Tecnoware Ups Pro User manual

Uninterruptible Power Supply
Ups Pro
User’s manual
Manuale utente

Index
Safety Warnings ................................................................................ 1
1 Introduction ................................................................................. 2
2 eneral Characteristics ................................................................... 3
3 Receipt and site selection ................................................................ 3
4 EXTERNAL DESCRIPTION .................................................................. 4
4.1 Front Panel ............................................................................. 4
4.1.1 LCD Display .................................................................................5
4.2 Rear Side ................................................................................ 6
5 Electrical Installation and First Start Up ............................................... 7
6 Functioning ................................................................................. 8
6.1 Normal Mode ........................................................................... 8
6.2 Battery Mode ........................................................................... 8
6. Low Battery and Automatic Restart ................................................. 8
6.4 Load Control ............................................................................ 9
6.5 Fault Condition ........................................................................ 9
7 Communication Interfaces ............................................................... 9
8 Technical Characteristics ................................................................ 10
9 Maintenance ............................................................................... 11
9.1 UPS Cleaning ......................................................................... 11
9.2 Battery ................................................................................ 11
9. Operator Safety ...................................................................... 11
10 Troubleshooting ........................................................................... 12
Conformity to the European Directives ................................................... 13
Product Disposal ............................................................................... 13
Lead Batteries ................................................................................. 13
© Copyright 2012 TECNOWARE s.r.l. All rights reserved.
All trademarks are property of their respective owners.
TECNOWARE s.r.l.
Via Montetrini, 2E – Molino del Piano – Florence – Italy
www.tecnoware.com
Edition: March 2012 – version: 1.0
No part of this manual may be reproduced, even partially, without the
authorisation of TECNOWARE s.r.l.
TECNOWARE s.r.l. reserves the right to change specifications at any time
and without notice.

Indice
Avvisi di Sicurezza ............................................................................ 14
1 Introduzione ............................................................................... 15
2 Caratteristiche enerali ................................................................. 15
3 Ricevimento e Collocazione ............................................................. 16
4 Descrizione Esterna ....................................................................... 17
4.1 Pannello Frontale .................................................................... 17
4.1.1 Display LCD ............................................................................... 18
4.2 Retro................................................................................... 19
5 Installazione e Prima Accensione ...................................................... 20
6 Funzionamento ............................................................................ 21
6.1 Modo Normale ........................................................................ 21
6.2 Modo Batteria ........................................................................ 21
6. Fine Autonomia e Riaccensione Automatica ..................................... 21
6.4 Controllo del Carico ................................................................. 21
6.5 Segnalazioni di Guasto .............................................................. 22
7 Interfacce di Comunicazione ............................................................ 22
8 Caratteristiche Tecniche................................................................. 23
9 Manutenzione .............................................................................. 24
9.1 Pulizia dell’UPS ...................................................................... 24
9.2 Batterie ............................................................................... 24
9. Sicurezza dell’Operatore ........................................................... 24
10 Anomalie ed Interventi ................................................................... 25
Conformità alle Direttive Europee ......................................................... 26
Smaltimento del Prodotto ................................................................... 26
Batterie al Piombo ............................................................................ 26

