tayco Norris Series User manual

Norris
installation guide
February 2020

for more information, contact Installation Service
toll free I 1.800.675.4092
Mon - Fri I 8:30 am – 5:00 pm EST
www.tayco.com

Table of Contents
General Instructions 1|02
Installation Checklist ................................................................................................................ 1
Care and Maintenance ............................................................................................................. 2
Application Guide ..................................................................................................................... 3
Norris Boardroom Tables 5|14
Norris Boardroom Table – 1 Surface ......................................................................................... 5
Norris Boardroom Table – 2 Surfaces ..................................................................................... 10
Norris Boardroom Table – 3 Surfaces ..................................................................................... 14

Installation Checklist
Perform a site inspection prior to the installation date to check existing site conditions and identify constraints and
limitations that could possibly cause delays or problems during the actual installation.
SITE ACCESSIBILITY
1. Verify existing loading facilities and proximity of loading dock to staging area.
2. Verify if receiving area is accessible by trailer.
3. Verify access to service elevators.
4. Reserve service elevators in advance, if necessary.
SITE PREPARATION
1. Clear all obstacles that could interfere with the installation process.
2. When doing a reconfiguration, ensure that all furniture to be re-used are clear of computers, accessories,
books, papers and all personal effects.
3. Ensure that all live wires and data/communications wires are disconnected prior to installation.
FURNITURE PLANS
1. Labeled furniture plans for installation purposes are located in the hardware box. Ensure that drawings are
complete and handy before beginning installation.
STAGING
1. If damages are noticed upon opening the trailer, these must be noted by the receiver on the Bill of Lading.
Also note any imperfections or missing components discovered while unpacking the furniture. This
information is necessary when requesting for product replacement and shipping claims.
2. Unpack products in the general order of installation (refer to Installation Sequence).
WASTE MANAGEMENT
1. Establish a trash removal area separate from the product staging area.
FEBRUARY 2020
norris 1

Care & Maintenance
Laminates
Dust laminated surfaces for regular maintenance. Clean any dirt or stain with a damp cloth. Do not use an excessive
amount of water, abrasive cleaners, acids or alkalis and do not scratch or scrape surfaces. For persistent stains and
marks use a commercial cleaner, such as Cabinet Magic® or Countertop Magic®, both manufactured by Magic
American Corporation.
Painted Metals
Tayco’s painted metal products are powder-paint-coated. To clean these products, use a damp cloth, using only a
small amount of lukewarm water if necessary. Dry with a clean a dry cloth. To avoid scratching and damaging the
painted surface, do not use hard bristled brushes or abrasive.
THE USE OF HARSH CLEANERS AND CHEMICALS MAY PERMANENTLY ALTER THE PRODUCT FINISH APPEARANCE AND
WILL VOID WARANTY.
FEBRUARY 2020
norris 2

