Techni Mobili RTA-733DL User manual

Thank you for purchasing our product.
MODEL RTA-733DL
ASSEMBLY INSTRUCTIONS
REV.PFT-6378-0222-0
Option A
Option B

•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.
P. 1 RTA-733DL P. 1

P. 2 RTA-733DL P. 2
1
x1
2
x1
3
x1
Left tabletop Corner top Right tabletop
MAIN PARTS LIST
4
x4
5
x1
6
x1
Shelf Adjustable top shelf Left frame
7
x3
Right and center-right frame
10
x1
11
x1
Left-top-front tube Right-top-back tube 12
x1
Right-top-front tube
13
x2
14
x2
Long cross tube Short cross tube 15
x2
Stand
support
8
x1
Center-left frame 9
x1
Left-top-back tube
16
x1
Earphones
hook

MAIN PARTS LAYOUT (FOR REFERENCE):
P. 3 RTA-733DL P. 3
LIST OF HARDWARE, SCREWS AND FITTINGS
PART
QTY ITEM
A8M6x12
B43 M6x30
C7M6x40
D11 M6 Nut cap
E2M6 Screw
knob
PART
QTY ITEM
F230x25mm
Protector
G125x25
Bracket
1M4 Allen
wrench
1Wrench
(Spanner)
1
2
3
6
5
4
9
10
11
12
13
14
15
16
4
4
4
7
7
7
8

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P. 4 RTA-733DL P. 4
❸The replacement parts
service is limited to the
48 contiguous United States.
If you reside in Alaska,
Hawaii, Puerto Rico,
U.S. territories or other
countries, please contact the
supplier from where the unit
was purchased.

ASSEMBLY STEPS
•Assemble one of the shelves 4to the bottom bars on the right frames
7with screws Bfrom underneath.
•Assemble another shelf 4to either set of middle bars on the frames 7
with screws Baccording to your preference, or calculating enough
space if you intend to put your CPU unit on the bottom shelf.
STEP 1
Hardware:
B
M6x30
8
Pcs
P. 5 RTA-733DL P. 5
•Assemble another shelf 4to the frames 7and 8with screws Bfrom
underneath, making sure the frame 7stays on the LEFT and the
frame 8on the RIGHT.
•Assemble the last shelf 4to either set of middle bars on the frames 7
and 8with screws Baccording to your preference, or calculating
enough space if you intend to put your CPU unit on the bottom shelf.
STEP 2
Hardware:
B8
Pcs
The top shelf can
be assemble on
either set of bars.
The top shelf can
be assemble on
either set of bars.
RIGHT
LEFT
4
4
(Front)
(Back)
7
7
M6x30
(Front)
(Back)
4
4
7
8

P. 6 RTA-733DL P. 6
•Assemble the right-top-back tube 11 and the right-top-front tube 12 in
between the frames 7in their corresponding positions with screws C.
•Pay attention to the orientation of the holes on the frames and tubes.
•Join the short cross tubes 14 to each other in the center with screw A
and nut cap D, but leave them loose.
•Attach the cross tubes 14 to the frames 7with screws Band nut caps
D. The caps go on the inside of the unit.
•Tighten all the screws and nut caps.
STEP 3
Hardware:
C4
Pcs
STEP 4
Hardware:
A1
Pc
B4
Pcs
D5
Pcs
M6x40
(Front)
(Back)
(Front)
(Back)
8
7
12
11
(Front)
M6x12
1
M6x30
4
M6
nut cap
5
(Front)
(Back)
14
7
7
B
A
14
D
7
7