EN LISH
Ups Pro 1 User’s manual
User’s Manual - English
Safety Warnings
 Read this manual carefully and completely before installing and using the TECNOWARE Ups Pro
Uninterruptible Power Supply, which, from here after, will also be referred to as UPS.
 This manual should be kept close to the UPS and read before the UPS is installed and used.
 The UPS must be used only by properly trained personnel. To ensure correct and safe
operations, it is necessary that operators and maintenance personnel observe the general
safety Standards as well as the specific instructions included in this manual.
 Risk of electric shock: do not remove the cover. The UPS contains internal parts, which are at a
high Voltage and are potentially dangerous, capable of causing injury or death by electric
shock.
 There are no internal parts in the UPS, which are user serviceable. Any repair or maintenance
work must be performed exclusively by qualified technical personnel authorized by
TECNOWARE. TECNOWARE declines any responsibility if this warning is disregarded.
 Warning to the technical personnel authorized for Service: since internal components are
connected to the batteries, they will remain powered, and therefore dangerous, even after the
UPS has been disconnected from AC power mains. Before any repair or maintenance work,
disconnect the batteries, by removing the positive cable (red colour) from the positive pole of
the battery.
 It is compulsory to ground the UPS according to Safety Standards. The AC mains power supply
socket used to power the UPS must have an earth connection.
 In the event of AC main power supply failure (when the UPS works in Battery mode), do not
unplug the power supply cable to the UPS to ensure earth continuity to the connected loads.
 Since the AC mains power supply cable acts as a separation device, the AC mains power socket
used to supply the UPS and/or the rear side of the UPS must be accessible to easily disconnect
the cable in case of dangerous conditions.
 Risk of electric shock at the Output lines when the UPS is ON.
 Risk of electric shock at the Output lines while the unit is connected to the AC utility line.
 Do not obstruct ventilation slots or holes and do not rest any object on top of the UPS.
 Do not insert objects or pour liquids in the ventilation holes.
 Install the UPS indoors, in a protected, clean and moisture-free environment.
 Do not expose to the direct sun light.
 Do not keep liquids, flammable gases or corrosive substances near the UPS.

EN LISH
User’s manual 2 Ups Pro
1Introduction
Ups Pro is a Line Interactive Pure Sinewave UPS (Uninterruptible Power Supply) specifically designed to protect
your Mac Pro from any type of irregularities in the AC line (such as black-outs, under or over voltages, micro-
interruptions), which often cause damage to your Hardware and Software.
Under normal AC line condition, Ups Pro performs output voltage regulation and filters frequently occurring
electrical disturbances (such as transients, spikes, interferences, etc.), this protecting all devices connected to
the outlets, and recharging the batteries in an ideal way. In case of anomaly to the AC line, the UPS continues
feeding the protected equipment.
Ups Pro is equipped with a USB interface which can be used to notify a power failure or a low battery condition
directly to a computer: this makes it possible to automatically save your data during an extended black-out.
Read this manual carefully before using the Ups Pro; it includes important safety
warnings and useful advices for correct use and installation.
This manual is a guide that enables you to correctly install and use your Ups Pro. This
manual includes important SAFETY instructions for the operator, for the UPS correct
installation, and gives useful advice on the product and battery maintenance. For any
type of problem, please refer to this manual before calling the customer service.
Ups Pro is constantly being developed and improved: consequently, your unit may differ somewhat from the
description contained in this manual.
This manual includes the following models:
•Ups Pro (1500 VA)
In this manual Ups Pro will simply be referred to as UPS.

EN LISH
Ups Pro 3 User’s manual
2eneral Characteristics
Ups Pro has all the advanced features, which guarantee maximum reliability and safety:
•All functions are controlled by a microprocessor, giving full guarantee of high reliability.
•Output Voltage regulation through AVR (Automatic Voltage Regulation).
•Overload protection both in normal mode and in battery mode.
•High performance battery charger, which extends the battery medium life ensuring an optimal recharge.
•Start up even if the electrical network is not available.
•Automatic restart after an automatic shut down due to a low battery condition once the AC utility power
returns.
•Adapts automatically to 50 or 60 Hz input frequency.
•LCD display for the visualization of the Input and Output Voltage, Battery Level percentage, Load Level
percentage, functioning modes, alarm and fault conditions.
•Acoustic signals of various kinds indicating functioning modes and alarm/fault condition.
•Communication with the computer through USB interfaces.
•Fast swappable battery.
•High efficiency
•Maximum reliability
•Smart design and easy to use
3Receipt and site selection
Carefully remove the UPS from its packaging, and carry out a meticulous inspection. We recommend keeping the
original packaging in a secure place, in case you need to send the UPS for maintenance purposes. In case of
transport damage, notify the carrier and dealer immediately.
We recommend paying attention to the below points in order to choose a correct placement for your UPS:
•The UPS is designed to operate in a protected environment (e.g. offices). We therefore recommend
installing it in a place with very little or no humidity, dust or smoke.
•In all circumstances, see the “Technical Characteristics” chapter for environmental specifications and
check that the selected area meets these specifications.
•During normal operation the UPS discharges a minimal amount of heat. So it is necessary to leave at least
20 cm of unobstructed space all around the UPS in order to keep it properly ventilated.
•Do not obstruct ventilation holes.
•Do not insert objects or pour liquids in the ventilation holes.
•Do not rest any object on top of the UPS.
•Do not keep liquids, flammable gases or corrosive substances near the unit.
•Install the UPS on a properly tiled floor. Avoid the installation on a floor that is not tiled flat.