Norris
WIDTH
DEPTH
[B]
[A] [G]
[F]
[C]
[B]
[D]
[E]
TYPICAL TABLE 4
204W - 240W
DEPTH
[G]
[F]
WIDTH
[A]
[B]
[C]
[B]
[D]
TYPICAL TABLE 3
132W - 192W
DEPTH
[G]
WIDTH
[A]
[B]
[C]
[B]
[D]
TYPICAL TABLE 2
108W - 120W
[G] [A]
WIDTH
DEPTH
[B]
[C]
[B]
[E]
TYPICAL TABLE 1
72W - 96W
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
DIMENSIONS ARE IN
INCHES [ mm] UNLESS
OTHERWISE SPECIFIED
PROJECT CODE - FOR SPECIALS ONLY
Dec 06, 2019
DESCRIPTION
PART NUMBER
SCALE
REV.
REFERENCE DRAWING
TAYCO
PANELINK LTD
TOLERANCE
MATERIAL
FINISH APPROVED BY
± 0.015" [0.38mm]
UNLESS SPECIFIED
TAYCO STANDARD FINISH
APPROVED DATE
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
jmahardi
DRAWN DATE
PRODUCT LINE
SCALE
REV.
00
BOARDROOM TABLE SIZE CHART, TYPICAL
CONFIGURATONS
RIDEAU
THIRD ANGLE PROJECTION
`` THIS DOCUMENT IS THE PROPERTY OF TAYCO PANELINK LTD. AND CONTAINS CONFIDENTIAL AND/OR PROPRIETARY INFORMATION . THE CONTENTS OF THIS DOCUMENT ARE NOT TO
BE REPRODUCED, DISTRIBUTED, EXAMINED BY THIRD PARTY OR DIVULGED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION FROM TAYCO PANELINK LTD. ``
DRAWN BY
C:\Tayco PDM\RIDEAU\RIDEAU BOARDROOM\FINAL
ASSEMBLIES\R-BS1E, STRAIGHT W POWER\
--
Order No. - FOR SPECIALS ONLY
PG. 1 OF 2
WIDTH
DEPTH
[B]
[A] [G]
[F]
[C]
[B]
[D]
[E]
TYPICAL TABLE 4
204W - 240W
DEPTH
[G]
[F]
WIDTH
[A]
[B]
[C]
[B]
[D]
TYPICAL TABLE 3
132W - 192W
DEPTH
[G]
WIDTH
[A]
[B]
[C]
[B]
[D]
TYPICAL TABLE 2
108W - 120W
[G] [A]
WIDTH
DEPTH
[B]
[C]
[B]
[E]
TYPICAL TABLE 1
72W - 96W
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
DIMENSIONS ARE IN
INCHES [ mm] UNLESS
OTHERWISE SPECIFIED
PROJECT CODE - FOR SPECIALS ONLY
Dec 06, 2019
DESCRIPTION
PART NUMBER
SCALE
REV.
REFERENCE DRAWING
TAYCO
PANELINK LTD
TOLERANCE
MATERIAL
FINISH APPROVED BY
± 0.015" [0.38mm]
UNLESS SPECIFIED
TAYCO STANDARD FINISH
APPROVED DATE
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
jmahardi
DRAWN DATE
PRODUCT LINE
SCALE
REV.
00
BOARDROOM TABLE SIZE CHART, TYPICAL
CONFIGURATONS
RIDEAU
THIRD ANGLE PROJECTION
`` THIS DOCUMENT IS THE PROPERTY OF TAYCO PANELINK LTD. AND CONTAINS CONFIDENTIAL AND/OR PROPRIETARY INFORMATION . THE CONTENTS OF THIS DOCUMENT ARE NOT TO
BE REPRODUCED, DISTRIBUTED, EXAMINED BY THIRD PARTY OR DIVULGED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION FROM TAYCO PANELINK LTD. ``
DRAWN BY
C:\Tayco PDM\RIDEAU\RIDEAU BOARDROOM\FINAL
ASSEMBLIES\R-BS1E, STRAIGHT W POWER\
--
Order No. - FOR SPECIALS ONLY
PG. 1 OF 2
Specifying Tops & Plinths
Tables are specified as follows:
- One Piece Top without Plinth: 72”-96”W x 36”-48”D
- Two Piece Top without Plinth: 108”-120”W x 42”-60”D
- Two Piece with Plinth: 132”-192”W x 48”-60”D
- Three Piece Top with Plinth: 216”-240”W x 48”-60”D
72”-96”W
One Piece
No Plinth
108”-120”W
Two Pieces
No Plinth
Width
(IN)
Depth
(IN)
# of
Surfaces
A (IN) B (IN) C (IN) D (IN) E (IN) F (IN) G (IN)
72 36 1 17.25 8 20 N/A 36 N/A 4.5
72 42 1 17.25 9 24 N/A 36 N/A 4.5
84 36 1 17.25 8 20 N/A 42 N/A 4.5
84 42 1 17.25 9 24 N/A 42 N/A 4.5
84 48 1 17.25 11 26 N/A 42 N/A 4.5
96 36 1 17.25 8 20 N/A 48 N/A 4.5
96 42 1 17.25 9 24 N/A 48 N/A 4.5
96 48 1 17.25 11 26 N/A 48 N/A 4.5
Width
(IN)
Depth
(IN)
# of
Surfaces
A (IN) B (IN) C (IN) D (IN) E (IN) F (IN) G (IN)
108 42 2 17.25 9 24 30.02 N/A N/A 4.5
108 48 2 17.25 11 26 30.02 N/A N/A 4.5
108 60 2 17.25 11 38 30.02 N/A N/A 4.5
120 42 2 17.25 9 24 30.02 N/A N/A 4.5
120 48 2 17.25 11 26 30.02 N/A N/A 4.5
120 60 2 17.25 11 38 30.02 N/A N/A 4.5
A – Width of table edge to gable
B – Depth of table edge to gable
C – Gable width
D – Table edge to power grommet
E – Table edge to center power grommet
F – Center plinth width
G – Gable thickness
Norris I Application Guide
FEBRUARY 2020
norris 3

