Tektronix MTS400 Series User manual

Instructions
MTS4UP Upgrades
MTS400 Series and MTS400P MPEG Test Systems
075-0979-00
*P075097900*
075097900
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com

Copyright ©Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or
suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
HIn North America, call 1-800-833-9200.
HWorldwide, visit www.tektronix.com to find contacts in your area.

MTS4UP MTS400 Series Upgrade Kits i
Table of Contents
General Safety Summary iii...................................
Service Safety Summary v....................................
Kit Description 1............................................
Upgrade Kits Covered by These Instructions 1..........................
Minimum Tool and Equipment List 3..................................
Kit Parts Lists 3...................................................
Upgrade Instructions 9.......................................
Option UPG Software Upgrade 10..............................
Hardware Upgrades (MTS415 and MTS430) 15...................
Access the Module Bay 15...........................................
MTS4UP IPTVD Upgrade Instructions 17...............................
MTS4UP GBE Upgrade Instructions 19.................................
MTS4UP CF, EP, QB2, or VS Upgrade Instructions 20.....................
Replace the Cabinet 23..............................................
Restore the Operating System 24......................................
Software Upgrade Instructions 31......................................
Software Key Upgrade Instructions 37..................................
Hardware Upgrades (MTS400P) 38.............................
Software Upgrade 38................................................
Access the Module Bay 43...........................................
MTS4UP IPTVP Upgrade Instructions 46...............................
Option LX, Option SX, or Option ZX SFP Module Upgrade 53.....

Table of Contents
ii MTS4UP MTS400 Series Upgrade Kits

MTS4UP MTS400 Series Upgrade Kits iii
General Safety Summary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
Use Proper Power Cord. Use only the power cord specified for this product and
certified for the country of use.
Ground the Product. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Ground Equipment connected to the Product. Ensure that any equipment
connected to this product is grounded and at the same potential.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
Power Disconnect. The power cord disconnects the product from the power
source. Do not block the power cord; it must remain accessible to the user at all
times.
Do Not Operate Without Covers. Do not operate this product with covers or panels
removed.
Use Proper Fuse. Use only the fuse type and rating specified for this product.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Do Not Operate With Suspected Failures. If you suspect there is damage to this
product, have it inspected by qualified service personnel.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Provide Proper Ventilation. Refer to the manual’s installation instructions for
details on installing the product so it has proper ventilation.
ToAvoidFireor
Personal Injury

General Safety Summary
iv MTS4UP MTS400 Series Upgrade Kits
These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
These terms may appear on the product:
HDANGER indicates an injury hazard immediately accessible as you read the
marking.
HWARNING indicates an injury hazard not immediately accessible as you
read the marking.
HCAUTION indicates a hazard to property including the product.
The following symbols may appear on the product:
CAUTION
Refer to Manual
Protective Ground
(Earth) Terminal Standby
Terms in this Manual
Symbols and Terms
on the Product

MTS4UP MTS400 Series Upgrade Kits v
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary before performing any service
procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.

Service Safety Summary
vi MTS4UP MTS400 Series Upgrade Kits

MTS4UP MTS400 Series Upgrade Kits 1
Kit Description
This document provides instructions for performing hardware and/or software
and option key upgrades on the following Tektronix products:
HMTS400 Series MPEG Test Systems (MTS415 and MTS430)
HMTS4SA MPEG Test System
HMTS400P MPEG Test System
Upgrade Kits Covered by These Instructions
HMTS4UP UPG -- This kit provides a software upgrade for your MTS4xx
systems. This upgrade is included with all of the hardward updates, or may
be ordered separately.
As the user of an MTS400 Series MPEG Test System, you will be familiar with
the software key (or dongle) that must be attached to your unit before you can
open any of the MTS400 Series applications. Two styles of software key are
available, each performs the same function: parallel port or USB (MTS4SA
only). The option key string supplied with this upgrade kit is generated using the
serial number of the software key and the list of options to be licensed.
NOTE. Only the software applications already installed on your MPEG test
system will be available after the upgrade. If additional applications are
required, contact your Tektronix representative.
HMTS4UP IPTVD - This kit adds an IPTV Gigabit Ethernet interface with a
10/100/1000Base-T electrical port to your MTS415 or MTS430. When you
install the IPTV interface card you must remove any other installed optional
interface cards (options GBE, CF, EP, QB2, or VS).
There are three optical length input options available for option IPTVD:
HMTS4UP LX -- Adds a 1000Base-LX wavelength optical port with LC
connector (single mode 1310 nm).
HMTS4UP SX -- Adds a 1000Base--SX short wavelength optical port with
LC connector (multimode 850 nm).
HMTS4UP ZX -- Adds a 1000Base-ZX wavelength optical port with LC
connector (multimode 1550 nm).

Kit Description
2MTS4UP MTS400 Series Upgrade Kits
HMTS4UP GBE -- This kit adds a Gigabit Ethernet interface and IP Analysis
software to your MTS415 or MTS430 (SFP required). This kit may be
combined with any of the following hardware upgrade kits.
There are also four optical length input options available with option GbE:
HMTS4UP LX -- Adds a 1000Base-LX wavelength optical port with LC
connector (single mode 1310 nm).
HMTS4UP SX -- Adds a 1000Base--SX short wavelength optical port with
LC connector (multimode 850 nm).
HMTS4UP ZX -- Adds a 1000Base-ZX wavelength optical port with LC
connector (multimode 1550 nm).
HMTS4UP CU -- adds a 1000Base-T electrical port with RJ45 connector.
HMTS4UP CF -- This kit adds a COFDM DVB-T interface to your MTS415
or MTS430 instrument. This kit may only be combined with the MTS4UP
GBE kit.
HMTS4UP EP -- This kit adds a QPSK/8PSK interface to your MTS415 or
MTS430 instrument. This kit may only be combined with the MTS4UP
GBE kit.
HMTS4UP QB2 -- This kit adds a QAM B interface to your MTS415 or
MTS430 instrument. This kit may only be combined with the MTS4UP
GBE kit.
HMTS4UP VS -- This kit adds an 8VSB interface to your MTS415 or
MTS430 instrument. This kit may only be combined with the MTS4UP
GBE kit.
HMTS4UP IPTVP -- This kit adds an IPTV Gigabit Ethernet interface with a
10/100/1000Base-T electrical port to your MTS400P.
There are three optical length input options available for option IPTVP:
HMTS4UP LX -- Adds a 1000Base-LX wavelength optical port with LC
connector (single mode 1310 nm)
HMTS4UP SX -- Adds a 1000Base--SX short wavelength optical port with
LC connector (multimode 850 nm).
HMTS4UP ZX -- Adds a 1000Base-ZX wavelength optical port with LC
connector (multimode 1550 nm).