EN LISH
User’s manual 4 Ups Pro
4EXTERNAL DESCRIPTION
4.1 Front Panel
The front panel informs the user about operating status, alarm conditions and measurements. Front panel shown
below consists of two parts:
1. LCD display provides information about input and output voltage, battery level percentage, load level
percentage, functioning modes, alarm and fault conditions.
2. ON/OFF button: enables the user to turn ON/OFF the UPS.
Figure 1 – Front panel
1
2

EN LISH
Ups Pro 5 User’s manual
4.1.1 LCD Display
Please refer to figure 2.
Figure 2 –LCD Display
1. INPUT: the digits indicate the Input Voltage.
2. OUTPUT: the digits indicate the Output Voltage.
3. BATTERY LEVEL: is a four-segment light bar. This bar indicates the battery charging percentage as
explained below:
•
••
•0~25%: only 1 segment is on.
•
••
•25~50%: 2 segments are on.
•
••
•50~75%: segments are on.
•
••
•75~100%: all the 4 segments are on.
4. LOAD LEVEL: is a four-segment light bar. This bar indicates the Output Load percentage as explained below:
•
••
•0~25%: only 1 segment is on.
•
••
•25~50%: 2 segments are on.
•
••
•50~75%: segments are on.
•
••
•75~100%: all the 4 segments are on.
5. AC MODE: this icon is on to indicate the UPS is working in Normal mode.
6. BATTERY MODE: this icon is on to indicate the UPS is working in Battery mode.
7. LOW BATTERY: is on to indicate the Low Battery condition.
1
3
2
4
7 6
5

EN LISH
User’s manual 6 Ups Pro
4.2 Rear Side
Figure 3 – Rear Side
1. rounded AC Input power cable: Schuko type; to connect the UPS to the AC utility line.
2. rounded UPS Output receptacles: Italian/Schuko type, white colour, to supply critical loads.
3. rounded (ONLY FILTERED) Output receptacles: Italian/Schuko type, white colour, to supply NOT-critical
loads.
4. Computer Interface (USB connector): it is the communication USB port.
5. Input circuit braker: electrical specification: max current 7A, voltage 250 V.
The ONLY FILTERED Output receptacle (#3), protects only the devices connected from
overvoltage and disturbances of the AC line. Please connect ONLY the NON-critical
devices to the ONLY FILTERED Output receptacle.
In case of anomaly to the AC line (black-out), ONLY the UPS Output receptacles (white
colour, #2) continue supplying the correct power to all connected equipment. Please
connect all the non-critical devices to the UPS Output receptacles.
1
2 3
4
5
2
3

