Ergotron ZAH25CG/CG4 User manual

1 of 4
300-5418-00 rev. R • 10/16
Zido Adjustable, NO LIP Part#
Adjustable, Heavy Load, 25" w ZAH25CG/CG4
Adjustable, Light Load, 22" w ZAL22CG/CG4
Adjustable, Light Load, 25" w ZAL25CG/CG4
Built with Anthro-DNA™
For the latest User Installation Guide please visit: www.ergotron.com
ASSEMBLY INSTRUCTIONS
Zido® Adjustable-Height Cart

2 of 4
300-5418-00 rev. R • 10/16
09
10
11
01
02
03
04
06
05
07
08
Product Quantity Part Number
01 Cap Shelf 1
For small cart, no lip 101-1025-06-50
For small cart, with lip 101-1072-03-50
For large cart, no lip 101-1026-06-50
For large cart, with lip 101-1073-03-50
02 Cap Shelf Bracket 1 225-2620-51
03 Base
For Small Cart 1 250-5064-52
For Large Cart 1 250-5065-52
04 Column
For Light Load Cart 1 835-5290-00
For Heavy Load Cart 1 835-5291-00
05 4" Non-locking Caster 2 150-5010-03
06 4" Locking Caster 2 150-5011-03
07 Release Lever and Paddle 1 835-5393-00
08 Lock Nut 4 325-5263-00
09 1" Cap Screws 4 325-5537-00
10 3/4" Flat-head Patch Screws 2 325-5466-00
11 3/4" Wood Screws 8 325-5575-000
12 3/16" Hex Key (not shown) 1 375-5028-00
13 5/32" Hex Driver (not shown) 1 375-5000-00
WELCOME
Thank you for purchasing this
Zido Height-adjustable cart!
If you have any questions or if we
can help you in any way, please
contact us at 800.325.3841.
PARTS LIST
Before beginning assembly of your Zido Height-adjust-
able Cart, please review the parts list to verify that your
shipment is complete.

3 of 4
300-5418-00 rev. R • 10/16
3/4" Flat Hd Screw
325-5466-00
STEP 1A
Connect the Base with the Tube
Holding the column from the center (don't push
from the top) slide the tube into the base so that
the tube goes all the way to the bottom of the
base.
Align the upper hole on the base with a threaded
hole in the column. (For the large cart, you'll
use the top hole; for the small cart, you'll use the
second hole.) Loosely attach the column to the
base with two 3/4" Flat-head Screw.
STEP 1b
Insert the Casters
Place Zido on its side. Add the locking
casters (the ones with the brakes) to the
front of the base assembly. Add the non-
locking casters to the back of the base
assembly.
ASSEMBLY SEQUENCE
Plan out the assembly sequence to make your installation easier.
1. Pre-drill the top for accessories (Mouse Holder, Side Bin, Gel Cup/Probe Holder, Extension Tube).
2. Assemble the cart.
3. Base Storage Shelf.
4. Drawer, Keyboard Caddy, Standard Handle.
5. Additional Shelves, Equipment Shelves, Metal Bin.
6. Cable Bin, Glove Box Holder.
7. Mouse Holder, Side Bin, Gel Cup & Probe Holder, Extension Tube.
8. 8" Handle, Flat Panel Mounts.

4 of 4
300-5418-00 rev. R • 10/16
© 2016 Ergotron, Inc. All rights reserved.
All trademarks are the property of their respective companies. Anthro is a registered trademark and brand of Ergotron Inc.
Anthro-DNA is a trademark of Ergotron Inc.
1” Button-head Screw
325-5537-00
3/4" Button Hd PB Screw
325-5575-00
Lock Nut
325-5263-00
1" Cap Screws
Lock Nuts
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty
STEP 2
Install the Lever and the Top Plate
Align the lever with the top of the trunk
assembly as shown.
Locate the bracket. The bottom of the bracket
is at and has no sticker. The top of the bracket
has a sticker that says "TOP" and has bumps with
threads inside. The bumps on the top of the
bracket will nest inside the holes on the cap shelf.
Align the cap shelf bracket with the trunk assembly so the bracket's tabs
are at the back and the "TOP" label is on top.
Using the 3/16 hex key, insert four 1" Socket-head Cap screws through the
holes on the top of the Top Plate and capture with four lock nuts inserted
in to the holes in the top of the columns.
Pull up on the lever to move the column up and down. Repeat a few
times to make sure the column moves smoothly. If the lever was installed
upside down, the column won’t move. If that happens, remove the top
plate, invert the lever, and try it again.
CONGRATULATIONS!
YOUR ZIDO ADJUSTABLE CART ASSEMBLY IS COMPLETE!
STEP 3
Install the Cap Shelf
Align the indentations on the bottom of the cap shelf with the screw
heads and bumps on the top of the top plate.
Secure the cap shelf to the cart with eight 3/4" wood screws.
Tighten the 3/4" at-head screws that connect the column to the base.
Pull the paddle up and move the column up and down a few times to
loosen the mechanism. Be sure to operate the column from the back of
the cart so you have plenty of leverage.