Teledyne Lecroy PPE6KV-A User manual

User Manual
PPE6
KV-A
High Voltage
Passive Probe

PPE6KV-A High-voltage Passive Probe User Manual
© 2021 Teledyne LeCroy, Inc. All rights reserved.
Users are permitted to duplicate and distribute Teledyne LeCroy documentation for
internal training purposes only. Resale or unauthorized duplication of Teledyne LeCroy
documentation materials is strictly prohibited.
Teledyne LeCroy is a registered trademark of Teledyne LeCroy, Inc. Other product or
brand names are trademarks or requested trademarks of their respective holders.
Information in this publication supersedes all earlier versions. Specifications are subject
to change without notice.
933979-00 Rev A
ppe6kv-a-user-manual_01oct21.pdf
October, 2021

User Manual
1
Contents
Safety Instructions ...............................................................................................................2
IEC Safety Symbols......................................................................................................... 2
Safety Precautions ......................................................................................................... 2
Voltage vs. Frequency Derating Curve .......................................................................... 3
Input Impedance vs. Frequency Derating Curve........................................................... 4
Specifications .......................................................................................................................5
Electrical Characteristics ............................................................................................... 5
Environmental Characteristics....................................................................................... 5
Physical Characteristics................................................................................................. 5
Overview ................................................................................................................................6
PPE6KV-A Accessories................................................................................................... 7
Voltage Derating for Accessories .................................................................................. 8
Operation ...............................................................................................................................9
Grounding the Probe....................................................................................................... 9
Handling the Probe ......................................................................................................... 9
Adjustment Procedures......................................................................................................10
LF Compensation..........................................................................................................10
HF Compensation .........................................................................................................10
Maintenance........................................................................................................................11
Cleaning.........................................................................................................................11
Service ...........................................................................................................................11
Warranty ..............................................................................................................................12
Certifications.......................................................................................................................13
EC Declaration of Conformity - Safety.........................................................................13
Environmental Compliance ..........................................................................................13

PPE6KV-A High Voltage Passive Probe
2
Safety Instructions
Follow generally accepted safety procedures in addition to the precautions listed here.
The overall safety of any system incorporating this product is the responsibility of the
assembler of the system.
IEC Safety Symbols
These terms and symbols may appear on the probe body or in this manual.
CAUTION of potential damage to equipment, or WARNING of potential injury.
Attend to the accompanying information to protect against personal injury or
damage. Do not proceed until conditions are fully understood and met.
DANGER, High Voltage, risk of electric shock or burn.
EARTH (GROUND) TERMINAL
Safety Precautions
Use only as specified. The probe is intended to be used only with compatible Teledyne
LeCroy instruments. Use of the probe and/or the equipment it is connected to in a
manner other than specified may impair the protection mechanisms.
Do not overload;observe all terminal ratings. To avoid electric shock or fire, do not apply
any potential that exceeds the maximum rating of the probe and/or probe accessories,
whichever is less. Observe all terminal ratings.
Comply with the Voltage vs. Frequency Derating curve. When measuring higher
frequency signals, keep input voltages under the maximum limits shown in the Voltage
vs. Frequency Derating curve.
Use only accessories compatible with the probe and rated for the application.
Substituting other accessories than those specified in this manual may create a shock or
burn hazard.
Connect and Disconnect properly. Always make the connections from the probe input
leads to the probe accessories that you intend to use before making any connections to
a voltage source. Ensure connections between probe input leads and accessories are
secure before connecting to a voltage source. Do not connect/disconnect accessories
from a voltage source unless they are first connected to the probe input leads.
Do not excessively bend cables.
Use only within operational environment listed. Do not use in wet or explosive
atmospheres.

User Manual
3
Keep product surfaces clean and dry.
Avoid exposed circuitry. Do not touch exposed connections and components when
power is present.
Do not remove the probe casing. Removing the probe’s case or touching exposed
connections may result in electric shock. Refer all repair and maintenance to qualified
service personnel.
Handle with care. Probe tips are sharp and may puncture skin or cause other bodily injury
if not handled properly.
Keep fingers behind the finger guard of probe body and accessories.
Do not operate with suspected failures. Before each use, inspect the probe, leads and
accessories for damage such as tears or other defects. If any part is damaged, cease
operation immediately and sequester the probe from inadvertent use.
Voltage vs. Frequency Derating Curve
WARNING: The maximum input voltage rating of the probe decreases as the
frequency of the applied signal increases.
1
10
100
1 K
10 K
100000 1 M 10 M 100 M 1 G
Voltage (Vrms)
Frequency (Hz)
Typical Voltage Derating PPE6KV-A

PPE6KV-A High Voltage Passive Probe
4
Input Impedance vs. Frequency Derating Curve
1
10
100
1 K
10 K
100 K
1 M
10 M
100 M
1 10 100 1000 10000 100000 1 M 10 M 100 M 1 G
|Z| (Ohm)
Frequency (Hz)
Typical Input Impedance PPE6KV-A