EN LISH
Ups Pro 7 User’s manual
5Electrical Installation and First Start Up
We advise you to follow the steps below explained for greater safety:
1. Switch off all the devices (Computer or other electronic devices) that need to be supplied by the UPS.
2. Connect the UPS Input power cable to the AC line outlet. It is mandatory to ground the AC line outlet
according to the Safety Standards. Carefully check the grounding, make sure that the utility power is
available, and that its range falls within the UPS specifications (refer to the “Specifications” chapter).
3. Press the ON/OFF button on the front panel: the UPS emits a brief acoustic signal, turns the LCD display on,
and performs a functioning SELF-TEST. Leave the UPS in Normal mode for at least 4 hours in order to
completely recharge the batteries.
4. Switch the UPS off (by pressing again the ON/OFF button).
5. Connect the devices to be supplied to the UPS outputs. Be sure all the devices have the main switch in ON
position.
6. Turn on the UPS again. Check that it starts working correctly and it doesn’t signal any sort of anomaly.
Moreover be sure that all the devices connected to the UPS outputs are working correctly. By LCD display
check if the Output load percentage is less than 100%; otherwise it is necessary to remove part of the Output
load.
7. Simulate a black-out by removing the AC Input line. The UPS starts working in Battery mode. Moreover the
UPS emits a brief acoustic signal every 10 seconds.
8. Be sure that all the devices connected to the UPS outputs are working correctly and the UPS doesn’t signal
any sort of anomaly.
9. Restore the AC Input line: after few seconds the UPS turns back in Normal mode.
Before using Ups Pro normally, leave it in Normal mode in order to charge the batteries completely as specified at
point . The batteries reach the 90% of their capacity after about 4 hours of recharge.
It is compulsory to ground/earth the UPS according to the Safety Standards.
Risk of electric shock at the Output lines if the UPS is ON, even when the UPS is not
connected to AC utility line.
Risk of electric shock at the Output lines while the unit is connected to the AC utility
line.
Risk of electric shock: do not remove the cover. The UPS contains internal parts, which
are at a high Voltage and are potentially dangerous, capable of causing injury or death
by electric shock.
There are no internal parts in the UPS that are user serviceable. Any repair or
maintenance work must be performed exclusively by qualified technical personnel
authorized by TECNOWARE. TECNOWARE declines any responsibility if this warning is
disregarded.
Disregard for these warnings may lead to a risk of electric shock to operators.

EN LISH
User’s manual 8 Ups Pro
6Functioning
6.1 Normal Mode
The UPS typically works in Normal mode: Input mains power is available and its amplitude is within specifications.
Ups Pro indicates the normal mode through the lighting of an icon on the display.
During Normal mode, the UPS recharges the batteries and keeps them in an optimal charging voltage.
6.2 Battery Mode
The UPS automatically runs in Battery mode if the AC Input Line voltage amplitude gets out of security limits (in
case of a black-out or over-voltage/low-voltage): in this case, the UPS supplies the required output power by its
internal battery and by the Inverter block.
The UPS automatically returns in Normal mode a few seconds after the AC Input Line is recovered.
The Battery mode is identified through the lighting of an icon on the display and an acoustic signal every 10
seconds.
6.3 Low Battery and Automatic Restart
In Battery mode, Ups Pro indicates the Low Battery condition whenever the battery reaches a charge level
allowing connected devices to operate for approximately one more minute.
The UPS warns operators of Low Battery through the lighting of an icon on the display and emitting an acoustic
signal every second.
If AC Input does not come back on within few minutes, the UPS shuts-down automatically thus preventing the
batteries from discharging excessively; the UPS stops supplying Output power, deactivates control panel indication
and goes to a waiting state. Once AC Input comes back on, the UPS restarts automatically and after some seconds
it goes back to work in Normal mode.
After a complete discharge, the UPS needs 4 hours to recharge completely the batteries. The UPS recharges
batteries automatically if it works in Normal mode or if it is off and connected to the AC Input Line.

