TECO TVS26CVUVAH User manual

INVERTER VERTICAL SKINNY
WINDOW ROOM AIR CONDITIONER
User Manual
Cooling Only Model:
TVS26CVUVAH
Cooling & Heating Model:
TVS26HVUVAH
IMPORTANT NOTE:
Thank you for selecting a TECO quality Refrigerator. Please
read this manual carefully before installing or operating your new
appliance. Make sure to save this manual for future reference.
The design and specifications are subject to change without prior
notice for product improvement.
IMPORTANT NOTE:
Thank you for selecting a TECO quality Refrigerator. Please
read this manual carefully before installing or operating your new
appliance. Make sure to save this manual for future reference.
The design and specifications are subject to change without prior
notice for product improvement.
IMPORTANT NOTE:
Thank you for selecting a TECO quality Refrigerator. Please
read this manual carefully before installing or operating your new
appliance. Make sure to save this manual for future reference.
The design and specifications are subject to change without prior
notice for product improvement.
IMPORTANT NOTE:
Thank you for selecting a TECO quality Refrigerator. Please
read this manual carefully before installing or operating your new
appliance. Make sure to save this manual for future reference.
The design and specifications are subject to change without prior
notice for product improvement.
IMPORTANT NOTE:
Thank you for selecting a TECO quality Refrigerator. Please
read this manual carefully before installing or operating your new
appliance. Make sure to save this manual for future reference.
The design and specifications are subject to change without prior
notice for product improvement.
IMPORTANT NOTE:
Thank you for selecting a TECO quality Air Conditioner.
Please read this manual carefully before installing or
operating your new appliance. Make sure to keep this
manual for future reference.
The design and specifications are subject to change
without prior notice due to product improvement.

CONTENTS
IMPORTANT SAFETY INSTRUCTIONS
NAMES OF PARTS
INSTRUCTIONS FOR USE OF DRAIN OUTLET
CONTROL SETTING
MAINTENANCE
TROUBLESHOOTING
REPAIRS, SERVICE & WARRANTY
1
3
5
7
13
15
17

-1 -
Thank you for purchasing our product and thank you for placing your
confidence in us.
Read this manual carefully before use. Follow the instructions and keep this
manual for future reference.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of this appliance by a person responsible for their safety.
Young children should be supervised to ensure that they do not play with the
appliance.
Packing (e.g. wraps, polystyrene etc.) can be dangerous for children. There is a
risk of suffocation. Keep packaging materials away from children.
Follow the operating instructions and safety notices in this manual.
All images, illustrations and photos contained in this manual are for illustration
purposes only and may differ from your appliance.
The appliance is specifically constructed for domestic use only. The appliance
has not been designed or manufactured for professional use. TECO declines all
responsibility for damage deriving from improper use of the appliance.
Install the equipment correctly to ensure the required space size, including the
minimum allowable distance to adjacent structures. (Note: Refer to the
installation manual)
Please follow the correct wiring connection type when operating.
Do not remove any safety signs, stickers or labels from the device. Keep all
safety signs, stickers and labels clearly visible.
The sealed system contains refrigerant. Do not allow any sharp objects to
come in contact with the refrigerant system which may cause damage to the
refrigerant circuit.
This appliance contains a UV-C lamp.
If the UV-C lamp is damaged, it must be replaced by a special UV-C lamp or
assembly available from the manufacturer or its service agent.
Read the maintenance instructions before cleaning the appliance.
The appliance must be turned OFF and disconnected from the power supply
prior to cleaning or other maintenance.
IMPORTANT SAFETY INSTRUCTIONS

