Taylor SampleSizer User manual

Timesaving Testing Tools from Taylor
SampleSizer 10/25 mL (#6190) AND
SampleSizer 44 mL (#6191)
Many Taylor drop tests are done with a 25 mL or 10 mL
water sample in either the #9198 sample tube or a 2000
Series™comparator block. A 44 mL sample is used for the
pH color comparison test in the 2000 Series block. Using
these new tools, you won’t need to ick off the excess water
to get the meniscus to rest precisely on the ll line. Simply
lower the appropriate SampleSizer® into the test vial lled
with the water to be tested. It will displace exactly the right
amount to leave the correct volume to perform the test! The
SampleSizer is removed once the extra water is splashed out.
Clean and dry it before storing or using it for another test.
These tools are made from machined aluminum anodized
for longer life.
SpeedStir (#9265)
The SpeedStir®makes quick work of drop tests performed
in Taylor’s #9198 sample tube. (Note: Any 10 or 25 mL
test performed in a 2000 Series comparator block also can
be done in the #9198 sample tube.) This palmsize, portable
magnetic stirrer will thoroughly incorporate each addition
of reagent in a fraction of a second. No more manual swirling!
Place the water sample on the mixing platform then gently
drop in the Teon®-coated stir bar. Use the pad to turn
the unit on in well-lit conditions. Use the pad to start the
stirrer when ambient light is poor — six LEDs below the
mixing platform will light up to make color changes in the
test sample easy to see. Press the same pad to stop the
stirring action, or the unit will turn itself off after ve minutes.
The SpeedStir runs on four AA alkaline batteries at 600 rpm.
Made of high-impact polystyrene, it is water-resistant (you
can spill water on it, but you should not submerge it).
SampleSizer #6190
1” w x 43/4” h
Available singly or
in a multipack of 12
▲
SpeedStir
45/8” l x 13/4” w x 15/8” h
(Shown with #9198 sample tube
supplied in #9265 Start-up Pack)
▲
SampleSizer #6191
7/16” w x 43/4” h
Available singly or
in a multipack of 12
▲

DATA SUMMARY
SampleSizer 10/25 mL SampleSizer 44 mL SpeedStir
Taylor part number #6190 (single)
#6190-12 (12-pack)
#6191 (single)
#6191-12 (12-pack)
#9265
use with #9198 sample tube or new
models of 2000 Series
comparator blocks with
flanges (#9056, #9057,
#9058)
new models of 2000 Series
comparator blocks with
flanges (#9056, #9057,
#9058) and labs K-0200
and K-0206
#9198 sample tube
Taylor replacement part
numbers
NA NA magnetic stirrer (only) #6100
1" magnetic stir bar #6101
sample tube #9198
4 AA alkaline batteries #6105
dimensions 1" dia. x 4 3/4" h 7/16" dia. x 4 3/4" h 4 5/8" l x 1 3/4" w x 1 5/8" h
weight 4.1 oz. 0.9 oz. 7.5 oz. (with batteries)
material anodized machined
aluminum
anodized machined
aluminum
high-impact polystyrene
power NA NA 4 AA alkaline batteries
(approx. 300 tests with light on;
400 tests with light off)
operating temperature range NA NA 36°–120°F; 2°–49°C
revolutions per minute NA NA 600 after 2 seconds
illumination NA NA 6 LEDs
seal submersible
(wipe dry after use)
submersible
(wipe dry after use)
water-resistant: do not
submerge (wipe dry after use)
instructions for use on product packaging on product packaging on product packaging
1. Rinse and fill #9198 sample tube with water
to be tested in excess of desired volume.
4. …all excess water will be displaced.
2. Orient SampleSizer for desired test volume:
an arrow indicates the skinny end goes first
for a 25 mL sample.
5. Tool should touch bottom.
3. Slowly lower the tool into the sample…
6. Carefully remove SampleSizer to avoid
dragging out remaining water. Voilà!
overflow
SampleSizer Demo Using #6190
rev. 111312-ps