EN LISH
Ups Pro 9 User’s manual
6.4 Load Control
The UPS indicates the Output Load level by LCD display (as described in the chapter 4).
When the Output load is higher than nominal value the UPS warns of Overload condition by LCD display, by
emitting a continuous acoustic alarm.
The UPS warns of an Overload less than 110% by acoustic alarm.
An Overload between 110% and 120% is accepted for about 0 seconds and after UPS switches automatically off.
The UPS switches immediately off if the Overload is higher than than 120%.
Once the requested power is back within range, the UPS switches automatically to the Normal mode.
Make sure that the UPS never indicates Overload condition.
Do not connect a load greater than rated value to the UPS (see POWER specifications in
the chapter “Technical Characteristics”), as this may damage the unit. In this case the
warranty is void.
6.5 Fault Condition
The UPS indicates the Fault condition by LCD display, emitting a continuous acoustic alarm.
During Fault condition, the UPS doesn’t supply Output power and so all the supplied devices are switched off.
7Communication Interfaces
The UPS is factory-equipped USB Communication Interfaces. On the UPS rear side there are the connectors of the
Interfaces. USB port can be connected via USB cable to the USB port of the protected device.
The USB signals are all isolated through photo-couplers from the dangerous voltages that are present inside
the UPS.
Connecting to the Web site www.tecnoware.com, it is possible to download, free of charge, the update UPS
management Software ViewPower.
.

EN LISH
User’s manual 10 Ups Pro
8Technical Characteristics
UPS Model Ups Pro
Power 1500 VA
(1050 W)
Technology Line Interactive Pure Sinewave with Stabilizer
Nominal Input Voltage Single-phase 2 0 Vac
Input Voltage Range +20% / -25%
Input/Output Frequency 50/60 Hz (automatic selection)
Input Frequency Range +/- 10%
Nominal Output Voltage Single-phase 2 0 Vac
Output Voltage Regulation
(Normal mode) Through AVR (Automatic Voltage Regulation)
Output Voltage Regulation
(Battery mode) +/- 5%
Output Inverter Waveform Sinewave
Accepted Overload 110%-60sec / 120%- 0sec / >120%-20msec
Certifications
CE
Standards: CEI EN 62040-1: 2008 (Low Voltage Directive) –
CEI EN 62040-2: 2006 (EMC Directive)
Efficiency 96%
Battery Type Lead acid, sealed, free maintenance
Number of batteries 1
Nominal Battery Voltage 24 Vdc
Battery Specifications 12 Vdc – 7 Ah - 6 cells
Backup Time (typical) 10 min
Battery Charge Time (typical) 4 hours
Audible Noise (at 1 meter) < 45 dBA
Environmental Operative Specification Temperature: 0-40 °C - Humidity 0-95% (without condensation)
Altitude: max .000 mt
Computer Interface 1 USB port
UPS Management Software Included Software Viewpower,
downloadable free of charge from www.tecnoware.com
Output sockets 2 UPS Outputs sockets (Italian/Schuko type) + 2 Filtered Outputs sockets
(Italian/Schuko type)
Dimension (W x H x D) 14,6 x 16 x 5 cm
Net Weight 9,5 Kg
Technical data may change without prior notice

EN LISH
Ups Pro 11 User’s manual
9Maintenance
9.1 UPS Cleaning
Before starting any cleaning operation, be sure that:
1. The AC Input Voltage for the UPS has been removed.
2. The UPS is OFF.
Use only a cloth dampened with water to clean the unit.
If UPS works in an environmental unusually dusty or dirty, remove the dirty from the ventilation holes.
Before restarting the UPS be sure it is completely dry. If any liquid gets inside the UPS, do not start the unit and
contact Technical Service immediately.
9.2 Battery
If the UPS is NOT going to be used for a long period of time, ensure that the batteries are left fully charged.
If the UPS has not been used for more than three months, go through the “First Start Up” procedure described in
the chapter 5 before using it again.
Please keep in mind that the batteries must be recharged at least once a month. Take in mind that batteries are
recharged automatically if the UPS works in Normal mode or if the UPS is off and connected to the AC Input Line.
Battery life strongly depends on the ambient temperature. There are also other factors like the number of charge-
discharge cycles, the discharge depth, humidity and altitude.
The recommended environmental specifications for a correct use of batteries are listed in the “Technical
Specifications” section.
9.3 Operator Safety
Whenever the UPS is not responding anymore to original characteristics, the UPS must be made non-operative and
every usage not authorised must be avoided. After it will be necessary to refer to qualified technical personnel.
Original safety characteristics might not be if, for example, the UPS has visible damage or irregular operation.