- 2 -
UV-C barriers bearing the ultraviolet radiation hazard symbol should not be
removed.
Improper use of the appliance or damage to the housing may result in the
escape of dangerous UV-C radiation. UV-C radiation may, even in small doses,
cause harm to the eyes and skin.
Do not operate UV-C lamps outside of the appliance.
Do not use the device in an explosive-hazardous room.
Do not use the device in a corrosive environment.
Stand the device upright and stable.
Do not use the device with wet hands.
Do not splash water on the appliance. It may cause malfunction or electric
shock.
Never insert any objects or your hands into the device.
Ensure that air inlets and outlets are not blocked.
Make sure the suction side is free of dust and loose objects
Always switch off and unplug appliance before cleaning.
When not using the device, turn off the device and unplug the power cord
from the power outlet.
Drain the collected condensate water before transportation and storage. Do
not drink. Harmful to health.
If the supply cord is damaged, it must be replaced by authorised TECO service
personal, service agent or similarly qualified persons in order to avoid a
hazard.
If any trouble arise, do not attempt to fix it yourself. Please contact TECO
service on 1300 660 037 (8:30am - 4pm Mon~Fri AEST).
Contact your local authorities for correct method of
disposal. Dispose of all packaging and/or appliances
in a responsible manner in accordance with local
regulations.

-3 -
①
③
②
④
⑤
⑥
⑦
⑧
⑨
NAMES OF PARTS
①Front panel
②Vertical louver blades (auto swing)
③Horizontal louver blades (manually swing)
④Indoor air inlet
⑤Sliding panel
⑥Display screen
⑦Control panel
⑧Power cord
⑨Indoor water outlet
Indoor

-4 -
PLEASE REFER TO INSTALLATION INSTRUCTIONS BEFORE INSTALLING
THE STANDARD FRAME ONTO YOUR WINDOW TO PREVENT THE UNIT
FROM FALLING OFF.
⑩Back panel
⑪Outdoor air inlet
⑫Outdoor water outlet
⑬Outdoor air outlet
⑭Standard mounting bracket
⑮Base plate
⑯Continuous drain outlet
⑩
⑪
⑬
⑭
⑮
⑯
⑫
Outdoor Window Kit

- 5 -
Cooling only model：
When the water full indicator "FL" appears, you can only drain it manually. Open
one of the drain ports 9, 12, and 16 in the parts diagram to drain;
Note: The continuous drain port of the cooling only model fitted with a rubber
water plug. In order to have a better cooling effect, please do not remove the
rubber water plug and connect the drain pipe except for the above-mentioned
water full condition, since the machine has self-evaporation technology, the
condensed water can improve the cooling capacity and energy efficiency.
Cooling & Heating model, automatic drain
1) During cooling/dehumidification operation, the machine has self-evaporation
technology, Condensed water helps dissipate heat, when the water full
indicator "FL" appears in ultra-high humidity weather, you can manually open
one of the drain ports 9, 12, 16 to drain, or automatically drain after shutting
down (Delay 15 minutes to start smart drainage after shutdown)
2) Continuous drainage during the heating operation, no need for manual
drainage.
Note: When installing the heating and cooling model, please install the
continuous drain hose, then the machine will automatic drain through the
drain outlet according to the program setting.
Rubber water plug
Cooling only model
TVS26CVUVAH
Continuous drain outlet
Drain hose
Cooling and Heating model
TVS26HVUVAH
INSTRUCTIONS FOR USE OF DRAIN OUTLET

- 6 -
Install instruction of continuous drain hose for heating and cooling model：
Machine
Drain hose Continuous drain outlet
As shown in the figure, when installing the drain hose, please firmly
insert the hose to the drain outlet, make sure the drain hose is
inclined downward, the inclination angle is more than 1 degree,
ensure the drain hose is free of kinks and wrinkles, and there is no
foreign matter in it. Otherwise, the drain hose may be blocked.
Back Front
Note: The window type room air conditioner must be installed
with compliance to the Building Code of Australia, Local
Government or body corporate requirements. Please consult
your local government or body corporate or builder or air
conditioning contractor.

Not applicable
Child lock
icon
Digital display
Fan speed icon
Celsius icon
Time icon
Auto icon
Heat icon #Cool icon
Dry icon
Fan icon
Swing icon
Up/Down key
Timer key
Child lock
Power key
Ⅰ. The operation panel & Remote controller
Timer icon
-7 -
CONTROL SETTING
Note: # Cooling only model doesn't have the Heat icon.

