Technaxx TX-111 User manual

Technaxx®* User Manual
WiFi Rear Camera System TX-111
Suitable for most of cars (& vans, SUVs, minibuses, caravans, etc.)
as assistance for reverse parking.
This system should be an aid and should NOT replace the need to drive
carefully.
NOTE: the Smartphone in the car may only be used if it is firmly fixed in
a holder.
Under no circumstances will the manufacturer or supplier accept any
responsibility or can held liable for any direct or indirect, incidental or
consequential damage, or for injuries resulting from installing or use of
this system.
The manufacturer Technaxx Deutschland GmbH & Co.KG hereby declares
that this device, to which this user manual belongs, complies with the
essential requirements of the standards referred to the Directive RED
2014/53/EU. The Declaration of Conformity you find here:
www.technaxx.de/ (in bar at the bottom “Konformitätserklärung”). Before
using the device the first time, read the user manual carefully.
Keep this user manual for future reference or product sharing carefully. Do
the same with the original accessories for this product. In case of warranty,
please contact the dealer or the store where you bought this product.
Warranty 2 years
Features
Inconspicuous reversing camera in license plate holder
Suitable for most vehicles as assistance for reverse parking
Video stream over WiFi on Smartphone via APP (New Sight)
Wireless video transmission up to ~10m
IR LED for clear night vision ~4m
Adjustable camera alignements & 110° viewing angle
IP67 camera protection class (dustproof & protection against
temporary immersion)
License plate holder suitable for single-line EC registration
(52x11cm)
Complete installation set
More safety in reverse driving

Technical specifications
License plate holder with camera
Image sensor / Resolution CMOS / 640x480 pixel
Viewing angle 110°
Min. illumination 0.5Lux / automatic white balance
IR night vision distance ~4m
Power supply Connection via WiFi transmitter
Max. current 210mA (incl. transmitter)
Protection class IP67
Weight / Dimensions 264g / (L) 52.8 x (W) 4.0 x (H) 13.7cm
WiFi Transmitter
Modulation (CCK,DQPSK,DBPSK),OFDM(BPSK,
QPSK,16QAM,64QAM)
Protocol IEEE802.11b/g/n
Encoding WPA2
Transmission frequency 2.4GHz
Max. radiated output power 10mW
Weight / Dimensions 72g / (L) 9.5 x (W) 4.0 x (H) 1.4cm
Input voltage DC 12V
Transmission distance ~10m open space (no interferences)
Operating temperature –10°Cup to +50°C
APP name / version New Sight / iOS version 7.0 and higher and
Android version 4.4 and higher
Weight / Dimensions 65g / (L) 9.0 x (W) 3.5 x (H) 1.2cm
Packing
Contents
License plate holder with camera, WiFi transmitter
with power connection for the camera, Mounting
material, User Manual
Hints for Environment Protection: Packages materials are
raw materials and can be recycled. Do not disposal old
devices or batteries into the domestic waste. Cleaning:
Protect the device from contamination and pollution (use a
clean drapery). Avoid using rough, coarse-grained materials or
solvents/aggressive cleaner. Wipe the cleaned device
accurately. Distributor: Technaxx Deutschland GmbH &
Co.KG, Kruppstr. 105, 60388 Frankfurt a.M., Germany

Product overview
The rear view camera sends a video signal from the camera via
WiFi to the smartphone. In case another Bluetooth handsfree
device is installed in your vehicle, it works in the same frequency
range as the camera. If that handsfree device is activated, it may
cause disturbances. Therefore we recommend to deactivate that
other Bluetooth handsfree device while using the reversing system.
License plate holder with camera
1 Infrared-LED 3 Holder
2 Camera 4 Connection cable
WiFi Transmitter
1 Connection cable to the
electrical system 2 Connection cable to camera
WiFi status LED on the WiFi transmitter box:
RED: WiFi is being set up
GREEN: WiFi is ready for connection

Commissioning
Check the functionality of the components before installation (a
installed product is excluded from the return). Preparing and
installing the license plate holder and the transmitter unit.
NOTE: You may need a voltmeter to measure the polarity of the
electrical system.
Break the two locks carefully out of the holder.
Remove the transport locks carefully. Use a sharp knife or a
tong.
 Attach the license plate holder to the vehicle instead of your
previous license plate holder.
 Insert the camera cable into the trunk compartment and
connect it to the transmitter unit.
 Attach the transmitter unit steady and firm in the trunk
compartment.
 Connect the black connection cable of the WiFi
transmitter to the negative pole of the 12V electrical system (on
board-voltage).

 Connect the red connection cable of the WiFi
transmitter to the positive pole of the 12V electrical system (on
board-voltage). You can use any 12V voltage that is switched on or
off with the ignition or the light (rear light). A connection with 12V
continuous plus is not recommended because of the power
consumption. It is also not recommended to connect to the
reversing light as the WiFi transmitter will take about 10 seconds to
establish a connection.
Using the cable clamps
The pictures explains how to use the supplied cable clamps.
1. Put the cable from
the car you want to
connect the WiFi
transmitter with into
the clamp.
2. Insert the 2nd
cable (red or black
cable of the WiFi
transmitter).
3. Close the clamp.
Insert the license plate in the holder
The following drawings show in sequence the insertion of the
license plate.
1. Step
Slide the license plate into the upper
opening.
 Press the number plate towards
the holder.