022020
WIDTH
DEPTH
[B]
[A] [G]
[F]
[C]
[B]
[D]
[E]
TYPICAL TABLE 4
204W - 240W
DEPTH
[G]
[F]
WIDTH
[A]
[B]
[C]
[B]
[D]
TYPICAL TABLE 3
132W - 192W
DEPTH
[G]
WIDTH
[A]
[B]
[C]
[B]
[D]
TYPICAL TABLE 2
108W - 120W
[G] [A]
WIDTH
DEPTH
[B]
[C]
[B]
[E]
TYPICAL TABLE 1
72W - 96W
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
DIMENSIONS ARE IN
INCHES [ mm] UNLESS
OTHERWISE SPECIFIED
PROJECT CODE - FOR SPECIALS ONLY
Dec 06, 2019
DESCRIPTION
PART NUMBER
SCALE
REV.
REFERENCE DRAWING
TAYCO
PANELINK LTD
TOLERANCE
MATERIAL
FINISH APPROVED BY
± 0.015" [0.38mm]
UNLESS SPECIFIED
TAYCO STANDARD FINISH
APPROVED DATE
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
jmahardi
DRAWN DATE
PRODUCT LINE
SCALE
REV.
00
BOARDROOM TABLE SIZE CHART, TYPICAL
CONFIGURATONS
RIDEAU
THIRD ANGLE PROJECTION
`` THIS DOCUMENT IS THE PROPERTY OF TAYCO PANELINK LTD. AND CONTAINS CONFIDENTIAL AND/OR PROPRIETARY INFORMATION . THE CONTENTS OF THIS DOCUMENT ARE NOT TO
BE REPRODUCED, DISTRIBUTED, EXAMINED BY THIRD PARTY OR DIVULGED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION FROM TAYCO PANELINK LTD. ``
DRAWN BY
C:\Tayco PDM\RIDEAU\RIDEAU BOARDROOM\FINAL
ASSEMBLIES\R-BS1E, STRAIGHT W POWER\
--
Order No. - FOR SPECIALS ONLY
PG. 1 OF 2
132”-192”W
Two Pieces
With Plinth
204”-240”W
Three Pieces
With Plinth
WIDTH
DEPTH
[B]
[A] [G]
[F]
[C]
[B]
[D]
[E]
TYPICAL TABLE 4
204W - 240W
DEPTH
[G]
[F]
WIDTH
[A]
[B]
[C]
[B]
[D]
TYPICAL TABLE 3
132W - 192W
DEPTH
[G]
WIDTH
[A]
[B]
[C]
[B]
[D]
TYPICAL TABLE 2
108W - 120W
[G] [A]
WIDTH
DEPTH
[B]
[C]
[B]
[E]
TYPICAL TABLE 1
72W - 96W
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
DIMENSIONS ARE IN
INCHES [ mm] UNLESS
OTHERWISE SPECIFIED
PROJECT CODE - FOR SPECIALS ONLY
Dec 06, 2019
DESCRIPTION
PART NUMBER
SCALE
REV.
REFERENCE DRAWING
TAYCO
PANELINK LTD
TOLERANCE
MATERIAL
FINISH APPROVED BY
± 0.015" [0.38mm]
UNLESS SPECIFIED
TAYCO STANDARD FINISH
APPROVED DATE
D
C
B
A
A
B
C
D
1 2 3
4
5
6
7
8
8
7
6
5
4
3 2
1
jmahardi
DRAWN DATE
PRODUCT LINE
SCALE
REV.
00
BOARDROOM TABLE SIZE CHART, TYPICAL
CONFIGURATONS
RIDEAU
THIRD ANGLE PROJECTION
`` THIS DOCUMENT IS THE PROPERTY OF TAYCO PANELINK LTD. AND CONTAINS CONFIDENTIAL AND/OR PROPRIETARY INFORMATION . THE CONTENTS OF THIS DOCUMENT ARE NOT TO
BE REPRODUCED, DISTRIBUTED, EXAMINED BY THIRD PARTY OR DIVULGED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN AUTHORIZATION FROM TAYCO PANELINK LTD. ``
DRAWN BY
C:\Tayco PDM\RIDEAU\RIDEAU BOARDROOM\FINAL
ASSEMBLIES\R-BS1E, STRAIGHT W POWER\
--
Order No. - FOR SPECIALS ONLY
PG. 1 OF 2
Norris
Width
(IN)
Depth
(IN)
# of
Surfaces
A (IN) B (IN) C (IN) D (IN) E (IN) F (IN) G (IN)
132 48 2 17.5 11 26 30.27 N/A 38 4.5
132 60 2 17.5 11 38 30.27 N/A 38 4.5
144 48 2 23.5 11 26 36.27 N/A 38 4.5
144 60 2 23.5 11 38 36.27 N/A 38 4.5
156 48 2 24 11 26 36.77 N/A 38 4.5
156 60 2 24 11 38 36.77 N/A 38 4.5
168 48 2 24 11 26 36.77 N/A 38 4.5
168 60 2 24 11 38 36.77 N/A 38 4.5
180 48 2 24 11 26 36.77 N/A 38 4.5
180 60 2 24 11 38 36.77 N/A 38 4.5
192 48 2 24 11 26 36.77 N/A 38 4.5
192 60 2 24 11 38 36.77 N/A 38 4.5
Width
(IN)
Depth
(IN)
# of
Surfaces
A (IN) B (IN) C (IN) D (IN) E (IN) F (IN) G (IN)
204 48 3 24 11 26 36.77 102 38 4.5
204 60 3 24 11 38 36.77 102 38 4.5
216 48 3 24 11 26 36.77 108 38 4.5
216 60 3 24 11 38 36.77 108 38 4.5
228 48 3 24 11 26 36.77 114 38 4.5
228 60 3 24 11 38 36.77 114 38 4.5
240 48 3 24 11 26 36.77 120 38 4.5
240 60 3 24 11 38 36.77 120 38 4.5
Norris I Application Guide
FEBRUARY 2020
norris 4

