Taurus TF-X5.1 User manual

Assembly and operating instructions
Elliptical cross trainer X5.1
Art. No. TF-X5.1

X5.1

2

X5.1
3
Dear Customer,
Thank you for deciding for a high-quality training equipment of the brand Taurus,
the brand that makes athlete‘s hearts beat faster. Taurus oers a wide range of home
tness equipment like elliptical cross trainers, ergometers, treadmills and rowing
machines. Taurus equipment is the optimal equipment for all those who want to train
at home independent of goals and tness level. For further information please visit
www.sport-tiedje.com or www.taurus-tness.de.
SAFETY NOTICE
Please read all of the instructions carefully before assembly and rst
use. These instructions are intended to ensure speedy assembly and
explain safe usage. Make sure that all people exercising with the
equipment (in particular children and persons with limited physical, sensory, mental or
motor capabilities) are informed about these instructions and its content in advance.
In case of doubt, a responsible person must supervise the use of the equipment.
This equipment has been manufactured according to the latest safety knowledge. As
far as possible, potential safety hazards which could cause injury have been eliminated.
Make sure to follow the instructions carefully and that all parts are securely in place. If
required, read through the instructions again to correct any mistakes.
Please pay close attention to the safety and maintenance instructions given here. The
contract partner cannot be held liable for damage to health, accidents or damage to
the equipment when it is not used in accordance with these instructions.
The equipment is only suitable for use at home. The equipment is not suitable for
semi-professional (e. g., hospitals, clubs, hotels, schools, etc.) and commercial or
professional use (e. g., health clubs).
Retain these instructions in a safe place for future reference, maintenance or when
ordering replacement parts.

X5.1

4
CONTENT
1 GENERAL INFORMATION 6
1.1 Technical data 6
1.2 Personal safety 7
1.3 Electrical safety 8
1.4 Set-up place 8
2 ASSEMBLY INSTRUCTIONS, MAINTENANCE AND CARE 9
2.1 General instructions 9
2.2 Errors and error diagnosis 10
2.3 Maintenance and service calendar 11
3 ASSEMBLY 12
3.1 Package contents 12
3.2 Assembly instructions 14
4 OPERATING INSTRUCTIONS 19
4.1 Console display 19
4.2 Button functions 20
4.3 Programs 20
4.3.1 Manual program 22
4.3.2 Training program 23
4.3.3 Watt-controlled program 24
4.3.4 Body fat program 25
4.3.5 Target heart rate program 26
4.3.6 Heart rate controlled program 27
4.3.7 User program 28
5 WORKOUT INSTRUCTIONS 29
5.1 10 tips for eective elliptical cross training 32
5.3 Designing a workout 33
5.4 Stretching exercises for leg & chest muscles 35
5.5 Workout journal 37

X5.1
5
6 WARRANTY INFORMATION 38
7 DISPOSAL 40
8 ORDERING ACCESSORIES 41
9 ORDERING SPARE PARTS 42
9.1 Service hotline 42
9.2 Serial number and model name 42
9.3 Parts list 43
9.4 Exploded drawing 45

X5.1

6
1 GENERAL INFORMATION
1.1 Technical data
LCD display of
+speed in km/h
+cadence (rotations per minute)
+training time in min
+training distance in km
+calories burnt in kcal
+heart rate (when using the hand sensors or a chest strap)
+Watt/resistance level
Resistance system: Electronic magnet brake system
Resistance levels: 24
Total number of training programs: 25
Pre-set programs: 14
Manual program: 1
User dened programs: 4
Heart rate controlled programs: 5
Fat-Test: 1
Balance mass: 5.6 kg
Translation ratio: 1 : 8.25
Stride length: 39 cm
Step height: 18 cm
Step width: 10 cm
Weight and dimensions:
Article weight (gross, including packaging):56 kg
Article weight (net, without packaging): 47 kg
Packaging dimensions (L x W x H): approx. 1450 mm x 450 mm x 770 mm
Set-up dimensions (L x W x H): approx. 1450 mm x 520 mm x 1600 mm
Maximum user weight: 120 kg/264 lbs