Fan speed：
Work mode flowchart：
Mode switching sequence：Auto→Cool→Dry→Heat→Fan
Note: Cooling only model doesn't have Heat mode；
………………1 st speed，1 blade，display shows 1；
………………2 nd speed，2 blades，display shows 2；
………………3 rd speed，3 blades，display shows 3；
………………4 th speed，4 blades，display shows 4；
………………5 th speed，5 blades，display shows 5；
………………6 the speed，6 blades，display shows 6；
………………7 the speed，7 blades，display shows 7；
………………Turbo mode，8 blades，display shows tu；
………………Auto speed，8 blades，display shows Au；
-8 -

Auto
Cool Dry Heat # Fan
Child lock
Sleep
Swing
FOLLOW Me
Fan speed
Quiet Wind speed
blade
Signal icon
Time icon
Celsius icon
Turbo icon
Auto fan
speed icon
-9-
Note: # Cooling only
model dosen't have
the Heat icon.

-10 -
①. Power: ON & OFF of the air-conditioner
②. Mode：Press this button to switch between auto→ cooling→heating→ dry→ fan
modes (the cooling only model don't have heating mode).
③. Up/Down: Press to increase/decrease the temperature when in auto, cooling and
dehumidification modes, press to increase/decrease the time when setting timer.
④. Fan speed: Press to select t he fan speed:1st speed→2nd speed→3rd speed→4th
speed→ 5th speed→6th speed→7th speed→auto swing.
⑤. Swing: Press to turn on / off the swing function, which is available in all modes
⑥. Sleep: Press this key to turn on the sleep mode, after Icon blink 5 times,the display
luminance will be decreased 50%. The sleep mode is only available in the cooling and
heating modes.(If the machine has heating function)
⑦. Timer: Press to set time to turn off the machine when it is on, press to set time to
turn on the machine when it is in standby state. Press Up/Down buttons to adjust
the setting time from 0.5h~24h, before 10 hours,adjust 0.5 hour per press, after 10
hours, adjust 1 hour per press. If you keep pressing the up or down button, the time
will continuously increase or decrease.
⑧. Follow me: Press this button to turn on/off Follow me function. Follow me
function is only valid in cooling and heating mode, and can only be turned on by the
remote control. When the machine is running, press the Follow me button on the
remote control to start the function. The corresponding icon on machine and
controller is displayed. The status of the machine remains unchanged. A sensor
located in the remote controller senses the room temperature and relays the
information to the device every 3 minutes.
⑨. LED: Press to turn on/turn off the LED display on machine.
⑩. Turbo: Press this key to turn on / off Turbo fan. The machine is forced to run at
Turbo fan speed for 30 minutes, then restore the previous fan speed, this button is
only effective in cooling mode.
⑪. My mode: Press this key to adjust to My mode, at this time the mode is auto
mode and the setting temperature is 26℃。
⑫. Quiet: Press this key to adjust the wind speed to quiet wind, digital display shows
"LO", press this Key or any fan speed key again to exit the quiet wind and return to
the previous wind speed operation.
⑬. Self clean: Press to start self clean after power off, LED "88" display shows“SC”,
compressor will stop and machine will blow air in quiet fan speed for 30 minutes.
⑭. Lock: Press Fan + Timer keys at the same time on machine and remote controller
to turn on / off the child lock function.

