tayco Kip User manual

Kip
installation guide
February 2020

for more information, contact Installation Service
toll free I 1.800.675.4092
Mon - Fri I 8:30 am – 5:00 pm EST
www.tayco.com

Table of Contents
General Instructions 1|03
Installation Checklist ................................................................................................................ 1
Care and Maintenance ............................................................................................................. 2
Application Guide ..................................................................................................................... 3
Kip Community Tables 04|19
Kip Community Table – 1 Surface ........................................................................................... 04
Kip Community Table – 2 Surfaces ......................................................................................... 13

Installation Checklist
Perform a site inspection prior to the installation date to check existing site conditions and identify constraints and
limitations that could possibly cause delays or problems during the actual installation.
SITE ACCESSIBILITY
1. Verify existing loading facilities and proximity of loading dock to staging area.
2. Verify if receiving area is accessible by trailer.
3. Verify access to service elevators.
4. Reserve service elevators in advance, if necessary.
SITE PREPARATION
1. Clear all obstacles that could interfere with the installation process.
2. When doing a reconfiguration, ensure that all furniture to be re-used are clear of computers, accessories,
books, papers and all personal effects.
3. Ensure that all live wires and data/communications wires are disconnected prior to installation.
FURNITURE PLANS
1. Labeled furniture plans for installation purposes are located in the hardware box. Ensure that drawings are
complete and handy before beginning installation.
STAGING
1. If damages are noticed upon opening the trailer, these must be noted by the receiver on the Bill of Lading.
Also note any imperfections or missing components discovered while unpacking the furniture. This
information is necessary when requesting for product replacement and shipping claims.
2. Unpack products in the general order of installation (refer to Installation Sequence).
WASTE MANAGEMENT
1. Establish a trash removal area separate from the product staging area.
FEBRUARY 2020
kip 1

Care & Maintenance
Laminates
Dust laminated surfaces for regular maintenance. Clean any dirt or stain with a damp cloth. Do not use an excessive
amount of water, abrasive cleaners, acids or alkalis and do not scratch or scrape surfaces. For persistent stains and
marks use a commercial cleaner, such as Cabinet Magic® or Countertop Magic®, both manufactured by Magic
American Corporation.
Painted Metals
Tayco’s painted metal products are powder-paint-coated. To clean these products, use a damp cloth, using only a
small amount of lukewarm water if necessary. Dry with a clean a dry cloth. To avoid scratching and damaging the
painted surface, do not use hard bristled brushes or abrasive.
THE USE OF HARSH CLEANERS AND CHEMICALS MAY PERMANENTLY ALTER THE PRODUCT FINISH APPEARANCE AND
WILL VOID WARANTY.
FEBRUARY 2020
kip 2