EN LISH
User’s manual 12 Ups Pro
10 Troubleshooting
Alarms and problems you may encounter during operating the UPS are given in the table below. Apply
the suggestions corresponding to each anomaly as described into the table.
If your anomaly is excluded or the suggested actions do not solve your problem, consult the Technical Service.
Please give the following information to the Technical Service:
 Model and serial number of the UPS, which can be found on the nameplate on the rear of the UPS.
 Description of anomaly.
Risk of electric shock: do not remove the cover. The UPS contains internal parts that are
at a high Voltage and are potentially dangerous, capable of causing injury or death by
electric shock.
There are no internal parts in the UPS that are user serviceable. Any repair or
maintenance work must be performed exclusively by qualified technical personnel
authorized by TECNOWARE.
TECNOWARE declines any responsibility if this warning is disregarded.
Warning to the technical personnel authorized for service: since internal components
are connected to the batteries, they will remain powered, and therefore dangerous,
even after the UPS has been disconnected from AC power mains. Before any repair or
maintenance work, disconnect the batteries, by removing the positive cable (red colour)
from the positive pole of the battery.
ANOMALY POSSIBLE CAUSE ACTION TO SOLVE
The UPS does not
turn on
ON/OFF button Press the ON/OFF button.
Batteries are flat Recharge the batteries for at least 4 hours.
Electronic board failure Refer to Technical Service.
The UPS always
function in Battery
mode
Input mains power cable is
disconnected.
Check the input mains power cable.
Check the presence of the electrical mains.
Input mains thermal fuse Check the thermal fuse and trigger it.
Black-out conditions / surge/
Over-Voltage or Low-Voltage Wait until the AC Input Line returns to normal conditions.
Electronic board failure Refer to Technical Service.
Battery Autonomy is
too short
Battery is not fully charged. Recharge the battery for at least 6 hours.
Electronic board failure Refer to Technical Service.
“OVERLOAD” alarm “OVERLOAD” condition Disconnect all devices that cause the overload condition.
“FAULT” alarm “FAULT” condition Check if UPS is in OVERLOAD condition.
Refer to Technical Service.
The UPS does not
communicate with
the Computer
The UPS Management
Software sends a
communication error
Check that the USB cable is correctly connected between the UPS
and the Computer.
The Software is not correctly
installed
Install correctly the specific Software for your Computer’s
Operative System.
If the described anomalies should continue despite the advised troubleshooting, or should they
manifest in any other form, please contact:
TECNOWARE SERVICE
www.tecnoware.com

EN LISH
Ups Pro 13 User’s manual
Conformity to the European Directives
TECNOWARE S.r.l. confirms that Ups Pro models comply with the req irements set o t in: the Low Voltage Directive (Safety)
2006/95/EC and following amendments, the EMC (Electro-Magnetic Compatibility) Directive 2004/108/EC and following
amendments.
The following standards were applied:
Low Voltage Directive (Safety): CEI EN 62040-1: 2008
EMC Directive (Electro-Magnetic Compatibility): CEI EN 62040-2: 2006
Product Disposal
UPS Ups Pro cannot be disposed as an rban waste, b t m st be treated as a separate waste. Any
violation is indictable with financial sanctions as per in force reg lations.
An incorrect waste disposal or an improper se of the same or of any parts can be damaging for the
environment and for h man health.
A correct waste disposal of prod cts having the d stbin symbol marked by a cross help to avoid
negative conseq ences to the environment and to h man health.
Lead Batteries
Ups Pro models contain lead acid, sealed, maintenance free batteries.
The batteries cannot be disposed as an rban waste, b t m st be treated in conformity with
2006/66/CE E ropean Directive; any violation is indictable with financial sanctions as established into
2006/66/CE E ropean Directive.