P. 7 RTA-733DL P. 7
•With the help of another person, place the corner top 2and the right
tabletop 3over the frame, making sure the holes align.
•Secure the tabletops to the frames 7, 8and the tubes 11 and 12 with
screws Bfrom underneath, but leave the screws loose to allow
flexibility to fix any misalignments.
STEP 5
Hardware:
B12
Pcs
•Assemble the left-top-back tube 9and the left-top-front tube 10 to the
frame 6on their corresponding positions with screws C.
•Assemble the hook 16 to the frame 6with screw A. Please note that
the hook will be located on the inside of the frame but facing towards
the outside.
STEP 6
Hardware:
A1
Pc
C2
Pcs
M6x30
(Front)
(Back)
3
2
8
7
7
11
12
7
M6x12
M6x40
(Back)
(Front)
(Front)
(Back)
10
9
6
16
C
A

P. 8 RTA-733DL P. 8
•With the left tabletop 1flipped upside-down, assemble to it the tubes
6, 9and 10 with screws B, but leave the screws loose to allow
flexibility to fix any misalignments.
•Attach the bracket Gto the tube 9with screw A. Make sure to leave
the bracket facing towards the outside.
STEP 7
Hardware:
A1
Pc
B6
Pcs
G1
Pc
•Assemble the supports 15 to the top shelf 5with screws A.
STEP 8
Hardware:
A
M6x12
4
Pcs
M6x12
M6x30
25x25
Bracket
(Front)
(Back)
9
16
10
A
GB
15
5
15
Make sure to attach the
supports oriented in the
same direction

P. 9 RTA-733DL P. 9
At this point you will have 2 options to finish building your desk:
A. Straight which allows to seat 2 persons. Follow steps 9A, 10A and 11A.
B. As an “L” shape for ample workspace for 1 person. Follow steps 9B, 10B
and 11B.
OPTION A: FOLLOW STEPS 9A, 10A and 11A.
OPTION B: FOLLOW STEPS 9B, 10B and 11B.

P. 1 0 RTA-733DL P. 1 0
With the help of another person, assemble the left tabletop 1to the rest
of the unit using:
•Screw Bgoing through the frame 7and the bracket Gon the tube 9at
the back of the unit, and secure with nut cap D.
•Screw C going through the frame 7and into the tube 10 at the front of
the unit.
STEP 9A
Hardware:
B
M6x30
1
Pc
C
M6x40
1
Pc
DM6
Nut cap
1
Pc
With the help of another person, assemble the left tabletop 1to the rest
of the unit using:
•Screw Bgoing through the frame 7and the bracket Gon the tube 9at
the back of the unit, and secure with nut cap D.
•Screw C going through the tube 12 and into the tube 10 at the front of
the unit.
STEP 9B
Hardware:
B1
Pc
C1
Pc
D1
Pc
(Front)
(Back)
1
8
2
D
B
G
10
8
C
M6x30
M6x40
M6
Nut cap
(Right)
(Left)
(Front)
(Back)
1
D
12
2
B
8
G
C
(Under
tabletop 2)
10
M6x30
M6x40
M6
Nut cap

P. 11 RTA-733DL P. 11
•Join the long cross tubes 13 to each other in the center with screw A
and nut cap D, but leave them loose.
•Attach the cross tubes 13 to the frames 6 and 8 with screws Band nut
caps D. The caps go on the inside of the unit.
•Tighten all the screws and nut caps.
STEP 10A
Hardware:
A1
Pc
B4
Pcs
D5
Pcs
•Join the long cross tubes 13 to each other in the center with screw A
and nut cap D, but leave them loose.
•Attach the cross tubes 13 to the frames 6 and 8 with screws Band nut
caps D. The caps go on the inside of the unit.
•Tighten all the screws and nut caps.
STEP 10B
Hardware:
A1
Pcs
B4
Pcs
D5
Pcs
(Right)
(Left)
(Front)
(Back)
A
B
13
D6
13
8
M6x12
M6x30
M6
Nut cap
(Right)
(Left)
(Front)
(Back)
A
B
13
6
D
13
8
M6x12
M6x30
M6
Nut cap