022020
WIDTH
DEPTH
[E]
[D]
[D]
[A]
[B]
[C]
[C]
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
DIMENSIONS ARE IN
INCHES [ mm] UNLESS
OTHERWISE SPECIFIED
PROJECT CODE - FOR SPECIALS ONLY
Dec 05, 2019
DESCRIPTION
PART NUMBER
SCALE
REV.
REFERENCE DRAWING
TAYCO
PANELINK LTD
TOLERANCE
MATERIAL
FINISH APPROVED BY
± 0.015" [0.38mm]
UNLESS SPECIFIED
1:8
TAYCO STANDARD FINISH
APPROVED DATE
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
jmahardi
DRAWN DATE
PRODUCT LINE
SCALE
REV.
00
PARSONS TABLE SIZE CHART FOR ONE-SECTION
SURFACES
PG 1 OF 2
RIDEAU
THIRD ANGLE PROJECTION
`` THIS DOCUMENT IS THE PROPERTY OF TAYCO PANELINK LTD. AND CONTAINS CONFIDENTIAL AND/OR PROPRIETARY INFORMATION . THE CONTENTS OF THIS DOCUMENT ARE NOT TO
BE REPRODUCED, DISTRIBUTED, EXAMINED BY THIRD PARTY OR DIVULGED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION FROM TAYCO PANELINK LTD. ``
DRAWN BY
C:\Tayco PDM\RIDEAU\RIDEAU PARSONS
TABLE\ASSEMBLIES, R-PT2X\
--
Order No. - FOR SPECIALS ONLY
WIDTH
DEPTH
[E]
[D]
[F]
[C]
[C]
[A] [A]
[B]
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
DIMENSIONS ARE IN
INCHES [ mm] UNLESS
OTHERWISE SPECIFIED
PROJECT CODE - FOR SPECIALS ONLY
Dec 03, 2019
DESCRIPTION
PART NUMBER
SCALE
REV.
REFERENCE DRAWING
TAYCO
PANELINK LTD
TOLERANCE
MATERIAL
FINISH APPROVED BY
± 0.015" [0.38mm]
UNLESS SPECIFIED
1:10
TAYCO STANDARD FINISH
APPROVED DATE
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
jmahardi
DRAWN DATE
PRODUCT LINE
SCALE
REV.
00
PARSONS TABLE SIZE CHART FOR TWO-SECTION
SURFACES
PG 2 OF 2
RIDEAU
THIRD ANGLE PROJECTION
`` THIS DOCUMENT IS THE PROPERTY OF TAYCO PANELINK LTD. AND CONTAINS CONFIDENTIAL AND/OR PROPRIETARY INFORMATION . THE CONTENTS OF THIS DOCUMENT ARE NOT TO
BE REPRODUCED, DISTRIBUTED, EXAMINED BY THIRD PARTY OR DIVULGED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION FROM TAYCO PANELINK LTD. ``
DRAWN BY
C:\Tayco PDM\RIDEAU\RIDEAU PARSONS
TABLE\ASSEMBLIES, R-PT2X\
--
Order No. - FOR SPECIALS ONLY
Leg Positioning
Tables longer than 96”W include a mid-gable
Mid-gables are inset by 3” from the table edge
72”-96”W
One Piece
No Mid-Gable
108”-144”W
Two Pieces
With Mid-Gable
Kip
Width
(IN)
Depth
(IN)
# of
Surfaces
A (IN) B (IN) C (IN) D (IN) E (IN)
60 30 1 30 15 16 8.25 13.5
60 36 1 30 18 16 11.25 13.5
72 30 1 36 15 22 8.25 13.5
72 36 1 36 18 22 11.25 13.5
72 42 1 36 21 22 14.25 13.5
84 30 1 42 15 28 8.25 13.5
84 36 1 42 18 28 11.25 13.5
84 42 1 42 21 28 14.25 13.5
96 30 1 48 15 34 8.25 13.5
96 36 1 48 18 34 11.25 13.5
96 42 1 48 21 34 14.25 13.5
Width
(IN)
Depth
(IN)
# of
Surfaces
A (IN) B (IN) C (IN) D (IN) E (IN) F (IN) G (IN)
108 36 2 27.38 18 27.38 11.25 29.94 3.03 13.5
108 42 2 27.38 21 27.38 14.25 35.94 3.03 13.5
120 36 2 30.38 18 30.38 11.25 29.94 3.03 13.5
120 42 2 30.38 21 30.38 14.25 35.94 3.03 13.5
132 36 2 33.38 18 33.38 11.25 29.94 3.03 13.5
132 42 2 33.38 21 33.38 14.25 35.94 3.03 13.5
144 36 2 36.38 18 36.38 11.25 29.94 3.03 13.5
144 42 2 36.38 21 36.38 14.25 35.94 3.03 13.5
A – Width of table edge to center power unit
B – Depth of table edge to center power unit
C – Table edge to optional side mount USB
D – Table edge to bridge
E – Bridge depth
F – Mid-gable offset
G – Mid-gable depth
A/C
A/C
A
A/C
A/C
D
D
E
F
G
B
D
D
E
B
Kip I Application Guide
FEBRUARY 2020
kip 3

