aidapt VG832AA Programming manual

VG832AA
Overbed Table
Usage and Maintenance Instructions
EN

INTRODUCTION
Thank you for purchasing the Overbed Table from Aidapt.
BEFORE USE
INTENDED USE
CONTENTS
ASSEMBLY INSTRUCTIONS
• Carefully remove all packaging. Avoid using any knives or other sharp
instruments as this may damage the surface of the product.
• Check the product for any visible damage. If you see any damage or
suspect a fault, do not use your product, but contact your supplier for
support.
• The overbed table is both height and angle adjustable.
• Wooden Finished Table-Top (a)
• Chrome L-Shaped Leg Brackets x2 (b)
• L Shaped Tube with Thumbwheel x2 (c)
• C Shaped Tube with Thumbwheels(d)
1. Carefully unpack your Overbed Table and examine all parts for any
damaged or, loose tments. Should you nd any fault, please return your
table to your supplier for exchange.
1
Usage and Maintenance Instructions
(a)
(c)
(b)
(d)

2. After inspection, place the wooden nished table-top face (a) down onto a soft
surface to avoid scratches.
3. If required, insert the chrome leg brackets (b) into clamps on the wooden base
(a). (g. 1)
4. Depress click release pins. (g. 2-3)
5. Attach C shaped tube (d) to L shaped tube (c) using the thumbwheels. (g 4)
2
Usage and Maintenance Instructions
(g. 1)
(g. 2)
(g. 4)
(g. 3)

6. Slide L shaped tube (c) over chrome L-Shaped brackets (b) to desired height.
Ensure they are both the same height. (g. 5)
7. Tighten all thumbwheels by turning clockwise before use. (g. 6)
3
Usage and Maintenance Instructions
(g. 5)
(g. 6)

IMPORTANT INFORMATION
The information given in this instruction booklet must not be taken as forming
part of or establishing any contractual or other commitment by Aidapt Bathrooms
Limited, Aidapt (Wales) Ltd or its agents or its subsidiaries and no warranty or
representation concerning the information is given.
Please exercise common sense and do not take any unnecessary risks when using
this product; as the user you must accept liability for safety when using the product.
Please do not hesitate to contact the person who issued this product to you or the
manufacturer (detailed below) if you have any queries concerning the assembly/
use of your product.
Aidapt Bathrooms Ltd, Lancots Lane, Sutton Oak, St Helens, WA9 3EX
Telephone: [phone] Fax: [phone]
Web: www.aidapt.com
Email: [email protected]
CLEANING
CARE & MAINTENANCE
Clean your Overbed Table using a mild detergent with a slightly damp, soft cloth
only. Only use a mild detergent or disinfectant; never use an abrasive cleaner. Using
abrasive cleaning materials, very hot water or scrubbing the table top may result in
damage.
Please make a safety check of the product at regular intervals or if you have any
concerns.
OPERATION INSTRUCTIONS
• To adjust the height and/or angle of the table, rst loosen the two short
thumbwheels by turning them anticlockwise. Adjust the table to suit and
secure by turning thumbwheels clockwise.
NB. Ensure thumbwheels are adequately tightened before use.
NB. Ensure there is nothing on the table when adjusting.
• The table is not load bearing and should not be used to support objects
over 15kgs (33lbs).
• Do not allow people to lean on the table.
REISSUE
If you reissue or are about to reissue this product, please thoroughly check all
components for their safety.
If in any doubt, please do not issue or use, but immediately contact your
supplier for service support.
Usage and Maintenance Instructions