P. 1 2 RTA-733DL P. 1 2
•Mount the supports 15 to either tabletop 1or 3with the screw knobs
Eand the protector F.
(Front)
(Front)
STEP 11A
Hardware:
E2
Pcs
F2
pcs
•Mount the supports 15 to either tabletop 1or 3with the screw knobs
Eand the protector F.
(Front)
(Front)
STEP 11B
Hardware:
E2
Pcs
F2
pcs
ALL DONE!
Give yourself a nice pat on the back. You did a great job!
15
E
F
M6
Screw
knob
30x25
Protector
ON RIGHT SIDE 3
OR ON LEFT SIDE
1
ON RIGHT SIDE 3
15
E
F1
OR ON
LEFT SIDE
M6
Screw
knob
30x25
Protector

P. 1 3 RTA-733DL P. 1 3
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletops.
•Do not sit on the unit or lean against it.
•Do not allow small children to play under the unit or climb over it.
•Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be lifted by
at least 2 persons when moving in the same or adjacent rooms.
•Before moving the unit, make sure to secure or remove any object that is heavy or might
fall off.
•Lift from the frame, not the tabletops.
•When lifting the unit, use both hands and bend your knees, not your backs.
•When transporting the unit to places far away, protect and secure the unit to avoid damage
in transit. If possible, disassemble it in sections.
•Shall any part of the unit become defective during the warranty period, replacement parts
might be available to you at no charge. Please refer to the last pages on this manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes
liability for damages or consequences due to accidents, incorrect assembly, negligence,
improper use, modifications, or not heeding the above warnings.
CARE, MAINTENANCE AND SAFETY WARNINGS:
WEIGHT LIMITS
88 Lbs.
(40 Kg)
66 Lbs.
(30 Kg)
22 Lbs.
(10 Kg)
88 Lbs.
(40 Kg)
66 Lbs.
(30 Kg)
88 Lbs.
(40 Kg)

RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA
Products or its authorized resellers that this product will be free from defects in its
workmanship and materials, under normal use and service conditions, as described herein.
"Defects" as used in this warranty, is defined as any imperfections that impair the use of the
furniture or product. RTA Products LLC will replace any defective part, at its discretion, and
without charge to the original purchaser other than the freight from the end consumer to RTA
Products.
Replacement parts can only be supplied if parts are available. Items out of production may be
unavailable. This warranty will be effective for the applicable time period beginning the date
of purchase on your original sales receipt. RTA product’s obligation under this warranty is
limited to repairing or replacing products or parts as provided herein. This product has been
designed for and is intended for office and home-office use only. This warranty is Original
Purchaser’s sole remedy for product defects, and this warranty does not extend to any
product, or damage to any product, caused by or attributed to abuse or misuse, products
used for commercial or rental purposes, use modifications of, or attachments to the product,
and products or parts not used, maintained, or extended hereunder is in lieu of any and all
other warranties, express or implied, including without limitations any implied warranty or
merchantability or of fitness for a particular purpose. Please note, all desks made with PVC
Laminate surface should not be exposed to direct sunlight, as it may damage the material.
Damage of this nature is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential
damages. This warranty is limited to merchandise purchased in the Continental United
States, excludes AK, HI and PR. Some States do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights. You may also have other rights that may
vary from state to state.
RTA Products will advise you of the procedure to follow in making warranty claims. The
following are the procedures for warranty claims:
a. Call us Monday –Friday, from 9am-5pm (Eastern Time) at [phone] to explain the
defect and give your name, address and phone number. Please have ready the model
number of our product, date and place of purchase. You can also write to us by e-mail
to [e-mail] and include the same information.
b. If we determine that replacement will remedy the situation, and in order to determine the
extent or the cause of the defect, purchaser will need to send the part in question at
purchaser’s expense. Once we receive the part, we will examine it and determine
whether the claim is valid (or not), and then proceed to send the replacement. We will
ship the replacement at our expense.
P. 1 4 RTA-733DL P. 1 4
TECHNI MOBILI DESK WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: [e-mail]