Technoline RADIO CONTROLLED PROJECTOR CLOCK User manual

RADIOCONTROLLEDPROJECTORCLOCK
User’sinstructions
P17018365A0173200E

The multifunctional clock is equipped with many functions
providing thorough information to you. The receiver unit has
a clear, easy-to-read display that shows minimum/maxi-
mum indoor and outdoor temperature, as well as time and
date. It is able to receive and display readings from up to 3
remote sensors.
The 433 MHz technology means no wire installation is
required and you can place the sensors anywhere you like.
With radio controlled function, the current time and date are
automatically synchronized with the time signal transmitted
from Germany (DCF77) / UK (MSF) / USA (WWVB) (It
depends on which version you purchase).
POWER
Main unit: 4.5V, use 3 x AA 1.5V
Remote sensor: 3V, use 2 x AA 1.5V
DIMENSION
Main unit: 136(W) x 91(H) x 40(D) mm
Remote sensor: 65(W) x 115(H) x 20(D) mm
15

114
MAINFEATURES:
WEATHERSTATION:
1. SNOOZE/LIGHT key:
- Turn on the projector and backlight for 5 seconds.
- Stop the current alarm when it is sounding and enter
into snooze mode.
2. TIME WINDOW:
- Displays normal time and day of the week.
3.DATE ANDTEMPERATURE WINDOW:
- Shows indoor/outdoor temperature, alarm time and the
date
SPECIFICATION
MAIN UNIT
Operating range: -5°C~50°C
23° F~122°F
Resolution: 0.1°C/°F (above -10°C/32°F)
1°C/°F (below -10°C/32°F)
Radio controlled signal: WWVB/DCF/MSF
REMOTESENSOR
Operating range: -20°C~60°C
-4°F~140°F
Resolution: 0.1°C/°F (above -10°C/32°F)
1°C/°F (below -10°C/32°F)
RF transmission frequency: 433MHz
No. of remote sensor: up to 3 units
RF transmission range: maximum 50 meters
Temperature sensing cycle: around 60-64 seconds
1
4
5
6
7
8
9
13
12
11
14
18
16 10
15
ON
OFF
17
2
3

2
13
4. TIMEkey:
- Press it to switch between Month/Date and alarm time
mode.
- Press and hold it for 2 seconds to enter normal time
setting.
- In normal time setting, press it to step the setting items.
5.ALARM key
- In normal time display, press it to turn on/off ALM1 &
ALM2.
- In ALM1 / ALM2 mode, press it to turn on/off alarm and
pre-alarm function.
- Press it to stop the current alarm when the bell is ringing
and turn off the alarm and snooze function.
- In alarm time mode, press and hold it for 2 seconds to
enter alarm time setting.
- In alarm time setting, press it to step the setting items.
6. UP key
- In setting mode, press it to increase the setting values.
- In normal time mode, press it to switch among Channel
1, 2 and 3.
7. DOWNkey
- In setting mode, press it to decrease the setting values.
- In normal time mode, press it to switch among 12/24
hour format.
TEMPERATURETREND
The temperature-trend indicator shows the trends of
changes in the forthcoming few minutes. Arrows indicate a
rising, steady or falling trend.
LOWBATTERYINDICATOR
Whenthe LCD becomes dim, replace with3 xAAsize batteries
at once; while if the low battery indicator “” displays in the
outdoor temperature window, it indicates that the battery
power of the transmitter is not enough, and you should replace
with 2 x AA size batteries at once.
NOTE:
Attention! Please dispose of used unit or batteries in an
ecologically safe manner.
Transmitter’s low battery indicator
Arrow indicator
Pressure trend Rising Steady Falling

