Techni Mobili RTA-1462 User manual

MODEL RTA-1462
ASSEMBLY INSTRUCTIONS
D06 080906
WARNING:
DO NOT EXPOSE THE SURFACES TO DIRECT SUN LIGHT. EXPOSURE WILL DAMAGE
IT SURFACES, WHICH WILL NOT BE COVERED UNDER THE PRODUCT'S WARRANTY.
Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Please save this manual for future reference

45.25”
21.5”
5.8”
15.7”
30”
3”
44.85”
13.8”
24.8”
1.45”
1.45”
13.7”
13.2”
13.2”
TOP WEIGHT LIMIT:50Lbs
SMALL DRAWER WEIGHT LIMIT:10Lbs
BIG DRAWER WEIGHT LIMIT:15Lbs
DO NOT exceed this limit.
Please use care and good judgment when placing objects on the product.

341 2
58
9
67
10
13 14
12
15
18
16
17 19 20
21
P. 3
Sliders
PARTS LIST
Supporting tube
RTA-1462
11
22
x2 x2
Central panel Left back panel Right back panel Hinge s
Main structure s Left pane l Right panel
x2
Central horizontal panel Auxiliary panel Main panel Front panel
Drawer left panel Small drawer back panel Large drawer back panel
Drawer right panel Bottom panel Small drawer bottom
panel
Large drawer bottom
panel
Drawers bottom
support panel Studs x4
x1 x1
x1 x1
x1
x1
x1
x1
x1
x1
x2
x1
x1
x2 x1
x1
x1
Right
Left
x2SETS

RTA-1462 P. 4
A
B
D
C
E
24
17
17
12
PART QTY . ITEM PART QTY . ITEM
4X12 MM
F
8
I
3.8X35 MM
6X12 MM
J
K
9
12
L
M
3.8X40 MM
G
4 6X30 MM
H
6X15 MM
4
4
24
1
1
3.5X12MM
WOODEN PIN
6x40 MM CAM BOLT
6x40 MM CAM LOCK WOODEN PIN
ALLEN WRENCH
CORRECT
If the panel already comes with the cam lock inserted,make sure is alligned
1.Screw the bolt into the
corresponding panel
2.In the other panel,insert and align the cam
lock,Join the panels
3.Turn the cam lock
Cam lock
Cam bolt
SCREWS
1
MISALIGNED:
TURN CAM LOCK
TO POINT TOWARDS
THE HOLE
.
.

RTA-1462 P. 6
12
34
STEPS
B
12
13
17
L
L
Left
14
14
Right
13
17
15
H
H
H
17
16
13
21
19
20
H
H
H
Attention:Do not tighten the screws until all of them are in right positions
WARNING:HOLES ON PANELS MAY BE HIDDEN UNDERNEATH PVC LAMINATE!!!
J
L
B J
(H) H
H

RTA-1462 P. 7
56
78
STEPS
12
19
20 C
3
4
L
L
Left
14
14
Right
4
3
B
B
Instructions on page 4
CL
LB

RTA-1462 P. 8
910
11 12
STEPS
L
L
14
Right
Left
14
5
3
4
9C
6
7
8
D
Instructions on page 4
8
D
Right
Left
A
A
L
C
DD

RTA-1462 P. 9
13 14
15 16
STEPS
6C
A
C
B11
B
C
11
5
Instructions on page 4
Instructions on page 4
Instructions on page 4
7
doing this step.
C C
B
C

RTA-1462 P. 10
17
18 19
STEPS
18
I
A
11
4 PCS
22 18
1
F
6X30 MM
4 PCS
1
These holes are for steps 19&20
I
F

RTA-1462 P. 11
20
21
STEPS
10
D
E
6X12 MM
8 PCS G
6X15 MM
4 PCS
2
2
Carefully turn the table upright. Assemble
the auxiliary panel (10) using screws (D) as
shown. After installing the hinges, they might
need fine-tuning for proper alignment and
smooth closing. If adjust is necessary,
loosen or tighten the 2 adjusting screws as
indicated below.
This screw can adjust the
No.10 panel back and forth.
This screw can adjust the
No.10 panel up and down.
E
G

RTA-1462 P. 12
22
23
STEPS