User Manual
5
Specifications
Electrical Characteristics
Bandwidth 500 MHz
Rise Time (10-90%) 800 ps (typical)
Maximum Input Voltage (as defined in IEC 61010-031)
CAT II11000 Vrms or 1500 VDC
CAT I2, 3 or 2000 Vrms
No Measurement Category 4000 V transient overvoltage
6 kV (DC + peak AC)
Input Resistance (system ) 50 MOhms ±1%
Input Capacitance (system) 2.8 pF (typical)
Input Coupling 1 MOhm DC/AC
Compensation Range 10 to 30 pF (typical)
Attenuation Ratio 100:1
Voltage Coefficient (at DC) 0.00025%/V (typical)
1 Measurements performed on circuits directly connected to the low-voltage installation.
2 Measurements performed on circuits not directly connected to mains.
3 CAT I per IEC 61010-031:2008, No Measurement Category per IEC 61010-031:2015.
Environmental Characteristics
Operating Temperature 0oto 50oC
Non-operating Temperature -40oto 70oC
Operating Humidity 90% max relative humidity up to +31° C,
decreasing linearly to 50% at +50° C
Operating Altitude 2000 m
Non-operating Altitude 15000 m
Pollution Degree 2, operating environment where normally only dry,
non-conductive pollution occurs. Temporary
conductivity caused by condensation is expected.
Physical Characteristics
Cable Length 2 m (6.56 ft)
Probe Tip Diameter 8.6 mm (0.34 in)
Probe Weight 80 g (0.18 lb)

PPE6KV-A High Voltage Passive Probe
6
Overview
The PPE6KV-A is a general purpose, high voltage probe with a 100:1 attenuation. Its fast
rise time and accurate frequency response make it suitable for a variety of measurement
applications.
The following items are delivered with the PPE6KV-A probe. Please check the delivery for
completeness. If any item is missing, send a message to our service department and we
will send you the missing item immediately.
Replacement accessories may be purchased with probe kit PK-112. Contact your local
sales office for probe kits.
See the Voltage Derating for Accessories on p.8.
WARNING: Use the ground lead only for connections to earth ground.
CAUTION: The accessories provided with the probe have been safety tested. Do
not use any other accessories than those originally provided.

User Manual
7
PPE6KV-A Accessories

PPE6KV-A High Voltage Passive Probe
8
Voltage Derating for Accessories
Accessory
Accessory Voltage Rating
Derated Max. Input Voltage for
Combined Probe & Accessory
BNC Adapter
100 V No Measurement Category1
100 V No Measurement Category
Sprung Hook
1000 V CAT II 2
1000 V CAT II
Crocodile Clip 1000 V CAT III 3
1000 Vrms CAT II
1500 VDC CAT II
Flexible Security Adapter 1000 V CAT III
1000 Vrms CAT II
1500 VDC CAT II
IEC/EN 61010-031:2015 Definitions.
1. No Rated Measurement Category applies to other circuits that are not directly connected to the
mains supply
2. Measurement Category II (CAT II) applies to test and measuring circuits connected directly to
utilization points (socket outlets and similar points) of the low-voltage mains installation
3. Measurement Category III (CAT III) applies to test and measuring circuits connected to the
distribution part of the building’s low-voltage mains installation.
WARNING. Each accessory has a different measurement category (CAT) rating.
The voltage and CAT rating of the probe must be derated to the values in the
table above when used with the corresponding accessory.
WARNING. To avoid risk of shock or fire, do not exceed either the voltage rating
or category ratings of the probe or the probe accessory, whichever is the lesser
of the two. Use only the accessories provided with the probe.
WARNING. To avoid risk of shock or fire, keep the probe body and output cable
away from the circuits being measured. Keep your fingers behind the finger
guard of the probe.

User Manual
9
Operation
The PPE6KV-A is rated for 1000 Vrms or 1500 VDC CAT II.
CAUTION: The maximum input voltage decreases as frequency increases.
Observe the Voltage vs. Frequency derating curve on p.3 and the Voltage
Rating for Accessories table on p.8.
To meet all specifications, warm the probe and instrument at least 20 minutes before
use, and always operate within the safe environmental conditions.
Grounding the Probe
Connect the probe to the oscilloscope input, then connect the ground lead to earth
ground before performing any measurements. Note that all accessible metal parts are
connected to the BNC instrument connector (GND), except for the probe tip and the BNC
center conductors.
CAUTION: The PPE6KV-A probe is designed for ground-referenced
measurements only.
Handling the Probe
To avoid any injury, handle the probe with care, especially the sharp contact tip.
Note that the probe cable is a sensitive part of the probe. Do not damage the cable
through excessive bending or pulling.
Avoid mechanical shock to this product in general to guarantee accurate performance
and protection.

