Techni Mobili RTA-8070 User manual

M6x40mm, x4
Washers, x4
ASSEMBLY INSTRUCTIONS FOR CHAIR MODEL
RTA-8070
PARTS LIST
ATTENTION: Before you begin the assembly,
make sure that all parts are included in good
condition.
ATTENTION:
⚠Follow the in truction tep by tep.
⚠To avoid mi alignment , leave the crew loo e and do not tighten them until all are in their re pective place .
⚠Do not overtighten or force the crew a they could break, trip, or damage the thread of the hole .
⚠U ing the wrong ize of crew on a part could re ult in damage to the crew or the part.
E
F
C
B
A
J
ABackrest, x1
Beat, x1
DMechanism,
x1
EHydraulic
Gas Lift, x1
F
Ctar Base, x1
H
Caster, x5
I
Hole Covers
J
M6x20mm, x4
L
K
In ert the ca ter (F) into the leg of
the ba e (C) u ing pre ure, then
place the ga lift (E) in the middle of the
ba e a hown.
Proceed to tighten the crew (H) and
then cover the top hole with the long
cover (K) and the bottom hole with the
hort one .
(Backre t viewed
from behind)
X1 Right
X1 Left
(Mechanism)
(Armrest to Backrest)
Allen Wrench, x1
Tighten well all the crew before you
it on the chair for the fir t time.
NOTE: When you are seated
on the chair, not looking at it.
GArmrest
M6x25mm, x4
(Armrests to eat)
I
X2 Long X2 hort
A emble the armre t (G) to the
backre t (A) on their re pective ide
u ing crew (H), but leave the crew very
loo e to allow flexibility on the next tep.
G (RIGHT)
G (LEFT)
H
A emble the armre t (G) to the
eat (B) u ing crew and wa her
(J) a hown and tighten them.
G (RIGHT) G (LEFT)
U ing crew (I), a emble the
mechani m (D) with it handle facing
to your left and it knob toward the front of
the chair a hown. K (LONG)
K (SHORT)
Place the eat over the ba e making
ure that the tip of the ga lift enter
in the hole of the mechani m.
(Armrests)
(backre t viewed
from behind)
(FRONT OF CHAIR)

CHAIR’ FUNCTION :
(1) To raise or lower the chair’s height, pull UP the lever that is under the seat. The chair goes down while
sitting on it, or up if you lift your body.
(2) To make the chair tilt, pull the same lever OUT horizontally to unlock this function, and IN to lock again.
(3) To adjust the tension for the tilting function, turn the mechanism’s knob in either direction to apply more
or less tension.
(4) You can flip UP the armrests to use as an armless chair.
WARNING :
•Do not stand up on the chair or use it as ladder.
•Use the chair to seat only one person at a time.
•Do not use the chair if parts are damaged or if screws are loose or missing.
•Do not seat near the edge of the seat and always sit properly on the chair to avoid going beyond your balance point and fall off the chair.
•The chair is intended for teenagers and adults. If small children are using the chair, please keep close observation on them.
•Do not allow small children to play with the chair.
•Not paying attention to these warnings could result in severe injuries.
CARE AND MAINTENANCE:
•To clean the chair it is recommended to use a soft cloth lightly damped in a solution of smooth soap and water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean any part of the chair.
•Before applying a cleaning agent, test on a small hidden area of the chair, like underneath the seat.
•Do not expose the product to direct sunlight or to extreme environmental conditions.
•Every 4 months, inspect the chair completely and make sure that all screws are tighten.
(1)/(2)
(3)
(4)