2. Step
 Slide the license plate down
until it stops.
3. Step
 Insert the locks from above
into the holder.
(You carefully broke them out of the
holder in the first step.)
 Set the camera at an angle where you have a good
view to the rear, depending on the height of the license plate holder
from the ground.
The displayed lines on the Smartphone give you an indication of the
distance.
Definitely control the distance with a folding ruler.
Explanations for the installation of the Smartphone APP can be
found on the following pages.
 Then tighten the screws on both sides of the camera.

Download & install the APP
For the TX-111 you get for Apple iOS (from 7.0) and Android (from
4.4) a suitable APP.
iOS: Download and install the APP
Open the APP-Store or Scan the QR-
code.
In the search field enter New Sight.
Select New Sight under the search
results and confirm with Install.
After the app is installed, you will see a
corresponding icon .
Setting up the WiFi connection:
Go to Settings of your Smartphone.
Open WiFi.
Select WIFICAMERA as WiFi
connection.
At initial startup, enter the following
dialog as Password 88888888 (8x8).
The connection is made.
 Open the APP New Sight.

Android: Download and install the APP
Open the Playstore or Scan the QR-
code.
In the search field, enter New Sight.
Select New Sight under the search
results and confirm with Install.
After the app is installed, you will see
a corresponding icon on the screen.
Setting up the WiFi connection:
Go to Settings. open WiFi.
In the WiFi list, select WIFICAMERA.
At initial startup enter the password
88888888 (8x8).
The connection is made.
 Open the App New Sight.

Start/Open the APP New Sight
Take a snapshot of the current live view
List of taken and saved pictures on your Smartphone.
Take a video of the current live view.
List of taken and saved videos on your Smartphone.
Horizontal reflection (mirror) of the live view
Customize the WiFi name and WiFi password of the WiFi
transmitter. It is suggested to change the name and the
password after the first use. After changing WiFi name
and password you need to reconnect your phone to the
new WiFi. Enter the new given password.

Tips, Note & Attention
A brief tap on the display will hide the menu.
The displayed lines are intended only as an aid to estimating the
distance. To get a feel for it, you should do a driving exercise.
When transferring the images, there is a systemic delay. This
delay is in the range of one-half to one second. They should take
this time into consideration when driving backwards.
Problem and solution
You will only get a gray picture, even though the LED on the
WiFi transmitter box is green.
 In this case, you should reset the WiFi transmitter box. Press
with a pen into the marked RESET button on the WiFi transmitter.
1 Reset 2 WiFi Status
RED: WiFi is being set up
GREEN: WiFi is ready for connection
 Then disconnect the power supply and restore the
connection after approx. 20 seconds. Check if the WLAN
connection is available again.
NOTE: In some cases it may also be necessary to uninstall and
reinstall the App New Sight.
Safety regulations
The reversing system is an aid and does not relieve the driver of his
duty of care in road traffic according to STVO. Please read these
instructions carefully before first use.

General information:
Never place the device on an unstable surface. Dropping may
damage the device. The device is not in the hands of children. It is not
a toy. Also observe the safety instructions and the operating
instructions of the other devices to which the device is connected. In
commercial facilities, the accident prevention regulations of the
Association of Professional Associations for Electrical Installations and
Equipment must be observed. In schools, training centers, hobby or
self-help workshops, the operation of electronic products is to be
monitored responsibly by trained personnel. The seller assumes no
responsibility for damage that occurs during the use of the device, as
well as for complaints by third parties.
Environmental conditions:
Avoid heavy mechanical stress on the device. Protect it from vibration,
hard knocks, do not drop it or shake it. Do not expose the device to
high temperatures (over 50°C) and strong temperature fluctuations.
Protect it from direct solar radiation and proximity to radiators. IP67
camera protection class (dustproof & protection against temporary
immersion). The monitor and the transmitter may only be operated
indoors. It cannot be completely ruled out that some paints, plastics or
other care products attack the material of the housing or accessories.
Disorders: If an object or liquid gets into the device, have the device
checked by an authorized technician before continuing to use it. We
recommend that you contact our service center.
Packing material: Keep children away from packaging material. There
is danger of suffocation.
Cleaning and care: Always store the device in a clean, dry place when
not in use. Use a dry, soft cloth to clean the exterior surfaces.
Interference by wireless transmission: The device operates at a
frequency of 2468 MHz. This frequency can also be used by other
devices that transmit video wireless. It can thus come in individual cases
to disturbances.
Service phone No. for technical support: 01805 012643 (14 cent/minute from
German fixed-line and 42 cent/minute from mobile networks).
Free Email: sup[email protected]
Enjoy your product * Share your experience and opinion on one of the
well-known internet portals.