Techni Mobili RTA-3805L User manual

Thank you for purchasing our product.
MODEL RTA-3805L
ASSEMBLY INSTRUCTIONS
REV.122020-1

•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.
P. 1 RTA-3805L P. 1

P. 2 RTA-3805L P. 2
A
x4
B
x2
C
x4
D
x1
Main structure Support structure Horizontal tube Corner structure
MAIN PARTS LIST
E
x1
F
x2
Corner glass Main glass G
x8
Glide studs
LIST OF SCREWS
PART
QTY ITEM
H8M6x20mm
I4M6x40mm
J4M6x60mm
PART
QTY ITEM
K8M6x23mm
L4M6x8mm
M1M6
MAIN PARTS LAYOUT (FOR REFERENCE):
A
A
AA
BB
E
F F

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❸The replacement parts
service is limited to the
continental United States.If
you reside in Hawaii, Puerto
Rico, U.S. Dependencies or
other countries, please
contact the supplier from
where the unit was
purchased.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate (in models with
wood, MDF or fiber boards) might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate (in models with
wood, MDF or fiber boards) to reveal the hole’s
actual size.
P. 3 RTA-3805L P. 3

ASSEMBLY STEPS
Insert the glide studs Ginto the bottom of all the structures A.
STEP 1
Hardware:
G8
Pcs
P. 4 RTA-3805L P. 4
Assemble the support structure Bin between the main structures Awith
screws Hbut leave them loose.
STEP 2
Hardware:
H
M6x20
8
Pcs
M
A
G
(Top)
Do not tighten any screws in this step, leave them all loose.
A
A
B
A
A
B

P. 5 RTA-3805L P. 5
With the help of another person, assemble the horizontal tubes Cto:
-The structure Awith screws I on the left,
-The structure Aand the corner structure Dwith screws Jon the right.
It is recommended that the second person continue holding the corner
structure for the next step.
STEP 3
Hardware:
I
M6x40
2
Pcs
J
M6x60
2
Pcs
M
A
C
D
Do not tighten any screws in this step, leave them all loose.
A
C
J
I
The tabs on D go
facing UP.
X√
The holes on C go
oriented vertically.
J
I
C
C
D
The holes on C go
oriented vertically.
STEP 4
Hardware:
I
M6x40
2
Pcs
J
M6x60
2
Pcs
M
A
A
Do not tighten any screws in this step, leave them all loose.
With the help of another person, assemble the horizontal tubes Cto:
-The structure Awith screws I on the right,
-The structure Aand the corner structure Dwith screws Jon the left.

P. 6 RTA-3805L P. 6
With the help of another person, carefully place the glass tops over the
frame, and assemble:
-The corner glass Eto the corner structure Dwith screws L from
underneath, through the frame and into the round metal discs.
-The Main glasses Fto the bars Cwith screws Kfrom underneath,
through the frame and into the round metal discs.
STEP 5
Hardware:
K
M6x23
8
Pcs
L
M6x8
4
Pcs
M
Please note that the glasses won’t necessarily align perfectly, and might
look little uneven or with small gaps. This is considered normal, but if the
gap or misalignment is by more than a quarter of an inch (8mm), you can
try improving the leveling and close the gaps as much as possible by
adjusting the frame and the glide studs. Once the adjustments have
been done, you can proceed to tighten all the screws used from step 2
through step 5.
STEP 6
Hardware:
M
E
Do not tighten any screws in this step, leave them all loose.
F
KL
F
K
K
K
K
K
LL
K
Adjusting the innermost
glide studs might help
leveling the glasses.

ALL DONE!
Give yourself a nice pat on the back. You did a
great job!
P. 7 RTA-3805L P. 7

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop.
•Do not sit on the unit or lean against it.
•Do not allow small children to play under or over the unit.
•Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be
lifted by at least 2 persons when moving in the same or adjacent rooms, preferable 3
persons with one person at each end and one holding the corner.
•Before moving the unit, make sure to secure or remove any object that is heavy or
might fall off.
•When lifting the unit, use both hands and bend your knees, not your backs.
•When transporting the unit to places far away, protect and secure the unit to avoid
damage in transit.
•The glass is made of safety tempered glass. The safety feature is that when breakage
occurs, the glass shatters into many tiny pieces minimizing the risk of serious injuries.
If the glass breaks, do not handle the pieces with your bare hands, take some pictures
and contact Customer Service immediately.
•Shall any part of the unit become defective during the warranty period, replacement
parts might be available to you at no charge. Please refer to the last pages on this
manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes
liability for damages or consequences due to accidents, incorrect assembly,
negligence, improper use, modifications, or not heeding the above warnings.
WEIGHT LIMITS
P. 8 RTA-3805L P. 8
= 110 Lbs. (50 Kg)
= 66 Lbs. (30 Kg)
AA
B

RTA Products, LLC warrants to the Original Purchaser who acquired anew product from
RTA Products or its authorized resellers that this product will be free from defects in its
workmanship and materials, under normal use and service conditions, as described
herein."Defects" as used in this warranty, is defined as any imperfections that impair the
use of the furniture or product.RTA Products LLC will replace any defective part, at its
discretion, and without charge to the original purchaser other than the freight from the end
consumer to RTA Products.
Replacement parts can only be supplied if parts are available.Items out of production
may be unavailable.This warranty will be effective for the applicable time period
beginning the date of purchase on your original sales receipt.RTA product’s obligation
under this warranty is limited to repairing or replacing products or parts as provided
herein.This product has been designed for and is intended for office and home-office use
only.This warranty is Original Purchaser’s sole remedy for product defects, and this
warranty does not extend to any product, or damage to any product, caused by or
attributed to abuse or misuse, products used for commercial or rental purposes, use
modifications of, or attachments to the product, and products or parts not used,
maintained, or extended hereunder is in lieu of any and all other warranties, express or
implied, including without limitations any implied warranty or merchantability or of fitness
for aparticular purpose.Please note, all desks made with PVC Laminate surface should
not be exposed to direct sunlight, as it may damage the material.Damage of this nature
is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential
damages.This warranty is limited to merchandise purchased in the Continental United
States.Some States do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.This warranty
gives you specific legal rights.You may also have other rights that may vary from state to
state.
RTA Products will advise you of the procedure to follow in making warranty claims.The
following are the procedures for warranty claims:
a. Call us Monday –Friday, from 9am-5pm (Eastern Time) at [phone] to explain
the defect and give your name, address and phone number.Please have ready the
model number of our product, date and place of purchase.You can also write to us by
e-mail to [e-mail] and include the same information.
b. If we determine that replacement will remedy the situation, and in order to determine
the extent or the cause of the defect, purchaser will need to send the part in question
at purchaser’s expense.Once we receive the part, we will examine it and determine
whether the claim is valid (or not), and then proceed to send the replacement.We will
ship the replacement at our expense.
P. 9 RTA-3805L P. 9
TECHNI MOBILI WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY
TV Stand/Entertainment Center: 2 YEAR WARRANTY

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: [e-mail]
P. 1 0 RTA-3805L P. 1 0