ITALIANO
Manuale utente 14 Ups Pro
Manuale Utente – Italiano
Avvisi di Sicurezza
 Leggere attentamente e completamente questo manuale prima di installare ed utilizzare il
gruppo di continuità TECNOWARE della serie Ups Pro, che in seguito verrà chiamato anche
semplicemente UPS.
 Conservare con cura questo manuale vicino all’UPS e consultarlo sempre prima di operare sullo
stesso.
 L'UPS deve essere utilizzato solo da personale opportunamente istruito. Per l’uso corretto e in
condizioni di sicurezza è necessario che gli operatori ed il personale di manutenzione si
attengano alle norme generali di sicurezza, in aggiunta alle norme specifiche contenute in
questo manuale.
 Rischio di shock elettrico: non rimuovere il coperchio. L’UPS presenta parti interne sotto
tensione che sono potenzialmente pericolose e possono provocare lesioni o morte per shock
elettrico.
 L’UPS non ha parti interne soggette a manutenzione da parte dell’utente. Interventi tecnici di
qualsiasi tipo devono essere compiuti solo da personale tecnico specializzato ed autorizzato da
TECNOWARE. In caso contrario TECNOWARE declina ogni sua responsabilità.
 Avviso per il personale tecnico autorizzato alla manutenzione: anche dopo aver spento l’UPS e
scollegato dalla rete elettrica, le parti interne sono ancora in tensione, essendo collegate alle
batterie, e quindi pericolose. Prima di effettuare qualsiasi tipo di riparazione o manutenzione,
scollegare le batterie, staccando il cavo positivo (di colore rosso) dal polo positivo della batteria
a cui è collegato.
 Il collegamento a terra dell’UPS secondo le norme vigenti è obbligatorio. La presa di Rete
Elettrica a cui è collegato l’UPS deve essere dotata di connessione a terra.
 In caso di assenza della Rete Elettrica (cioè durante il funzionamento in modo Batteria), non
staccare il cavo di alimentazione. In caso contrario non è garantita la continuità di terra alle
utenze collegate.
 Il cavo di alimentazione dell’UPS ha le funzioni di dispositivo di sezionamento. Per questo
motivo la presa di Rete Elettrica a cui l’UPS è collegato e/o il retro dell’UPS devono essere
facilmente accessibili per disconnettere facilmente il cavo di alimentazione in caso di pericolo.
 Rischio di shock elettrico in Uscita se l’UPS è acceso.
 Rischio di shock elettrico in Uscita se è presente la Tensione di Rete elettrica in Ingresso.
 Non ostruire le fessure o i fori di ventilazione e non appoggiare alcun oggetto sopra l’UPS. Non
inserire oggetti o versare liquidi nei fori di ventilazione.
 Installare l’UPS in ambiente chiuso, pulito e privo di umidità. Non esporre l’UPS alla luce diretta
del sole. Non avvicinare liquidi, gas infiammabili o sostanze corrosive.