312
8.MAX/MIN key
- Press it to check the minimum and maximum
temperature records.
9. PROJECTOR
- Project the time and indoor/outdoor temperature
(automatically switch between indoor and outdoor
temperature in every 5 seconds. )
10. REVERSE key
- Press it to reverse the projected date.
11. FOCUS knob
- Adjust the quality of the projected date.
12. DC JACK
- To power the unit.
13. RECEIVE key
- Press it to receive the RC signal for reception testing.
14. °C/°F key
- Press it to switch between Celsius and Fahrenheit.
15. NIGHT LIGHT FUNCTION ON/OFF switch
- Slide it to turn on/off the night light function.
16. NIGHT LIGHT SENSOR
- Turn on the function, the night light will turn on
automatically in dark environment.
VIEWINGTHE CHANNEL
The default channel is Channel 1. In normal time mode,
press “UP” key to view the channels from 1 to 3. Besides,
the channels can automatically switch by pressing and hold-
ing the “UP” key for 2 seconds, with “beep” tone.
USINGTHE PROJECTOR
Press the SNOOZE/LIGHT key to turn the projector on, ro-
tate the projector to project the light beam to a dark back-
ground within 1-4 meters, the projected data will be dis-
played on the dark background as following diagram.
Note:
1. Press the SNOOZE/LIGHT key once, back light and
the projection last for 5 seconds, then press the
“” key will reverse the projected data.
2. If using DC power, the projected data will be always
on.
3. The rotate angle of the projector is ±90º.
4. Adjust the quality of the projected data by adjusting the
FOCUS knob.

4
11
17. RESET key
- Press it to reset all values to default values.
- In case of malfunction, the unit may be required to reset.
18. BATTERY COMPARTMENT:
- Accommodates 3 x AA size batteries (alkaline batteries
recommended).
TRANSMITTER
1. LED indicator:
- Flashes when the remote unit transmits a reading.
2. CHANNEL SLIDE SWITCH:
- Assign the transmitter to Channel 1, 2 or 3.
3. RESET:
- Press it to restart the transmitter.
4. BATTERYCOMPARTMENT:
- Accommodates 2 x AA size batteries.
NOTE:
1. If no signals are received or the transmission is
interfered, “—” will appear on the LCD.
2. Relocated the clock or transmitter in other positions
and make sure the transmission is within the effective
range of 80m approx.
3. After several trails in vain, please reset the clock
thoroughly. Try out where your multifunctional alarm
clock receives the signals best.
CHECKING AND DELETING MAX/MIN TEMPERATURE
RECORDS
1. Press “MAX/MIN” key once to check the maximum
temperature records. Press it twice to check the
minimum records. Press it again to exit.
2. Press and hold “MAX/MIN” for 3 seconds to delete the
maximum and minimum temperature records, with
“beep” tone.
5
13
2
4
6
7
MAX temperature record
MIN temperature record

510
5. BATTERYDOOR
6. WALL-MOUNTING HOLDER:
- Use it to support the transmitter on the wall.
7. TABLESTAND:
- Use it to stand the transmitter on the desktop.
BEFOREUSINGTHETRANSMITTER
1. Remove the battery door.
2. Insert2 xAAsize batteries into the battery compartment.
Make sure you insert them the right way according to
the polarity information marked on the battery
compartment.
3. Replace the battery door.
NOTE:
1. Once the channel is assigned to one transmitter, you
canonlychange it by removing the batteries or resetting
the unit.
2. Avoid placing the transmitter in direct sunlight, rain or
snow.
WEATHERSTATION:
1. If using the DC Adaptor to power the clock, plug the
adaptor into the DC jack. If using battery, remove the
to turn on both ALM1 and ALM2, with the bell icons
display on the LCD. Press it again to turn off both
ALM1 and ALM2, with the icons disappear.
3. In ALM1/ALM2 mode, press alarm key once to turn on
ALM1/ALM2,press it twice to turn on pre-alarm function,
with the icon “ ” displays on the LCD. Press it again
to turn off both alarm and pre-alarm functions, with the
icons disappear.
NOTE:
1. To turn on temperature pre-alarm, ALARM must be on.
2. The temperature pre-alarm can sound 30 minutes
earlier than the alarm only when the outdoor
temperature is below -3°C (26°F).
3. If no key is pressed during the alarm period, the alarm
willturn off automatically. You can also press “SNOOZE/
LIGHT” key to stop the current alarm and enter the
snooze mode. With the bell icon keep flashing.
4. Once the snooze function is turned on, the 4-step
crescendo alarm will sound in 5-minute interval. The
alarm duration is 120 seconds.
5. The snooze function won’t stop unless you press
“ALARM” key toturn off the alarm and snooze function.
READINGINDOOR/OUTDOORTEMPERATURERECORDS
Change the temperature unit to °C for Celsius or °F for Fahr-
enheit by pressing “°C/°F” key.