Norris boardroom table – 1 Surface
Figure 1
Tools & Hardware Needed
Note: The procedure below is for
Boat, Straight, Super Ellipse and
Video boardroom tables.
1. Place the table top face down
on a clean solid surface or
floor; Position the bridge to
table top, (Figure 1).
Continued on the next page >>
FEBRUARY 2020
norris 5

Norris boardroom table – 1 Surface
Figure 2
Figure 3
Tools & Hardware Needed
8540-0789_SCREW 8540-1282
Drill Box Wrench Robertson # 2 #10 X 1" Pan Head
Screw (6X)
3/8-16" X 1-1/2"
Hex Bolt (8X)
2. To install the table base; position
and attach the steel gable to
bridge, using 3/8-16” X 1 1/2”
Hex bolt, (Figure 2).
Repeat this procedure to install
the other steel gable.
Note: The steel gables for Video
boardroom tables have two
different sizes. The wide one is
for the wider side of the surface.
3. Position the base using the pre-
drilled positioning holes and
attach it to table top using #10 X
1” Oval Head Screw, (Figure 3).
Continued on the next page >>
FEBRUARY 2020
norris 6

Norris boardroom table – 1 Surface
Figure 4
Figure 5
Tools & Hardware Needed
8540-0789_SCREW
Drill Robertson # 2 #10 X 1" Pan Head
Screw (12X)
4. Securely fasten the base, using
#10 X 1” Pan Head Screws,
(Figure 4).
5. Lift the table into an upright
position; level and adjust the
glides if necessary.
6. Set the power grommet into
the hole of the table top and
lay the electrical wires and
communication cables in the
bridge and gables, (Figure 5).
Continued on the next page >>
FEBRUARY 2020
norris 7

Norris boardroom table – 1 Surface
Figure 6
Figure 7
Tools & Hardware Needed
8540-1279 8485-0274 8540-0789_SCREW 8540-0587
Drill Robertson # 2 ‘V’ Knuckle Strike
(4X)
Z- Bracket (4X) #10 X 11/16" Pan
Head Screw (8X)
#6 X 5/8" Pan Head
Screw (8X)
7. Pull the ‘V’ knuckle strikes from
the ‘V’ knuckle catch of the
steel gables, (Figure 6).
8. Securely fasten the ‘V’ knuckle
strikes to outer gable cover,
using #6 X 5/8” Pan Head
Screws into the pre-drilled
holes, (Figure 7).
9. Securely fasten the Z-brackets
to outer gable cover, using #10
X 11/16” Oval Head Screws into
the pre-drilled holes, (Figure 7).
10. Follow Steps 8 to 9 to install
the hardware of the inner gable
covers.
Continued on the next page >>
FEBRUARY 2020
norris 8

