Techni Mobili RTA-2018 User manual

Thank you for purchasing our product.
MODEL RTA-2018
ASSEMBLY INSTRUCTIONS
REV.032021-2

•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.
P. 1 RTA-2018 P. 1

P. 2 RTA-2018 P. 2
1L
x1
1R
x1
2L
x2
2N
x2
Left structure Right structure Locking caster Non-locking caster
MAIN PARTS LIST
3
x1
Back panel
4
x1
Lower panel 5
x1
Main panel
6
X1
SET
7
x1
Keyboard slider
(SET)
Keyboard panel 8
x1
9
x1
Printer/Monitor
panel
CD holder
10A
x2
10B
x2
Support tube Protection clip 10C
x2
Screw knob

MAIN PARTS LAYOUT (FOR REFERENCE):
P. 3 RTA-2018 P. 3
LIST OF SCREWS AND TOOLS
PART QTY ITEM
A4M6x45
B8M6x30
C6M6x12
D4ST4x12
E4M4x12
1Hex wrench (Spanner)
1Allen wrench
8
10
9
5
7
4
1R
1L
2L
2N

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❸The replacement parts
service is limited to the
continental United States.If
you reside in Hawaii, Puerto
Rico, U.S. Dependencies or
other countries, please
contact the supplier from
where the unit was
purchased.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P. 4 RTA-2018 P. 4

ASSEMBLY STEPS
Use the wrench to install the casters 2to the structures 1L and 1R in the
following order:
☛The locking casters 2L go on the front bottom holes,
☛The non-locking casters 2N go on the back bottom holes.
STEP 1
Screws/Tools:
P. 5 RTA-2018 P. 5
First check and make sure of the correct alignment of the inserts in the
back panel 3, then assemble it to the structures 1L and 1R with screws A.
STEP 2
Screws/Tools:
A
M6x45
4
Pcs
L
N
Locking at front
Non-locking at back
Panel 3 comes with pre-aligned metal inserts on its interior face. If the
screws don’t want to enter in the panel, you will have to use the Allen
wrench to turn and re-align the inserts as shown below.
The middle and
lower bars face
towards the
inside.
If the insert is misaligned,
turn it to the correct direction:
NO X
YES √
Scan QR Code to
view this step

P. 6 RTA-2018 P. 6
Assemble the lower panel
4to the lower bars on the
structures 1L,1R with
screws Bfrom underneath
as shown.
STEP 3
Screws/Tools:
B
M6x30
4
Pcs
Assemble the main panel
5to the top bars of the
structures 1L and 1R
with screws Bfrom
underneath as shown.
STEP 4
Screws/Tools:
B
M6x30
4
Pcs
STEP 5
Screws/Tools:
E
M4x12
4
Pcs
Assemble the keyboard sliders 6 on their respective sides to the middle
bars of the structures 1L and 1R with screws Efrom the inside. The
screws have to go through the sliders’ holes and insert into the holes on
the structures as shown.
The flat side
goes against
the bar
The tabs face down

P. 7 RTA-2018 P. 7
Assemble the keyboard panel 7 to the sliders 6 with screws D from
underneath as shown.
Assemble the CD rack 9 to either structure 1L or 1R with screws C
according to your preference.
STEP 6
Screws/Tools:
D
ST4x12
4
Pcs
STEP 7
Screws/Tools:
C
M6x12
2
Pcs
OR
STEP 8
Screws/Tools:
C
M6x12
4
Pcs
Assemble the support tubes 10A to the monitor/printer panel 8 with
screws C, then insert the protection clips 10B in the support tubes as
shown.

P. 8 RTA-2018 P. 8
Assemble the support tubes 10A to the main panel 5 in the position of
your preference making sure that the protection clips 10B are positioned
in between, then use the screw knobs 10C to secure the tubes as shown.
STEP 9
IMPORTANT:
Place the protection
clips 10B first!
(This view is from the back side)
ALL DONE!
Give yourself a nice pat on the back. You did a
great job!

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop.
•Do not sit on the unit or lean against it.
•Do not allow small children to play under or over the unit, nor use it as a moving
vehicle.
•Keep the unit with the front casters locked.
•Before moving the unit, make sure to unlock the front casters, and secure or remove
any object that might fall off.
•When lifting the unit, use both hands and bend your knees, not your backs.
•When transporting the unit to places far away, lock the front casters and protect and
secure the unit to avoid damage in transit.
•Shall any part of the unit become defective during the warranty period, replacement
parts might be available to you at no charge. Please refer to the last pages on this
manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes
liability for damages or consequences due to accidents, incorrect assembly,
negligence, improper use, modifications, or not heeding the above warnings.
WEIGHT LIMITS
P. 9 RTA-2018 P. 9
30 Lbs.
(13.60 Kg)
100 Lbs.
(45.36 Kg)
22 Lbs.
(9.97 Kg)
30 Lbs.
(13.60 Kg)

RTA Products, LLC warrants to the Original Purchaser who acquired anew product from
RTA Products or its authorized resellers that this product will be free from defects in its
workmanship and materials, under normal use and service conditions, as described
herein."Defects" as used in this warranty, is defined as any imperfections that impair the
use of the furniture or product.RTA Products LLC will replace any defective part, at its
discretion, and without charge to the original purchaser other than the freight from the end
consumer to RTA Products.
Replacement parts can only be supplied if parts are available.Items out of production
may be unavailable.This warranty will be effective for the applicable time period
beginning the date of purchase on your original sales receipt.RTA product’s obligation
under this warranty is limited to repairing or replacing products or parts as provided
herein.This product has been designed for and is intended for office and home-office use
only.This warranty is Original Purchaser’s sole remedy for product defects, and this
warranty does not extend to any product, or damage to any product, caused by or
attributed to abuse or misuse, products used for commercial or rental purposes, use
modifications of, or attachments to the product, and products or parts not used,
maintained, or extended hereunder is in lieu of any and all other warranties, express or
implied, including without limitations any implied warranty or merchantability or of fitness
for aparticular purpose.Please note, all desks made with PVC Laminate surface should
not be exposed to direct sunlight, as it may damage the material.Damage of this nature
is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential
damages.This warranty is limited to merchandise purchased in the Continental United
States.Some States do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.This warranty
gives you specific legal rights.You may also have other rights that may vary from state to
state.
RTA Products will advise you of the procedure to follow in making warranty claims.The
following are the procedures for warranty claims:
a. Call us Monday –Friday, from 9am-5pm (Eastern Time) at [phone] to explain
the defect and give your name, address and phone number.Please have ready the
model number of our product, date and place of purchase.You can also write to us by
e-mail to [e-mail] and include the same information.
b. If we determine that replacement will remedy the situation, and in order to determine
the extent or the cause of the defect, purchaser will need to send the part in question
at purchaser’s expense.Once we receive the part, we will examine it and determine
whether the claim is valid (or not), and then proceed to send the replacement.We will
ship the replacement at our expense.
P. 1 0 RTA-2018 P. 1 0
TECHNI MOBILI WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY
TV Stand/Entertainment Center: 2 YEAR WARRANTY

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: [e-mail]
P. 11 RTA-2018 P. 11