-11 -
ⅡWorking mode operation
1. Auto mode
Press the mode key to select the automatic mode while the machine is on.
At this time, the corresponding indicator on the panel lights up.
In this mode, the product will automatically adjust the corresponding
operating function according to the current ambient temperature.
The cooling function is operated when the ambient temperature is higher than 27 °
C, the set temperature is 24 ℃, and the default wind speed is automatic wind.
The dehumidification function is operated when the ambient temperature is 24
°C to 27 ° C, the set the wind speed is 1st.
The air supply function is operated when the ambient temperature is 20 to 24 °
C,Wind speed defaults to 4 levels, showing ambient temperature .
The heating function is operated when less than 20 ° C,The wind speed is auto and
the set temperature is 24 ℃ (if no heating Functional products still operate the air
supply function).
2. Cooling and heating modes (cooling only models without heating mode)
Select the cooling or heating mode by pressing the mode key while the
power is on or the timer is on. At this time, the corresponding indicator
lights on the panel.
Press the up and down keys to set the appropriate temperature. The
setting range is 16 ~ 30 ° C (60-86 ° F). Each time you press the up or
down key, the temperature will rise or fall by 1 ° C or 1 °.
Press the wind speed button to select the appropriate wind speed, you can
choose 1-7 speed and TURBO wind speed.
Press the swing key to turn the left and right swing function on or off.
The wind speed can be adjusted. The next time the auto mode is started, the
wind speed returns to the system setting.
Follow me, Turbo, mute in auto mode, self-cleaning function is effective
Auto wind speed: (Tr represent room temperature, Ts represent setting
temperature)
When Tr-Ts≥3 ℃, the wind speed runs at 7th speed;
When Ts + 1 ℃ ≤Tr ＜ Ts + 3 ℃, the wind speed runs at 4th speed
When Tr-Ts <1 ℃, wind speed runs at 1st speed
Wind speed changes from low wind to high wind without 3min delay, wind
speed changes from high wind to low wind with 3min delay

-12 -
3. Dry mode
Press the mode key to select the dehumidification mode while the
machine is on. The corresponding indicator lights up.
Set temperature is same as cooling mode.
Wind speed is not adjustable.
Press the swing key to turn the swing function on or off.
4. Fan mode
When the machine is on, press the mode key to select the air supply
mode. The corresponding indicator lights up
Press the fan speed button to select the appropriate wind speed, from 1-7
speeds.
Wind speed is not adjustable.
Press the swing key to turn the swing function on or off.
Auto wind speed in air supply mode:
When Tr ＞ 27 ℃, t he wi nd speed r uns at 7t h speed;
When 24 ＜ Tr≤27 ℃, the wind speed runs in the 4th speed;
When Tr≤24 ℃, the wind speed runs at 1st speed;
Wind speed changes from low wind to high wind without 3min delay, wind
speed changes from high wind to low wind with 3min delay
5. Sleep mode
When power on, press the sleep button on the remote control to turn on
the sleep function which will increase (cooling) or decrease (heating) by
1℃ per hour for the first 2 hours. Thereafter it keeps this new temp. for
6hrs’ running then machine will be switched off automatically, which
means machine will be turned off automatically after 8 hours of sleep
mode running. This function is only effective in cooling and heating modes.
(If the machine has heating function)
The fan speed will lower to 4th speed directly,If fan speed lower than level
four before Sleep mode, then fan speed will decrease one level per 0.5
hour until fan speed reaches level 1 and stay at level 1 thereafter. Note: If
press Turbo or Fan or Mode button, sleep mode will be cancelled
automatically

6. UV sterilization function
When power on, the UV sterilization function is activated intelligently.
It is turned on for 20 minutes and turned off for 20 minutes, and it works
in cycles.

-13 -
Cleaning: Turn off the unit and remove the power plug before
cleaning and maintenance.
1.Cleaning surface
Wash the surface with a soft, damp cloth. Do not use chemical reagents such
as benzene, alcohol, or gasoline. Otherwise the surface of the air conditioner
will be damaged or even the whole machine.
2. Cleaning of the filter net
If the filter net is clogged with dust which will affect performance. Please
clean the filter every two weeks.
Air inlet
Filter net
★Can only open 7-8 degrees
Self-cleaning state, the UV sterilization function is activated; after
self-cleaning, the UV sterilization function is turned off.
MAINTENANCE