X5.1
7
1.2 Personal safety
+Before you start using the equipment, you should consult your physician that
this type of exercise is suitable for you from a health perspective. Particularly
aected are persons who: have a hereditary disposition to high blood pressure
or heart disease, are over the age of 45, smoke, have high cholesterol values, are
overweight and/or have not exercised regularly in the past year.
+Please note that working out excessively can seriously damage your health. Please
also be aware that heart rate monitoring systems might be imprecise.
+The equipment may only be used for its intended purpose; that means for whole
body workouts for adults.
+Any other usage is prohibited and potentially dangerous. The contract partner
cannot be held liable for damage resulting from improper use.
+The equipment is strictly for use by one person at a time.
+Children should not be allowed unsupervised access to the equipment.
+Before starting your training, make yourself familiar with all of the equipment‘s
functions and setting options. Have an expert explain the correct usage of the
product to you.
+Make sure that nobody is in the range of motion of the equipment while exercising.
+Keep your hands, feet and other body parts, hair, clothing, jewelry and other
objects well clear of moving parts.
+During use, wear suitable sports clothing rather than loose or baggy clothing.
When selecting sports shoes, think about the suitability of the sole – preferably
this should be made of rubber or other non-slip materials. Shoes with heels,
leather soles, studs or spikes are not suitable. Never work out in bare feet.
+It is also important to take note of the information given in the workout instructions
for creating a workout plan.
+At the rst signs of weakness, nausea, dizziness, pain, diculty in breathing or
other abnormal symptoms, stop your workout immediately and, if necessary,
consult your physician.
+Without prior agreement from your authorized contract partner, opening the
equipment is prohibited.

X5.1

8
1.3 Electrical safety
+The equipment should be connected directly to a grounded plug socket only by
means of the power cable supplied. The use of multi-socket adapters or similar
is not recommended. Extension leads must comply with local electrical safety
guidelines. Always fully unwind the power cable.
+The outlet should be secured with a fuse with a minimum value of „16 amperes,
slow“.
+In order to reduce the risk of an electric shock, always unplug the equipment from
the mains socket immediately after your workout, before assembly or dismantling,
and before maintenance or cleaning. Do not pull on the cable.
+When plugged in, do not leave the equipment unattended at any time. To avoid
use by anyone unfamiliar with the operating instructions, the power cable should
be removed when the equipment is not in use.
+Keep the power cable away from heat, oil and sharp edges. Do not route the power
cable underneath the equipment or under a carpet or rug, and do not place any
objects on top of it.
+Make no modications to either the power cable or the mains plug.
+If the power cable or the plug are damaged or defective, contact your authorized
contract partner. Do not use the equipment in the meantime.
+Do not keep electrical devices (e. g., mobile phones) in close proximity to the
console or the control electronics, otherwise display values (e. g., pulse measuring)
could be inaccurate.
1.4 Set-up place
+The equipment should only be used indoors, in a suciently heated and dry area
(ambient temperature between 10°C and 35°C). The equipment should not be
used outdoors or in rooms with high humidity (over 70%) like swimming pools.The
equipment should only be stored in surroundings with an ambient temperature
between 5°C and 45°C.
+The training room should be well ventilated during training and not be exposed to
any draughts.
+Choose a location in which to place the equipment such that there is enough free
space/clearance to the front, the rear and to the sides of the equipment (at least
1.50 m). Furthermore, the equipment should not be set up in main entrances or on
escape routes.
+Always keep the power cable away from hot surfaces and grounds and make sure
that the cable is not stuck somewhere or becomes a„trip hazard“.

X5.1
9
+No objects of any type should be inserted into the openings of the equipment.
+The equipment should be placed on a level and solid surface, any unevenness in
the oor should be leveled out.
+A oor protective mat / equipment underlay can help to protect high-quality oor
coverings (parquet, laminate, cork, carpets) from dents and sweat and can help to
level out slight unevenness.
2
2 ASSEMBLY INSTRUCTIONS, MAINTENANCE AND CARE
2.1 General instructions
+Please check if all parts and tools belonging to the equipment are included in the
delivery and if there is any transport damage. If there are any complaints, please
contact your contract partner directly.
+Some of the nuts and bolts to be used in assembly are already pre-mounted in
order to make set-up as easy as possible.
+The equipment must be assembled by adults. In case of doubt, ask for assistance
from another person with technical skills.
+Keep children away from the equipment during assembly, because small parts are
included in the delivery and may be swallowed.
+Make sure that you have enough space (at least 1.50 m) in every direction during
assembly.
+Do not leave any tools and packaging materials like plastic sheeting laying around
to avoid danger of suocation for children.
+Assemble the equipment on an underlay mat or on the cardboard packaging in
order to avoid damage to the equipment and to the oor (scratches).
+Before starting assembly, all individual parts should be placed on the oor next to
each other.
+Read the assembly instructions carefully and assemble the equipment according
to the illustrations. Proceed carefully and cautiously.
+First loosen all parts and check for their correct tting. Then tighten the screws
using a tool.
+Modications to the design or improper repairs may pose a hazard to the user and
should not be carried out. The product warranty may be void as a result.
+Only authorized service technicians are permitted to carry out all servicing and/or
repairs – it excludes maintenance and care.

