Techni Mobili RTA-914LD User manual

Thank you for purchasing our product.
MODEL RTA-914LD
ASSEMBLY INSTRUCTIONS
REV.022021-0

•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.
P. 1 RTA-914LD P. 1

P. 2 RTA-914LD P. 2
1
x1
2
x1
3
x1
4
x1
Bottom panel for
left cabinet
Left panel for left
cabinet
Back panel for left
cabinet
Right panel for left
cabinet
MAIN PARTS LIST
5
x1
6
x1
7
x1
8
x1
Back-Left
horizontal panel
Long Left tabletop Right panel for
right cabinet
Bottom panel for
right cabinet
9
x1
10
x2
Middle shelf for
right cabinet
Back panel for
right cabinet
11
x1
12
x2
Left panel for
right cabinet
Back-Right
horizontal panel
13
x2
14
x1
Short Right
tabletop
Corner vertical
support panel
15
x2
16
x1
Door for right
cabinet
Door for left
cabinet
17
x2
18
x2
Drawer front
panel
Drawer right
panel
19
x2
20
x2
Drawer left
panel
Drawer
bottom panel
21
x2
Drawer back
panel
right cabinet

MAIN PARTS LAYOUT (FOR REFERENCE):
P. 3 RTA-914LD P. 3
1
LIST OF HARDWARE, SCREWS AND FITTINGS
PART
QTY ITEM
A28 M6x30
Wooden dowels
B22 M5x31
Bolts
C22 M12x9
Cam locks
D19 ST3.5x40
(Flanged head)
E6ST3.5x40
(Flat head)
F13 ST3.5x25
G50 ST4x12
H16 ST3x12
I22 15mm plastic
adhesive
covers
J16 M4x23
nails
PART
QTY ITEM
K9
12x12x6mm
Nail-in glide
stud
L5128mm
Handle
M515x15x40mm
Angle bracket
N2
Sets
Sliders, Set
of 4 pcs
O6
26mm
hinges with
5mm shim
P260x60mm
Metal plate
Q1
16x8x8mm
Plastic door
stopper
R1Touch-up
NOTE: You will need for the assembly a
Phillips screwdriver and mallet/hammer
(not included).
1
2
3
4
5
6
7
8
9
10
10
11
12
13
14
15 15
16
17
17
18
19
19
20
21

P. 4 RTA-914LD P. 4
☛
☛
This unit uses cam bolts and locks. The following explains how to use them.
☛
☛
This unit uses cam bolts and locks. The following explains how to use them.
This unit uses cam bolts and locks. The following explains how to use them.
This is not an assembly step; it is a guide for when you are actually doing the
This is not an assembly step; it is a guide for when you are actually doing the
assembly using this kind of hardware.
Cam Bolt Cam Lock
1. Screw the bolt into the
corresponding panel.
2. Place the other panel over the
panel with the bolt, then insert the
cam lock to join the bolt’s head.
If the cam lock does not want to
enter, check its proper alignment.
There might be a very small gap
between the panels which is normal.
3. Turn the cam lock clockwise. This
will lock the parts together and will
close any gaps.
Alignment: The cross
points towards the panel
with the bolt.

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❸The replacement parts
service is limited to the
continental United States.If
you reside in Hawaii, Puerto
Rico, U.S. Dependencies or
other countries, please
contact the supplier from
where the unit was
purchased.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P. 5 RTA-914LD P. 5

ASSEMBLY STEPS
Insert the dowels Ainto the corresponding holes in panels 1, 2, 3, 4, 7,
8, 9, 11, 18 and 19.
STEP 1
Hardware:
A
Dowels
28
Pcs
(NOT INCLUDED)
P. 6 RTA-914LD P. 6
Separate all the sliders pieces N according to their shape (no assembly
is done here):
-The “Flat” ones will be used in the next step.
-The “L” shaped go on the drawer and will be used until step 25.
1
STEP 2
Hardware:
N
Sliders
2
Sets
1
98
23
411
7
18
18 19
19
“L shaped”: Use until step 25
(on the drawer)
RIGHT
LEFT
“FLAT”: Use on step 3
(inside the unit)
RIGHT
LEFT

P. 7 RTA-914LD P. 7
With panels 2and 4oriented as shown, attach to them the flat sliders N
with screws H. The wheels go towards the front and facing down. For
best results, attach at the front of the panels first.
STEP 3
Hardware/Tools:
H
ST3x12
8
Pcs
N
FLAT
4
pcs
(NOT INCLUDED)
Wheel goes at
front and
facing down.
Hole at the front.
(Front)
(Front)
4
(Front)
4
2
(Front)
2
best results, attach at the front of the panels first.
Attach the sliders on these holes