Kip community table – 1 Surface
Figure 1
Figure 2
Tools & Hardware Needed
13. Place the surface face down on
a clean solid surface or floor
with the underside facing up,
(Figure 1).
14. Position the bridge on the
surface, (Figure 2).
Continued on the next page >>
FEBRUARY 2020
kip 4

Kip community table – 1 Surface
Figure 3
Figure 4
Tools & Hardware Needed
8540-1278 8540-0770_Dowel
Drill
Rubber Mallet
Philips Bit
Combi Dowel (6X) Wooden Dowel (4X)
15. Attach the combi dowels by
screwing them into the pre-
bored holes, (Figure 3).
16. Insert the wooden dowels,
(Figure 4).
Continued on the next page >>
FEBRUARY 2020
kip 5

Kip community table – 1 Surface
Figure 5
Figure 6
Figure 7
Tools & Hardware Needed
8540-0644_CAM
Flat Screw Driver CamFix (12X)
17. Insert the CamFix into the holes
of the gables, (Figure 5).
18. Connect the gable to surface
and press the boards together
by inserting the combi dowels
and wooden dowels into the
holes of the gables, (Figure 6).
19. Turn the CamFix to smoothly
lock the gable and surface
together, (Figure 7).
20. Stick fast caps to the exposed
CamFix, (Figure 7).
Continued on the next page >>
FEBRUARY 2020
kip 6

Kip community table – 1 Surface
Figure 8
Tools & Hardware Needed
8540-0789_SCREW 8540-1280
Drill Robertson # 2 Hex Bit #10 X 1" Pan Head
Screw (1X) 1/4-20 X 35MM JCB Bolt (2X)
21. Screw 1/4-20 X 35mm JCB bolts
into the two holes at the corner
of the bridge exposing an inch
of the bolt, (Figure 8).
22. Set-in the topmost hole of the
gable cover mount channel
using one #10 X 1” Pan Head
Screw into the pre-drilled hole.
Note: Do not tighten the screw
so you can easily swing the
gable cover mount channel,
(Figure 8).
23. Swing the gable cover mount
channel until the slots touch
the JCB bolts, (Figure 8).
Continued on the next page >>
FEBRUARY 2020
kip 7

Kip community table – 1 Surface
Figure 9
Figure 10
Tools & Hardware Needed
8540-0789_SCREW 8540-1280
Drill Robertson # 2 Hex Bit #10 X 1" Pan Head
Screw (19X)
1/4-20 X 35MM JCB
Bolt (6X)
24. Align and flush the gable cover
mount channel to the side face
of the bridge before tightening
the screws, (Figure 9).
25. Tighten the 1/4-20 X 35mm JCB
bolts, (Figure 10).
26. Securely fasten the gable cover
mount channel, using #10 X 1”
Pan Head Screws into the pre-
drilled holes of the gable,
(Figure 10).
27. Follow Steps 6 to 14 to install
the other gable and for each
gable cover mount channel
required.
Continued on the next page >>
FEBRUARY 2020
kip 8

Kip community table – 1 Surface
Figure 11
Figure 12
Tools & Hardware Needed
8540-0789_SCREW
Drill Robertson # 2 #10 X 1" Pan Head
Screw
28. Securely fasten the bridge to
the surface, using #10 X 1” Pan
Head Screws, (Figure 11).
29. Securely fasten the bridge to
gable, using #10 X 1” Pan Head
Screws, (Figure 12).
30. Lift the table into an upright
position; level and adjust the
glides if necessary.
Continued on the next page >>
FEBRUARY 2020
kip 9

Kip community table – 1 Surface
Figure 13
Figure 13A
Tools & Hardware Needed
8540-0789_SCREW
Drill Robertson # 2 #10 X 1" Pan Head
Screw
WARNING – To reduce the risk of
fire, electric shock, or injury to
persons:
 For indoor use only.
 Do not use with extension
cords.
 Do not try to open the unit
for any reason.
31. Set the power grommet into
the hole and then secure it with
mounting screws provided,
(Figure 13).
Note: Make sure that the unit
is securely installed to the
mounting surface.
32. Affix the faceplate by pressing
it against the main unit.
33. Place the USB charger on the
desired surface and use two
screws to fasten it onto the
wood surface.
Note: USB chargers are extra.
34. Lay-in the electrical wires and
communication cables inside
wire troughs, (Figure 13A).
35. Plug the power cord(s) or
adapter to nearest wall or floor
outlet.
Continued on the next page >>
FEBRUARY 2020
kip 10