ITALIANO
Ups Pro 15 Manuale utente
1Introduzione
Ups Pro è un UPS (Uninterruptible Power Supply), cioè un gruppo di continuità, di tipo Line Interactive ad Onda
Sinusoidale, realizzato appositamente per proteggere Mac Pro da qualsiasi avaria della rete elettrica (black-out,
sottotensioni, sovratensioni, microinterruzioni), causa dei frequenti danneggiamenti di Hardware e Software.
Quando è presente la tensione di rete elettrica, Ups Pro svolge le funzioni di stabilizzatore e filtra i disturbi
frequentemente presenti sulla linea elettrica (transienti, spike, interferenze, etc.), preservando in tal modo i
dispositivi collegati alla sua uscita; inoltre ricarica le batterie in modo ottimale. In caso di avaria della rete
elettrica, l’UPS continua ad alimentare le apparecchiature protette.
Ups Pro è dotato di un’interfaccia USB che può essere utilizzata per segnalare ad un generico elaboratore o
computer le condizioni di assenza rete e di fine autonomia: ciò rende possibile lo svolgimento delle funzioni di
salvataggio automatico dei dati durante un black-out prolungato.
Leggere attentamente questo manuale prima di utilizzare Ups Pro perché contiene
importanti avvisi di sicurezza per l’operatore ed utili consigli per un corretto impiego.
Questo manuale è una guida per installare e utilizzare correttamente l’UPS. Nel manuale
sono incluse importanti istruzioni di SICUREZZA per l’operatore e per una corretta
installazione dell’UPS e utili consigli per la manutenzione del prodotto e delle batterie.
Per ogni problema fare prima riferimento al manuale e poi rivolgersi al Servizio
Assistenza.
Ups Pro è soggetto a continui sviluppi e migliorie: di conseguenza può differire lievemente, in alcuni dettagli, da
quanto descritto nel presente manuale.
Questo manuale è relativo ai seguenti modelli:
•Ups Pro (1500 VA)
In questo manuale Ups Pro sarà chiamato anche semplicemente UPS.
2Caratteristiche enerali
Ups Pro presenta tutte le moderne caratteristiche che garantiscono massima affidabilità e sicurezza:
•Controllo a microprocessore di tutte le funzioni, garanzia di alta affidabilità.
•Stabilizzazione in uscita tramite AVR (Automatic Voltage Regulation).
•Protezione da sovraccarico sia nel modo di funzionamento normale che in modo batterie.
•Carica batterie di alte prestazioni che prolunga il tempo medio di vita delle batterie e ne garantisce una
ricarica ottimale.
•Accensione anche in condizioni di rete elettrica assente.

ITALIANO
Manuale utente 16 Ups Pro
•Riaccensione automatica dopo lo spegnimento per fine autonomia al ritorno della tensione di rete.
•Adattabilità automatica alla frequenza d’ingresso 50 o 60 Hz.
•Display LCD per visualizzare il valore della Tensione d’Ingresso e d’Uscita, la percentuale di carica delle
batterie, la percentuale di potenza utilizzata, le modalità di funzionamento e le condizioni di allarme e
guasto.
•Segnalazioni acustiche di vario tipo durante il normale funzionamento e che evidenziano le eventuali
condizioni di allarme.
•Comunicazione con il computer tramite porta di comunicazione USB.
•Rapida sostituzione delle batterie.
•Alta affidabilità.
•Elevato rendimento e basso costo d’esercizio.
•Dimensioni compatte.
•Curato design.
•Semplicità d’uso.
3Ricevimento e Collocazione
Al ricevimento dell’UPS, si consiglia di togliere subito l’imballo e di controllare lo stato dell’UPS. In caso di danni
dovuti al trasporto, annotarli sulla bolla di accompagnamento merce e contattare subito il fornitore.
Si consiglia di conservare l’imballo originale in luogo sicuro nell’eventualità futura che l’UPS dovesse essere
spedito per la manutenzione.
Si consiglia di prestare attenzione ai punti seguenti per la scelta di una corretta collocazione dell’UPS:
•L’UPS è progettato per operare in ambienti chiusi (come ad esempio gli uffici). Si consiglia perciò
d’installarlo in un luogo privo di umidità, polvere e fumo eccessivi.
•Consultare comunque il capitolo “Caratteristiche Tecniche” per i requisiti ambientali e controllare che il
luogo scelto rientri in tali specifiche.
•Durante il normale funzionamento l’UPS emette una quantità minima di calore. È perciò necessario
lasciare uno spazio libero di almeno 20 cm sia lateralmente che sul retro dell’UPS per permetterne una
sufficiente areazione.
•Non ostruire le fessure o i fori di ventilazione.
•Non inserire oggetti o versare liquidi nei fori di ventilazione.
•Non appoggiare alcun oggetto sopra l’UPS.
•Non avvicinare liquidi, gas infiammabili o sostanze corrosive.
•Installare l’UPS su superfici piane non inclinate.