-14 -
3. Water full treatment
When the water full indicator is displayed, the machine will stop working. In
this case, it is necessary to remove the excess condensate water. Remove
indoor condensate drain plug or the outdoor condensate drain plug to drain
out the condensate water.
Remarks：
When draining water through the indoor drain plug, place a container below
to prevent the water from spilling onto the floor below.
Save after season：
1. Pull out the indoor drain plug, drain the water into a container,
or directly pull out the outdoor condensate drain plug to drain the
water out of the machine.
2. Adjust the fan mode to the low fan speed, or turn on the self clean
function, keep this operation for a long time until the inside coils are dry.
This operation will dry the inside of the machine and prevent mold.
3. Turn off the machine and unplug the power cord, wrap the power cord
and install the drain plug.
4. Remove the machine from the window and remove the mounting
bracket and keep it in good condition.
5. Cover air conditioner with plastic and store it in a dry place to prevent
dust from entering it. Do not let children have access to it.
6. Take out the battery of the remote controller.
①Place fingers on air inlet grille catch and pull to open, and then slide out the
filter net from the interior of the grille. (Note: the inlet grid can only be opened 7
~ 8 degrees, please do not use too much force to cause damage.)
②Put the filter into warm water (about 40 °C / 104 °F) that has been added with
neutral detergent. Rinse and dry in a cool place before inserting.
Remarks：
Store the machine in a dry place and ensure all accessories are well protected.

-15 -
Please check the following items before asking for repair or contacting service,
it may save you time and money. If problems persists, refer to your warranty
information for contact details.
TROUBLESHOOTING
Problem Cause Solution
Not
working
No power Turn on the power after
checking the power socket.
Water full indicator display
FL. Drain water
Is the ambient temperature
too low or too high?
Recommend to use the machine
between 7-35 ° C (44-95 ° F).
Room temperature is lower
than the set temperature in
cooling mode
Change set point temperature
Low ambient temperature
in dehumidification mode
Placed in a room with an
ambient temperature greater
than 17 ° C (62 ° F)
Insufficient
cooling
There is direct sunlight. Draw the curtains.
The doors and windows are
open or the frame is not
sealed, or there are too
many people or other heat
sources in the room.
Close the door or window or
seal the frame.
The filter is dirty Clean or replace the filter.
The air inlet or outlet is
blocked. Clear obstacles.

-16 -
Loud
noise
The air conditioner is not
installed correctly.
Check the frame and air
conditioner to ensure proper
and correct installation.
The
compress
or is not
working
Overheat protection initiated.
Wait for 3 minutes until the
temperature drops and then
turn it on.
The
remote
does not
work
Distance is too far. Operate the remote controller
in close proximity to the Air
Conditioner and make sure that
it is pointed towards the Air
Conditioner when operating
The IR receiver located in
the Unit does not receive
the IR signal transmitted
from the remote controller
The battery is out of power. Change battery。
Code
appears
on the
display
The appliance has a self
diagnosis system to
identify a number of
malfunctions.
Contact your local
authorized service centre.
NOTE: If any of the following occur, immediately power offthe air
condioner and unplugfrom the wall outlet. Contact your local service
center.
▪ Operaon starts or stops abnormally.
▪ Power fuse or switch oen trips.
▪ Fluids are splashed directly into the air condioner.
▪ Electrical cord is hot or cord insulation is damaged
▪ Other unusual noises emitted from the air condioner.
Do not attempt to repair the air conditioner yourself.
If the air conditioner is operated under abnormal conditions, it
may cause malfunction, electric shock or fire hazard.

-17 -
It is hazardous for anyone altering, repairing, servicing or testing a system
containing refrigerants (i.e. charging, discharging or opening up pipework of a
refrigeration system that uses hydrocarbon refrigerants).
Only an Authorised Service Person can carry out servicing or repairs to this
appliance.
REPAIRS, SERVICE & WARRANTY

www.teco.com.au
HCB-V1E&OE