6
9
battery door and insert 3 x AA batteries into the battery
compartment. Make sure you insert the batteries the
right way according to the polarity information marked
on the battery compartment.
2. Replace the battery door.
3. Press the “RESET” key to re-start the clock and it will
synchronize the channels of transmitter automatically.
NOTE:
1. The building material and the position of the receiver
and transmitter affect the effective range. So try various
locations to obtain the best result.
2. Place the units away from metal objects and electrical
appliances to minimize the interference. Position the
receiver and transmitter within the effective
transmission range: 80m in usual circumstances.
RECEPTIONOFRADIO CONTROLLED TIMESIGNAL
The time and date are radio-controlled. The current time
and date are automatically synchronized with the time
signal transmitted from Germany (DCF 77)/U.K. (MSF)/
USA(WWVB).
When used for the first time (after inserting the batteries or
pressing the “RESET” key), the clock will start to receive the
RC signal in 5minutes with the signal strength indicator
flashing.
5. Press “TIME” key to save and exit the setting or let it exit
automatically 30 seconds later without pressing any key.
ALARMANDSNOOZE SETTING
1. In normal time mode, press “TIME” key to select the
ALM1or ALM2.
2. In ALM1/ALM2 mode, press and hold “ALARM” key for
2 seconds until alarm Hour digit flashes.
3. Press “UP” or “DOWN” key to change the value.
4. Repeat the above operations to set time in this order:
Hour > Minute
5. Press “ALARM” key to save and exit the setting, or let it
exit automatically 30 seconds later without pressing
any key.
NOTE:
1. The alarm will be automatically turned on when you
set the alarm time with the icon “” or “”displayed.
2. The dual-alarm (ALM1&ALM2) design of this unit will
provide you with more convenience, and you can set
two-alarm time if needed.
USINGALARM&TEMPERATURE PRE-ALARM FUNCTIONS
1. Set the alarm time as described in the previous section.
2. In normal time mode,press “ALARM ” key once to turn
on ALM1, press it twice to turn on ALM2, press it thrice

7 8
SIGNALSTRENGTHINDICATOR
The signal indicator displays signal strength in 4 levels.
Wave segment flashing means time signals are being
received. The signal quality could beclassified into four types:
NOTE:
1. Everyday the unit will automatically search for the time
signal at 2:00, 8:00, 14:00 and 20:00.
2. Always place the unit away from interfering sources
such as TV set, computer, etc.
3. Avoid placing the unit on or next to metal plate.
4. Closed area such as airport, basement, tower block
or factory is not recommended.
5. Do not start reception on a moving article such as
vehicle or train.
MANUALTIME SETTING
Ifyou are out of the reach of the Radio Controlled Transmitter
or if the reception is not reachable, the time can be set
manually. As soon as the transmitter is received again, the
clock will automatically synchronize with received time.
MSF/DCF Version:
1. In normal time mode, press and hold “TIME” key for 2
seconds until the Year digit flashes.
2. Press “UP” or “DOWN” key to change its value.
3. Press “TIME” key again, Month digit flashes, press
“UP” or “DOWN” key to change its value.
4. Repeat the above operation to set the time in this order:
Year > Month > Date > Hour > Minute > Second > Day
Language .
5. Press “TIME” key to save and exit the setting or let it exit
automatically 30 seconds later without pressing any
key.
WWVB Version:
1. In normal time mode, press and hold “TIME” key for 2
seconds until the Time zone map flashes.
2. Press “UP” or “DOWN” key to select the proper time
zone.
3. Press “TIME” key again, Year digit flashes, press “UP”
or “DOWN” key to change its value.
4. Repeat the above operation to set the time in this order:
Time zone map > Year > Month > Date > DST ON/OFF >
Hour > Minute > Second > Day Language.
No signal quality Weak signal quality
Acceptable signal quality Excellent signal quality