P. 8 RTA-914LD P. 8
Assemble panel 2to panel 1with screws Das shown.
Assemble panel 3to panel 2with screws D.
2
1
STEP 4
Hardware/Tools:
DST3.5x40
(Flanged)
2
Pcs
(NOT INCLUDED)
1
2
(Top)
STEP 5
Hardware/Tools:
DST3.5x40
(Flanged)
2
Pcs
(NOT INCLUDED)
3
2
1

P. 9 RTA-914LD P. 9
Assemble the panel 4to panel 1with one screw E on the top hole only,
then use screws Dto secure panels 1, 3and 4as shown. Finally, attach
the glides Kto the bottom of the panels 2and 4.
STEP 6
Hardware/Tools:
DST3.5x40
(Flanged)
4
Pcs
EST3.5x40
(Flat)
1
Pcs
K
Glide studs
4
Pcs
(NOT INCLUDED)
(Top)
2
13
4
(Top)
D
E
Screw E is
only for the
top hole on
panel 4.
D
D
K
Assemble panels 8 and 9 to panel 7with screws D.
STEP 7
Hardware/Tools:
DST3.5x40
(Flanged)
3
Pcs
(NOT INCLUDED)
(Top)
8
9
7

P. 1 0 RTA-914LD P. 1 0
Assemble panel 11 to panels 8and 9with screws D.
With the help of another person, flip over the parts assembled in step 8,
and assemble panels 10 to panels 7and 8with screws D, and to panel
11 with screw D for the bottom and screw E for the top. Finally, attach
the glides Kto the bottom of panels 7and 11.
This illustration shows the same parts
from step 9 but view from the left
8
STEP 8
Hardware/Tools:
DST3.5x40
(Flanged)
3
Pcs
(NOT INCLUDED)
9
11
STEP 9
Hardware/Tools:
DST3.5x40
(Flanged)
5
Pcs
EST3.5x40
(Flat)
1
Pcs
K
Glide studs
4
Pcs
(NOT INCLUDED)
8
7
10
10
11
This illustration shows the same
parts from step 10 but flipped over
IMPORTANT:
On this side,
E goes at the TOP,
D goes at the BOTTOM.
E
D
D
D
D
D
K

P. 11 RTA-914LD P. 11
Attach the bolts Bto panels 4, 5and 11 as shown.
STEP 10
Hardware:
B
Bolts
6
Pcs
(NOT INCLUDED)
4
5
11
In panel 5 attach to the
holes closer to the edge.
Attach the glide Kto the bottom of panel 14, then assemble the panel to
panel 5 with screws F as shown.
STEP 11
Hardware:
FST3.5x25
3
Pcs
K
Glide stud
1
Pc
(NOT INCLUDED)
5
14
Panel 14 attaches to
panel 5 at 16mm
(3/4”) from the edge
K

P. 1 2 RTA-914LD P. 1 2
With the help of another person, join panel 5to panel 4. Then insert the
cam locks Cin panel 5making sure they are aligned, and turn the cam
locks as shown and as explained in page 4. Finally, cover the cam locks
with I.
STEP 12
Hardware:
C
Cam locks
2
Pcs
I
Covers
2
Pcs
(NOT INCLUDED)
Cam lock
alignment
C
I
5
4
Cam lock
alignment
alignment
C
I
I
5
With the help of another person, join panel 12 to panels 5 and 11. Then
insert the cam locks Cin panel 12 making sure they are aligned, and
turn the cam locks as shown and as explained in page 4. Finally, cover
the cam locks with I.
STEP 13
Hardware:
C
Cam locks
4
Pcs
I
Covers
4
Pcs
(NOT INCLUDED)
the cam locks with
I
.
Cam lock
alignment
C
I
I
Cam lock
alignment
C
I
12
11
5

P. 1 3 RTA-914LD P. 1 3
Attach the brackets Mto the panels 3, 5, 10 and 12 with screws Gas
indicated, making sure their corner goes flushed with edge of the panels.
Then insert the door stopper Qinto the corresponding hole on panel 4.
Attach to panels 15 and 16 the handles Lwith screws F, and the hinges
Owith screws Gas shown.
STEP 14
Hardware:
G
ST4x12
10
Pcs
M5
Pcs
QDoor
stopper
1
Pc
(NOT INCLUDED)
STEP 15
Hardware:
F
ST3.5x25
6
Pcs
G
ST4x12
12
Pcs
L3
Pcs
O6
pcs
(NOT INCLUDED)
5
12
10
16
15
15
F
G
For the handles
For the hinges
FG
3
M
M
Q

