


 
 






CablepullWS7
9




 













 
Step 1: Exploded drawing
No. Description Note Qty.
20 washer Φ12 14
21 lock nut M12 6
128 connection plate 3
130 spring washer Φ12 2
131 hexagon bolt M12*30 2
132 hexagon bolt M12*80 6
164 connection tube 1
165 pull cable tower back connection tube 1
166 side ground frame 1

CablepullWS7
10
Step 1: Assembly
1.Mount the front connecting tube (164) with two screws M12*30 (131), M12 spring
washers (130), and M12 washers (20) on the main frame.
2. Mount the rear connecting tube (164) with two screws M12*80 (132), M12 washers
(20), M12 lock nuts (21), and the connecting plate (128) on the main frame.
3. Mount the lateral main frame (166) with four screws M12*80 (132), M12 washers
(20), M12 lock nuts (21), and connecting plates (128) on the front and rear connecting
tube.
1.

CablepullWS7
11

















Step 2: Exploded drawing
No. Description Note Qty.
5 washer Φ10 4
20 washer Φ12 8
21 lock nut M12 4
23 lock nut M10 2
43 hexagon bolt M10*70 2
129 arc-shaped 1
131 hexagon bolt M12*30 2
132 hexagon bolt M12*80 2
167 sliding sleeve 1
168 T shape pull pin Φ10 1
No. Description Note Qty.
169 guide tube 1
170 side standing tube 1
171 side elbow tube 1

CablepullWS7
12
Step 2: Assembly
1. Mount the guide rod (169) with two M10*70 screws (43), M10 washers (5), and M10
lock nuts on the lateral main frame.
2. Slide the cable pull roller (167) on the guide rod (169) and screw the T-shaped lock
pin (168) on it.
3. Mount the lateral standpipe (170) with M10*125 screws (133), M12 nuts (21), M12
washers (20), and the connecting plate (129) on the lateral main frame.
4. Mount the lateral angled tube (171) with M12*30 screws (131), M12 washers
(20), and M12 lock nuts (21)
on the lateral standpipe
(170) and the right cover.

CablepullWS7
13








 







Step 3: Exploded drawing
No. Description Note Qty.
5 washer Φ10 14
23 lock nut M10 7
65 hexagon bolt M10*75 7
172 pull cable tower pulley Φ14*50 2
173 pull cable tower cover 1
174 pull cable tower cover 1

CablepullWS7
14
Step 3: Assembly
1. Mount the covers of the cable tower (173, 174) with M10*75 screws (65), M10
washers (5), and M10 nuts (23) on the guide rod, lateral standpipe, and lateral angled
tube.
2. Mount the M14*50 shafts (172) with M10*75 screws (65), M10 washers (5), and M10
nuts (23) on the covers of the cable tower (173, 174).

CablepullWS7
15













Step 4: Exploded drawing
No. Description Note Qty.
5 washer Φ10 8
23 lock nut M10 4
52 hexagon bolt M10*45 1
55 pulley Φ95*26 4
175 hexagon bolt M10*80 3
176 pulley spacer Φ20*Φ 6

CablepullWS7
16
Step 4: Assembly
1. Mount three pulleys (55) with M10*80 screws (175), M10 washers (5), and M10 nuts
(23) on the marked points between the covers of the cable tower.
2. Mount the pulley (55) with a M10*45 screw (52), M10 washer (5), and M10 nut (23)
below the lateral main frame.

CablepullWS7
17

Step 5: Exploded drawing
No. Description Note Qty.
5 washer Φ10 8
23 lock nut M10 5
30 hexagon bolt M10*25 1
52 hexagon bolt M10*45 5
55 pulley Φ95*26 4
59 cable hook 1
142 hexagon bolt 1
177 pulley catch plate M10*50 1
178 movable pulley frame 1
179 pull cable tower short L:5625mm 1

CablepullWS7
18


TF-WS7-PULL
TF-WS7-ATT
Step 5: Exploded drawing

CablepullWS7
19
Step 5: Assembly
1. Replace the cable (70) of step 13 by the cable (179). Pull the cable (179) through the
same guiding path like in step 13. Mount the at, short cable end of the cable tower
(179) with M10*25 screw (30), M10 washer (5), and M10 nut (23) on the lateral main
frame.
2. Mount the pulley (55) with M10*45 screw (52), M10 washer (5), and M10 nut (23).
3. Mount the pulley (55) with M10*50 screw (142), M10 washer (5), M10 nut (23), and
guide hook (177).
4. Connect the cable of the cable tower (179) through M12 washer (20) with the
mobile pulley frame (178).
5. Mount the pulley (55) with M10*45 screw (52), M10 washer (5), and M10 nut (23) on
the mobile pulley frame (178).

CablepullWS7
20

Step 6: Exploded drawing
No. Description Note Qty.
5 washer Φ10 2
23 lock nut M10 1
30 hexagon bolt M10*25 1
60 9 link chain & snap hook 1
85 handle belt 1
180 pull cable tower long L:7290mm 1