Kip community table – 1 Surface
Figure 14
Figure 15
Tools & Hardware Needed
8485-0275 8540-0545
Drill Robertson # 2 Gable Cover
Bracket (4X) #10 X 11/16" Oval Head Screw (8X)
36. Attach the gable cover
brackets, using #10 X 11/16”
Oval Head Screws into the pre-
drilled holes of the gable cover,
(Figure 14).
Repeat this procedure for each
gable cover required.
37. Angle the gable cover at 30
degrees; place the gable cover
brackets into the cutouts of
gable cover mount channels
and push the gable cover
gently, (Figure 15).
Repeat this procedure for the
other gable cover.
Continued on the next page >>
FEBRUARY 2020
kip 11

Kip community table – 1 Surface
Figure 16
Tools & Hardware Needed
8540-1280
Drill Hex Bit
1/4
-
20 X 35MM
JCB BOLT (8X)
38. Attach the bridge cover to
bridge, using 1/4-20 X 35mm
JCB bolts, (Figure 16).
FEBRUARY 2020
kip 12

Kip community table – 2 Surfaces
Figure 1
Tools & Hardware Needed
8540-0770_Dowel
Rubber Mallet
Wooden Dowel (2X)
1. Place the surfaces on a clean
solid surface or floor with the
underside facing up; level the
two surfaces and attach them
together by inserting wooden
dowels, (Figure 1).
Continued on the next page >>
FEBRUARY 2020
kip 13

Kip community table – 2 Surfaces
Figure 2
Figure 3
Tools & Hardware Needed
8540-0789_SCREW MENDPLATE-BLK
Drill
Rubber Mallet
Robertson # 2
#10 X 1" Pan Head
Screw (8X) Top Bolt (4X)
Mending Plate (2X)
2. Place the top bolt into the
groove. Tighten the bolt using
a box wrench, (Figure 2).
3. Attach the mending plates,
using #10 X 1” Pan Head
Screws, (Figure 2).
4. Position the bridge on the
surface, (Figure 3).
Continued on the next page >>
FEBRUARY 2020
kip 14

Kip community table – 2 Surfaces
Figure 4
Figure 5
Tools & Hardware Needed
8540-1278 8540-0644_CAM
Drill Flat Screw Driver
Phi
l
lips Bit
Combi Dowel, (8X) CamFix (20X)
5. Attach the combi dowels by
screwing them into the pre-
bored holes, (Figure 4).
6. Insert the CamFix into the holes
of the gables, (Figure 5).
Continued on the next page >>
FEBRUARY 2020
kip 15

Kip community table – 2 Surfaces
Figure 6
Figure 7
Tools & Hardware Needed
Flat Screw Driver
7. Connect the mid gable first to
surface and press the boards
together by inserting the combi
dowels into the holes of the
gable, (Figure 6).
8. Turn the CamFix on both sides
of the mid gable to smoothly
lock the gables and surface
together, (Figure 7).
9. Stick fast caps to the exposed
CamFix, (Figure 7).
Continued on the next page >>
FEBRUARY 2020
kip 16

Kip community table – 2 Surfaces
Figure 8
Figure 9
Tools & Hardware Needed
8540-0789_SCREW 8540-1280
Drill Robertson # 2 Hex Bit #10 X 1" Pan Head
Screw
1/4
-
20 X 35MM
JCB BOLT (8X)
10. Please refer to pages 6- 8.
Follow Steps 6 - 14 to install
the end gables, (Figure 8).
Repeat this procedure to install
the other end gable, (Figure 9).
Continued on the next page >>
FEBRUARY 2020
kip 17