X5.1

10
+Damaged or worn components may impair your safety and the lifespan of the
equipment. You should therefore immediately replace damaged or worn components.
Please contact your contract partner in such a case. The equipment should no longer be
used until it has been repaired. When needed, only use original Taurus spare parts.
+Check the tightness of all screw connections once a month.
+In order to be able to guarantee the constructively dened safety level of this equipment,
we recommend having the equipment regularly maintained (at least once a year) by
specialists (service technicians of your contract partner).
+The equipment may be cleaned of dust, dirt and sweat using a damp cloth. The use of
solvents should be strictly avoided. Also, make sure that no liquids (e. g. sweat) get into
the openings of the equipment (e. g. console).
2.2 Faults and troubleshooting
The equipment runs through regular quality controls during production. Nevertheless,
errors or malfunctions on the equipment may occur. Individual parts are often the cause
of faults and replacement is usually sucient. Please use the following overview to see
the ve most common errors and how to repair them. If the equipment still does not work
properly, please contact your contract partner.
Problem Cause Solution
Drive discs wobble
or make noises
Drive pulley is loose Tighten nuts
Display does not
work
No plug connection,
power supply not
plugged in
Check all plug connections and see if
the power supply is plugged in
Footplates are
creaking
Footplates are loose Tighten up the footplate screws
Creaking noises Screws are loose Check screws are properly tightened
No pulse reading
• Sources of interference
in the room
• Using a chest strap:
- Unsuitable chest strap
- Chest strap is
incorrectly positioned
- Batteries are empty
oder discharged
• Eliminate sources of interference (e. g.
mobile phone, loudspeaker, etc.)
• Use a suitable chest strap (see
recommended accessories)
• Reposition the chest strap and/or
moisten the electrodes
• Change or charge the batteries

X5.1
11
2.3 Maintenance and service calendar
The following routine work must be done in the specied time intervals:
Part Weekly Monthly Twice a year Annually
Display console C I
Lubricate the moving parts I
Plastic cover C I
Screws and cable connec-
tions I
Legends: C = cleaning; I = inspect

X5.1

12
#104-1
8.7x20x1.5T
Washer (2x)
3 ASSEMBLY
3.1 Package contents
The package contains the parts represented in the illustration, including a power
cable with mains plug. If one of the illustrated parts is missing, please contact your
contract partner.
Step 1:
#112
3/8x23x1.5T
Spring washer (2x)
#96
3/8
Cap nut (2x)
#80-1
5/16x15mm
Allen screw (2x)
#82
M5x15mm
Phillips screw
#77
3/8“x3“
Lock screw
Step 2:
#84
M5x10mm
Phillips screw (4x)
#80
5/16“x15mm
Allen screw (6x)
#82
5/16“x1.5T
Spring ring (6x)
#105
5/16“x23x1.5T
Washer (4x)
#113
5/16“x23x1.5T
Spring washer (2x)

X5.1
13
Step 3:
#74
5/16“x15mm
Hex head screw (2x)
#102
8.7x20x1.5T
Washer (2x)
Step 4:
#113
5/16“23x1.5T
Spring washer (4x)
#91
5/16“x7T
Nylon nut (6x)
#76
5/16“x1-3/4“
Hex head screw (6x)
#87
3.5x12mm
Sheet screw (8x)
Tools
#116
12mm wrench (1x)
#118
5mm Allen screw & Phillips
screwdriver
#115
13 & 14mm wrench