P. 1 4 RTA-914LD P. 1 4
Assemble the hinges Ofrom the small door 16 to panel 2, and from the
large doors 15 to panels 7and 11 respectively with screws Gas shown.
If the doors don’t open and close smoothly, adjust their alignment by
loosening up the indicated screws, adjusting the door position, then re-
tightening the screws.
STEP 17
(NOT INCLUDED)
large doors
to panels
respectively with screws
STEP 16
Hardware:
G
ST4x12
12
Pcs
(NOT INCLUDED)
215
7
11
15
15
16
Loosen these 2 screws
to adjust the height
Loosen this screw
to adjust side-to-side
Loosen this screw
to adjust the depth

P. 1 5 RTA-914LD P. 1 5
Place the tabletops 6and 13 upside-down over a blanket to protect their
surfaces, and attach the bolts Bin the outermost holes as shown.
With the help of another person, carefully place the tabletops 6and 13
over the frame built in step 16, then insert the cam locks Cin the
corresponding holes on panels 2, 4, 7and 11, and turn them to lock the
pieces as explained in page 4. Finally, cover the cam locks with I.
STEP 18
Hardware:
B
Bolts
8
Pcs
(NOT INCLUDED)
STEP 19
Hardware:
C
Cam lock
8
Pcs
I
Covers
8
Pcs
(NOT INCLUDED)
6
13
27
11
4
613
Cam lock
alignment
alignment
C
I

P. 1 6 RTA-914LD P. 1 6
Working from underneath, and using screws G, secure the brackets M to
the tabletops 6and 13, then attach the metal plates Pin between the
panels as shown.
For each of the 2 small drawers, assemble the drawer side panels 18
and 19 to the drawer back panel 21 with screws Eas shown.
STEP 20
Hardware:
G
ST4x12
18
Pcs
P2
Pcs
(NOT INCLUDED)
613
View from
underneath:
STEP 21
Hardware/Tools:
EST3.5x40
(Flat)
4
Pcs
(NOT INCLUDED)
21
19
18
MPM

P. 1 7 RTA-914LD P. 1 7
For each of the 2 small drawers, attach the bolts Bto the indicated holes on
panel 17. Then join the panel to panels 18 and 19. Then insert the cam
locks Cinto panels 18 and 19 making sure they go aligned, and turn them to
lock the pieces as explained in page 4. Finally, cover the cam locks with I.
STEP 22
Hardware/Tools:
B
Bolts
8
Pcs
C
Cam locks
8
Pcs
I
Stickers
8
Pcs
(NOT INCLUDED)
. Finally, cover the cam locks with
Cam lock
alignment
CI
B
17
19
18
17
For each drawer, assemble the handle L to the drawer front panel 17 with
screws F from inside.
The groove on panel 17 go
on the bottom of the drawer.
The illustration shows
the drawer upside-down.
STEP 23
Hardware/Tools:
F
ST3.5x25
4
Pcs
L
Handle
2
Pcs
(NOT INCLUDED)
STEP 24
Hardware/Tools:
JNails
16
Pcs
(NOT INCLUDED)
For each drawer, place the panel 20 on the bottom of the drawer making
sure it enters into the groove of panel 17, then secure panel 20 to panels 18,
19 and 21 with nails Jas shown.
19
and
21
with nails
J
as shown.
Panel 20 enters into
the groove of panel 17.
17 L
17
20
19
20
21 18

P. 1 8 RTA-914LD P. 1 8
STEP 25
Hardware/Tools:
H
ST3x12
8
Pcs
N
“L” shape
4
Pcs
(NOT INCLUDED)
For each drawer, assemble the L-Shaped sliders O to the bottom of the
drawer with screws H.
IMPORTANT: Please pay attention to the orientation of the sliders as
indicated.
ATTENTION:
Incorrect: Will raise 1”
and drawer won’t fit!
Correct:
The wheels go towards
the back of the drawer
Insert the drawers into the unit starting with the bottom one. You might need
to insert them an angle with the front facing down.
If the drawers don’t fit, please review the assembly of the steps 3and 25.
STEP 26
Attach the sliders through the indicated holes

ALL DONE!
Give yourself a nice pat on the back. You did a
great job!
P. 1 9 RTA-914LD P. 1 9