PPE6KV-A High Voltage Passive Probe
10
Adjustment Procedures
The probe can be compensated for low frequency (LF) and high frequency (HF). Proper
compensation of the probe is required to assure amplitude accuracy of the waveform
being measured. Compensation matches the probe’s cable capacitance to the
oscilloscope’s input capacitance. This matching assures good amplitude accuracy from
DC to upper bandwidth limit frequencies.
LF and HF compensation should be adjusted when the probe is first connected to the
oscilloscope, or transferred between oscilloscopes.
LF Compensation
1. Apply a 1 kHz square wave to the probe. You can use the CAL output on the
oscilloscope front panel.
2. Using the supplied trimmer tool, adjust the LF trimmer on the BNC
compensation box until you achieve an optimum, flat-topped square wave.
HF Compensation
1. Remove the plastic caps from the HF trimmers on the BNC compensation box.
2. Using the supplied trimmer tool, adjust first HF1 then HF2 until you achieve an
optimum square-wave response.
Under Compensated
Over Compensated
Optimum Compensation
LF trimmer
HF1
HF2

User Manual
11
Maintenance
Cleaning
Clean the exterior of the probe using a soft cloth moistened with distilled water or
isopropyl alcohol solution. Do not use abrasive agents, strong detergents or other
solvents that may damage the probe. Dry the probe thoroughly before using. Clear
receptacles on accessories of debris before connecting to the probe.
CAUTION. The probe case is not sealed. Do not immersed it in liquid or allow
moisture to penetrate it. Keep probe body and all accessories clean and dry.
Service
Defective Probes
Return defective probes to a Teledyne LeCroy service facility for diagnosis and exchange.
Defective probes must be returned in order to receive credit for the probe core.
A defective probe under warranty will be either repaired or replaced with a factory
refurbished probe. A defective probe not under warranty can be exchanged for a factory
refurbished probe. A modest fee is charged for this service.
Returning a Probe
Contact your local Teledyne LeCroy service center for calibration or other service. If the
product cannot be serviced on location, the service center will give you a Return Material
Authorization (RMA) code and instruct you where to ship the product. All products
returned to the factory must have an RMA.
Return shipments must be prepaid. Teledyne LeCroy cannot accept COD or Collect
shipments. We recommend air-freighting. Insure the item you’re returning for at least the
replacement cost.
1. Remove all accessories from the probe.
2. Pack the probe in its case. If possible, include all tips, but not the manual.
3. Pack the case in its original shipping box, or an equivalent carton with adequate
padding to avoid damage in transit.
4. Mark the outside of the box with the shipping address given to you by Teledyne
LeCroy. Be sure to add the following:
•ATTN:<RMA code assigned by Teledyne LeCroy>
•FRAGILE
5. If returning a probe to a different country: contact Teledyne LeCroy Service for
instructions on completing your import/export documents.

PPE6KV-A High Voltage Passive Probe
12
Service Centers
For a complete list of offices by country, including our sales and distribution partners,
visit: teledynelecroy.com/support/contact
Teledyne LeCroy
700 Chestnut Ridge Road
Chestnut Ridge, NY, 10977, USA
US Support and Service:
Ph: 800-553-2769 / 845-425-2000
FAX: [phone]
[e-mail]
Warranty
Teledyne LeCroy warrants this oscilloscope accessory for normal use and operation within
specification for a period of one year from the date of shipment. Spare parts, replacement
parts and repairs are warranted for 90 days.
In exercising its warranty, Teledyne LeCroy, at its option, will either repair or replace any
assembly returned within its warranty period to the Customer Service Department or an
authorized service center. However, this will be done only if the product is determined by
Teledyne LeCroy’s examination to be defective due to workmanship or materials, and the
defect is not caused by misuse, neglect, accident, abnormal conditions of operation, or
damage resulting from attempted repair or modifications by a non-authorized service facility.
The customer will be responsible for the transportation and insurance charges for the return
of products to the service facility. Teledyne LeCroy will return all products under warranty with
transportation charges prepaid.
This warranty replaces all other warranties, expressed or implied, including but not limited to
any implied warranty of merchantability, fitness or adequacy for any particular purposes or
use. Teledyne LeCroy shall not be liable for any special, incidental, or consequential damages,
whether in contract or otherwise.

User Manual
13
Certifications
Teledyne LeCroy certifies compliance to the following standards as of the date of
publication. See the EC Declaration of Conformity shipped with the product for current
certifications.
EC Declaration of Conformity - Safety
The product meets the intent of EC Directive 2014/35/EU for Product Safety. Compliance
was demonstrated to the following specifications as listed in the Official Journal of the
European Communities:
IEC/EN 61010-031:2015 Safety requirements for electrical equipment for measurement,
control and laboratory use – Part 031: Safety requirements for handheld probe
assemblies for electrical measurement and test.
Environmental Compliance
End-of-Life Handling
The product is marked with this symbol to indicate that it complies with the
applicable European Union requirements to Directives 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE).
The product subject to disposal and recycling regulations that vary by country and
region. Many countries prohibit the disposal of waste electronic equipment in standard
waste receptacles. For more information about proper disposal and recycling of your
Teledyne LeCroy product, visit teledynelecroy.com/recycle.
Restriction of Hazardous Substances (RoHS)
Unless otherwise specified, all materials and processes are compliant with RoHS
Directive 2011/65/EU in its entirety, inclusive of any further amendments or
modifications of said Directive.

933979-00 Rev A
October, 2021