X5.1

14
3.2 Assembly instructions
Before starting assembly, look carefully through the individual assembly steps shown
and assemble the equipment in the order indicated.
Unpacking the machine
(1) Carefully remove all parts from the carton and check the content for missing
or damaged parts. If parts are missing or damaged, contact your contract partner
immediately.
(2) Take the tools out of the screw and tool set. The screw set is divided according to
the steps of assembly. In order to avoid confusion, only take out the parts that you
need for the next step.
Step 1: Assembly of front supporting foot and pedal bars
(1) Mount the front supporting foot (14) on the plate, which is located on the lower
end of the frame, with two carriage bolts (77), two spring washers (112) and two cap
nuts. The transport wheels must point forward.
(2) Mount the two wheel covers (65) on the left and right pedal arm (5) with four
Phillips screws (82).
(3) Slide the shaft of the left pedal bar (7) into the socket of the left pedal arm (5) and
mount it with an Allen screw (80-1), a washer (104-1). Repeat the process for the right
side.

X5.1
15
Step 2: Assembly console mast
(1) Guide the console cable (36) with cable ties through the console mast (11) and pull
it through the console bracket plate. Insert the console mast in the frame and mount
it with six Allen screws (80), six spring rings (111), four washers (105) and two spring
washers (113).
(2) Remove the cable ties from the console cables (36) and insert the computer cable
and the two hand pulse cables into the console. Mount the console (35) on the bracket
plate with four Phillips screws (84). Make sure that the cables are not stuck.

X5.1

16
Step 3: Assembly of arm bars
(1) Mount the left arm bar (9) on the left shaft and the right arm bar (10) on the right
shaft of the console mast (11) with two hex head screws (74) and two washers (102).
(2) Loosen the axles (18) from the two pedal bars. Mount the pedal bars on the arm
bars each with an axle (18), a screw (80-1) and a washer (105-1).

X5.1
17
Step 4: Assembly of arm bars
(1) Mount the left (15) and right (16) arm bars on the pedal arms with six hex head
screws (76), four spring washers (113) and six nylon nuts (91).
(2) Mount the front (L)(69) and rear arm bar cover (L)(69~1) together on the left arm
bar with three sheet screws (87).
Repeat the process for the right side.
(3) Mount the left (L)(42) and right (R)(43) console mast cover on the console mast
with two sheet screws (87).
Then check again to see if all screws and nuts have been tightened.

X5.1

18
Lubrication
Apply two 2cc of lubricant
under the middle of the rail.
Lubricant should be applied
every three months.
If you notice that the movement
is not so soft and smooth or
there are noises, then apply 2cc
of lubricant on the middle of
the rail as well.
Transport
The equipment has two
transport wheels which you
can use to easily move the
equipment if you lift the
equipment on the lower end.

X5.1
19
4 OPERATING INSTRUCTIONS
4.1 Console display
CALORIES
Energy consumption in kcal
Note about the measurement of calories burnt:
The calculation of calories burnt is based on a general
formula. It is not possible to exactly determine
individual calories burnt, because diverse personal
data is required for this.
TIME (Zeit) Training time
TARGET HR Denition of the target heart rate by the user
HEART RATE Heart rate in BPM
SPEED Speed in km/h
RPM Rotations per minute
ODO Total distance

X5.1

20
DISTANCE Training distance
WATT Resistance in Watt
LEVEL Level of diculty 1 – 24
PROGRAM Display of program proles
4.2 Button functions
START/STOP
1. Starting and ending a program
2. Starts the body fat measuring
3. Hold the button for three seconds in order to reset all values to
zero
UP/DOWN Increase or decrease training parameters. You can adjust the
resistance level with this button while training.
ENTER Button to conrm settings.
RECOVERY
Press this button to determine your recovery heart rate. After one
minute, your tness level will be displayed with a grade between
1 and 6.
MODE Press this button to change between RPM and SPEED, ODO and
DISTANCE or WATT and CALORIES while training.
4.3 Programs
After turning on the equipment, use the arrow buttons (UP/DOWN) to select a training
program from the following categories and conrm with ENTER.
• Manual
• Pre-Programs (training programs
• Watt Program
• Body Fat Program
• Target Heart Rate Program
• Heart Rate Control Program
• User Program