Noble House Home Furnishings LOVESEAT User manual

Assembly Instructions
Caution: You must read this before you proceed
Please look in the Left Leg for hardware packs
LOVESEAT
Noble House Home Furnishings LLC 1 of 8
CAUTION: This Loveseat is NOT a TOY.
Keep your child / children at bay during the assembly process.
For turning the Loveseat and to prevent damage to the Loveseat, 02
persons may be needed to execute this action

Label Picture Description QTY
A Right Leg 1
B Left Leg 1
C Seat Panel 1
D Support bar 1
E Back Cushion 2
F Seat Cushion 1
Parts List
Noble House Home Furnishings LLC 2 of 8

Label Picture Description QTY
①
Bolt
(M6x20 mm) 5
②
Bolt
(M6x40 mm) 3
③
Bolt
(M6x60 mm) 3
④Washer
(M6/14x1mm) 5
⑤Allen Key 1
Hardware
Assembly Preparation
Before Beginning Assembly:
Noble House Home Furnishings LLC 3 of 8

Assembly Steps
Overview
This Loveseat has multiple parts and may require up to some 30 minutes to assemble. To
give you an overview of the Loveseat, the above picture is to help you put the various parts
into perspective.
Please read through the instructions here below to familiarise the parts and steps before
assembly.
Step 1
Unpack and place all parts on a clean, non-marring surface.
FRONT FACING
Right Leg
(A)
Seat Panel
(C)
Left Leg
(B)
Seat Cushion
(F)
Back Cushion
(E)
Support bar
(D)
Noble House Home Furnishings LLC 4 of 8

Place the Right Leg (A) facedown onto a clean, non-marring surface.
Position Support Bar (D) to Right Leg (A) as shown in the above picture, then attach Support
Bar (D) to Right Leg (A) by using Bolt (②) with Allen Key (⑤).
Do not fully tighten the Bolts.
Step 3
With assistance from your adult partner, position Seat Panel (C) to Right Leg (A) as shown in
the above picture.
Secure Seat Panel(C) to Right Leg (A) by using Bolts (①) and Washers (④) with Allen Key
(
⑤
).
Do not fully tighten the Bolts.
Step 2
5
2
D
A
C
A
D
5
1
4
Noble House Home Furnishings LLC 5 of 8

Step 4
4.1. Attach Left Leg (B) to Support Bar (D) by using Bolt (
②
) with Allen Key (
⑤
).
4.2. Secure Left Leg (B) to Seat Panel (C) by using Bolts (
①
) and Washers (
④
) with Allen
Key (
⑤
).
Do not fully tighten the Bolts.
Step 5
With the assistance from your adult partner, stand the assembled parts in step 4 up.
Secure the Right Leg (A) and Left Leg (B) to Seat Panel (C) by using Bolts (③) with Allen
Key (
⑤
).
Do not fully tighten the Bolts.
B
C
D
5
2
4
5
1
A
B
5
3
C
Noble House Home Furnishings LLC 6 of 8

Step 7
Place the Seat Cushion (F) and the Back Cushions (E) onto the Loveseat as shown above.
Inspect it and make sure all parts are adequately connected.
Ensure all bolts are fully locked into position and secured.
Your Loveseat is ready to be used.
This Loveseat can only be used on a flat, level surface.
Step 6
Inspect the Loveseat and make sure all parts are adequately connected.
Carefully sit onto the Loveseat. This pressure will help align all parts at all joints.
In a sequential manner, tighten all Bolts at all joints.
Adjust the Levellers until the Loveseat is level with the ground.
To adjust the Levellers, get assistance from an adult partner to lift/lean and hold the
Loveseat while you are working.
Noble House Home Furnishings LLC 7 of 8
Adjust high for balance Adjust low for balance
Adjust Pre-installed

Noble House Home Furnishings LLC 8 of 8