Norris boardroom table – 1 Surface
Figure 8
Figure 9
Tools & Hardware Needed
8540-1280
Drill Allen Key
1/4
-
20 X 35MM
JCB BOLT (8X)
11. Angle the end gable at 30
degrees; Insert the Z brackets
into the slots of the steel gable
and push the gable cover
gently, (Figure 8).
Repeat this procedure for each
gable cover required.
12. Attach the bridge cover, using
1/4-20 X 35mm JCB bolts,
(Figure 9).
FEBRUARY 2020
norris 9

Norris boardroom table – 2 Surfaces
Figure 1
Tools & Hardware Needed
8540-1282
Box Wrench 3/8-16" X 1-1/2"
Hex Bolt (12X)
The procedure below is for Boat,
Straight, Super Ellipse and Video
boardroom tables.
1. Assemble the table base, using
3/8-16” X 1-1/2” Hex Bolt,
(Figure 1).
2. Attach bolts from the thru
holes on the inside of bridge to
the threaded holes on the
plinth.
3. Attach bolts from the thru
holes on outside of the end
gable to the threaded holes on
the bridge.
Note: The steel gables for Video
boardroom tables have two
different sizes. The wide one is for
the wider side of the surface.
Continued on the next page >>
FEBRUARY 2020
norris 10

Norris boardroom table – 2 Surfaces
Figure 2
Figure 3
Tools & Hardware Needed
8540-0789_SCREW MENDPLATE-BLK 8540-0770_Dowel
Drill
Box Wrench
Robertson # 2 #10 X 1" Pan Head
Screw (8X)
Top Bolt (4X) Mending Plate (2X) Wooden Dowel (2X)
4. Place the 2 surfaces on top of
table base and attach them
together by inserting wooden
dowels, (Figure 2).
5. Place the top bolt into the
groove. Tighten the bolt using
a box wrench, (Figure 3).
6. Attach the mending plates,
using #10 X 1” Pan Head
Screws, (Figure 3).
Continued on the next page >>
FEBRUARY 2020
norris 11

Norris boardroom table – 2 Surfaces
Figure 4
Figure 5
Tools & Hardware Needed
8540-0789_SCREW
Drill Robertson # 2 #10 X 1" Pan Head
Screw
7. Position the table base using
the pre-drilled positioning holes
and attach it to table top using
#10 X 1” Oval Head Screws,
(Figure 4).
8. Securely fasten the table base,
using #10 X 1” Pan Head
Screws, (Figure 5).
Continued on the next page >>
FEBRUARY 2020
norris 12

Norris boardroom table – 2 Surfaces
Figure 6
Figure 7
Tools & Hardware Needed
9. Set the power grommets into the
hole of the table top and lay the
electrical wires and
communication cables in the
bridge and end gables, (Figure 6).
10. Please refer to pages 8-9. Follow
Steps 7 to 12 to install the gable
and bridge covers.
11. Insert the plinth gable cover by
angling it at 30 degrees; place the
hooks into the slots and release it
down gently, (Figure 7).
Repeat this to install the other
plinth gable cover.
FEBRUARY 2020
norris 13

Norris boardroom table – 3 Surfaces
Figure 1
Tools & Hardware Needed
8540-1282
Drill
Rubber Mallet
Box Wrench
Robertson # 2 3/8-16" X 1-1/2"
Hex Bolt
8540-0789_SCREW MENDPLATE-BLK 8540-0770_Dowel
#10 X 1" Pan Head
Screw
Top Bolt Mending Plate Wooden Dowel
Note: The procedure below is for
Boat, Straight, and Super Ellipse
boardroom tables.
1. Please refer to page 10.
Follow Steps 1 - 3 to install the
table base.
2. Place the three surfaces on top
of table base and attach them
together by inserting wooden
dowels, (Figure 1).
3. Please refer to pages 11-13.
Follow Steps 5 - 9 to connect
the surfaces, table base, covers
and set the power grommets.
FEBRUARY 2020
norris 14

tayco.com
0220