Techni Mobili RTA-1462 User manual

ÓÑÜÛÔ ÎÌßóïìêî
ßÍÍÛÓÞÔÇ ×ÒÍÌÎËÝÌ×ÑÒ
ÓÑÜÛÔÎÌßóïìêî
Üðê ðèðçð ê
ÉßÎÒ×ÒÙæ
ÜÑ ÒÑÌ ÛÈÐÑÍÛ ÌØÛ ÍËÎÚßÝÛÍ ÌÑ Ü×ÎÛÝÌ ÍËÒ Ô×ÙØÌò ÛÈÐÑÍËÎÛ É×ÔÔ ÜßÓßÙÛ
×Ì ÍËÎÚßÝÛÍô ÉØ×ÝØ É×ÔÔ ÒÑÌ ÞÛ ÝÑÊÛÎÛÜ ËÒÜÛÎ ÌØÛ ÐÎÑÜËÝÌùÍ ÉßÎÎßÒÌÇò
̸¿²µ- º±® °«®½¸¿-·²¹ ±²» ±º ±«® °®±¼«½¬-ò
д»¿-» ®»¿¼ ½¿®»º«´´§ ¬¸» ¿--»³¾´§ ·²-¬®«½¬·±²- ¾»º±®» ¬¸» ·²-¬¿´´¿¬·±²ò
д»¿-» -¿ª» ¬¸·- ³¿²«¿´ º±® º«¬«®» ®»º»®»²½»

45.25”
21.5”
5.8”
15.7”
30”
3”
44.85”
13.8”
24.8”
1.45”
1.45”
13.7”
13.2”
13.2”
TOP WEIGHT LIMIT:50Lbs
SMALL DRAWER WEIGHT LIMIT:10Lbs
BIG DRAWER WEIGHT LIMIT:15Lbs
DO NOT exceed this limit.
Please use care and good judgment when placing objects on the product.

3 41 2
5 8
9
6 7
10
13 14
12
15
18
16
17 19 20
21
P. 3
Sliders
PARTS LIST
Supporting tube
RTA-1462
11
22
x2 x2
Central panel Left back panel Right back panel Hinge s
Main structure s Left p ane l Right panel
x2
Central horizontal panel Auxiliary panel Main panel Front panel
Drawer left panel Small drawer back panel Large drawer back panel
Drawer right panel Bottom panel Small drawer bottom
panel
Large drawer bottom
panel
Drawers bottom
support panel
Studs x4
x1 x1
x1 x1x1
x1
x1
x1
x1
x1
x2
x1
x1
x2 x1
x1
x1
Right
Left
x2SETS
NOTE:CORRECT USE OF B WITH A AND M

RTA-1462 P. 4
A
B
D
C
E
24
2
17
17
12
PART QTY . ITEM PART QTY . ITEM
4X12 MM
F8
I3.8X35 MM
6X12 MM
J
K
9
12
L
M
3.8X40 MM
G4 6X30 MM
H6X15 MM
4
4
24
1
1
3.5X12MM
WOODEN PIN
GLUE
6x40 MM CAM BOLT
6x40 MM CAM LOCK
WOODEN PIN
ALLEN WRENCH
CORRECT
If the panel already comes with the cam lock inserted,make sure is alligned
ï.Screw the bolt into the
corresponding panel
î.In the other panel,insert and align the cam
lock,Join the panels
í.Turn the cam lock
Cam lock
Cam bolt
SCREWS
N1
MISALIGNED:
TURN CAM LOCK
TO POINT TOWARDS
THE HOLE
ò
ò

ïìêî
5

RTA-1462 P. 6
12
34
STEPS
C
12
13
17
M
M
Left
14
14
Right
13
17
15
I
I
I
17
16
13
21
19
20
I
I
I
Attention:Do not tighten the screws until all of them are in right positions
WARNING:HOLES ON PANELS MAY BE HIDDEN UNDERNEATH PVC LAMINATE!!!
K
M

RTA-1462 P. 7
56
78
STEPS
12
19
20 D
3
4
M
M
Left
14
14
Right
4
3
C
C
Instructions on page 4

RTA-1462 P. 8
910
11 12
STEPS
M
M
14
Right
Left
14
5
3
4
9D
6
7
8
E
Instructions on page 4
8
E
Right
Left
A
A

RTA-1462 P. 9
13 14
15 16
STEPS
6D
A
D
C11
C
D
11
5
Instructions on page 4
Instructions on page 4
Instructions on page 4
7
¼±·²¹ ¬¸·- -¬»°ò

RTA-1462 P. 10
17
18 19
STEPS
18
J
A
11
4 PCS
22 18
1
G
6X30 MM
4 PCS
1
These holes are for steps 19&20

RTA-1462 P. 11
20
21
STEPS
10
E
F
6X12 MM
8 PCS H
6X15 MM
4 PCS
2
2
Carefully turn the table upright. Assemble
the auxiliary panel (10) using screws (E) as
shown. After installing the hinges, they might
need fine-tuning for proper alignment and
smooth closing. If adjust is necessary,
loosen or tighten the 2 adjusting screws as
indicated below.
This screw can adjust the
No.10 panel back and forth.
This screw can adjust the
No.10 panel up and down.

RTA-1462 P. 12
22
23
STEPS