Teledyne Platinum User manual

Platinum/Optima
CVE Pocket Guide

Use and Disclosure of Data
Information contained herein is classified as EAR99 under the U.S. Export
Administration Regulations. Export, reexport or diversion contrary to U.S.
law is prohibited.
Platinum/Optima
CVE Refrigerated
Sampler
Pocket Guide
This pocket guide is not intended to replace
the instruction manual. Read the instruction
manual thoroughly before operating the
sampler.
COPYRIGHT © 2018 by
Teledyne ISCO
4700 Superior St.,
Lincoln, Nebraska, U.S.A. 68504
Phone: [phone]
Toll Free: [phone]
FAX: [phone]
Part Number: 69-2303-214
Released: October 2018

iii
Platinum/Optima
CVE Refrigerated
Sampler
Pocket Guide
Table of Contents
1. Introduction
1.1 Features .......................1-1
1.2 Specifications ...................1-6
2. Installation
2.1 Sampler Installation Overview .....2-1
2.2 Positioning the Sampler ..........2-2
2.3 Connecting Power ...............2-5
2.4 Installing a Bottle Kit ............2-7
2.4.1 24-1 Liter ................2-9
2.4.2 4-15 Liter (Platinum only). . 2-10
2.4.3 12-2.5 Liter ..............2-11
2.4.4 Single Bottle Configuration . 2-12
2.5 Attaching the Suction Line .......2-13
2.5.1 Vinyl Suction Line ........2-14
2.5.2 PTFE-lined Suction Line . . . 2-15
2.6 Attaching a Strainer ............2-16
2.6.1 Alternative to Strainers ....2-17
2.6.2 Max Unanchored Length . . . 2-17
2.7 Routing Suction Line and Strainer . 2-18
2.8 External Devices ...............2-19

iv
2.8.1 Other Device Connections . . 2-20
2.9 Configure and Program the Sampler . . .
2-24
2.10 Locking the Sampler ............2-24
2.11 Quick Start Guide ..............2-25
2.11.1 Program Ready Screen .....2-25
2.11.2 Program Configuration ....2-25
2.11.3 Sample Interval ..........2-27
2.11.4 Time Option .............2-27
2.11.5 Bottle Options ............2-27
3. Programming
3.1 Control Panel Description .........3-1
3.2 Getting Started .................3-3
3.3 Configuring the Sampler ..........3-4
3.3.1 Set Clock .................3-5
3.3.2 Bottle Configuration ........3-6
3.3.3 Suction Line ..............3-7
3.3.4 Rinse Cycle ...............3-8
3.3.5 Liquid Detector and Recycle . 3-9
3.3.6 Float Input ..............3-10
3.3.7 Output Pins ..............3-10
3.3.8 Refrigeration .............3-12
3.3.9 Program Lock ............3-13
3.3.10 Language Selection ........3-14
3.3.11 Set Unit ID ..............3-15
3.3.12 Diagnostics ..............3-16
3.3.13 Exit Configuration ........3-16
3.4 Sampling Program Overview .....3-16
3.4.1 Program Configuration ....3-18
3.4.2 Sampling Cycle
........................3-18
3.4.3 Sample Interval ..........3-21
3.4.4 Bottle Configuration
........................3-22
3.4.5 Program Run Options
........................3-24
3.4.6 Program Events

Table of Contents
v
........................3-27
3.5 Programming Steps .............3-28
3.5.1 Sample Pacing ...........3-28
3.5.2 Time Paced ..............3-29
3.5.3 Flow Paced ..............3-29
3.5.4 Bottles per Sample Event . . 3-30
3.5.5 Switch on Time Indexing . . . 3-31
3.5.6 Real Time Indexing .......3-31
3.5.7 Samples Per Bottle ........3-32
3.5.8 Run Continuously .........3-33
3.5.9 Sample Second ...........3-34
3.5.10 Flow Pulses, Analog Input . . 3-34
3.5.11 Composite Samples .......3-34
3.5.12 Pressurized Line ..........3-35
3.5.13 Timed Delay .............3-35
3.5.14 Auto Re-Run .............3-37
3.5.15 Timed Stop/Max Run Time . 3-37
4. Operation
4.1 Start a Sampler Program .........4-1
4.1.1 Sample Calibration .........4-2
4.1.2 Start Time Delay ..........4-3
4.1.3 The Run State .............4-3
4.1.4 Completed Program ........4-4
4.2 Pause or Stop a Running Program . . 4-5
4.3 Post Sampling Activities ..........4-6
4.3.1 View the Log ..............4-6
4.3.2 User Interface Icon ........4-10
4.3.3 Sample Bottle Removal ....4-12
4.4 Grab Samples ..................4-13
4.5 Velocity Control Valve ..........4-14
5. Maintenance
5.1 Periodic Maintenance Checklist ....5-1
5.2 Fuse ..........................5-2
5.3 Cleaning the Sample Chamber .....5-3
5.3.1 Sample Chamber Removal . . . 5-3
5.3.2 Sample Chamber Installation 5-4
5.3.3 Installing the Tubing .......5-4

vi
5.3.4 Sample Chamber Parts .....5-8
5.4 Compressor/Vacuum Pump .......5-10
5.5 Clean or Replace Wetted Parts ....5-11
5.5.1 Sampler Cleaning Guidelines . . .
5-11

1-1
Platinum/Optima
CVE Refrigerated
Sampler
Section 1 Introduction
1.1 Features
The sampler features are identified in Figures
1-1 through 1-4 and described in Table 1-1.
Figure 1-1 Sampler features (Front)
3
4
2
6
5
8
9
10
9

Platinum/Optima CVE Refrigerated Sampler
1-2
Figure 1-2 Sampler features (left side)
Figure 1-3 Sampler features (right)
15
16
1
12
1
17
7
14
13

Section 1 Introduction
1-3
Figure 1-4 Sampler features (back)
inside
14 18
11
13
Table 1-1 Sampler Features
Item Name Description
1 Control
Panel Cover
Protects the control panel
display and keypad. Can
be locked with user
supplied padlock.
2 Control
Panel
Supports user control and
programming of sampler
operation.
3 Discharge
Tube
Carries liquid to the
sample bottle.
4 Sample
Chamber
Sample is measured and
collected in the chamber
then discharged into
sample container.

Platinum/Optima CVE Refrigerated Sampler
1-4
5 Bottles Hold the collected
samples.
6 Sequential
Ta b l e
Rotates the bottles.
7 Refrigerator
Door
Protects the collected
samples inside the
refrigerated
compartment.
8 Latch Secures the door. The
latch mechanism may be
locked with a
user-supplied padlock.
9Level
Adjustment
Feet
The sampler includes four
level adjustment feet, one
at each corner. Use these
to keep the sampler
leveled.
10 Liquid
Detector
The liquid-sensing
electrodes detect fluid in
the sample chamber.
11 Lower Back
Cover
Access to Refrigeration
Module.
12 External
Device
Connection
Supports connections to
external devices such as
a flow meter for sample
pacing or 4-20mA.
Table 1-1 Sampler Features
(Continued)
Item Name Description

Section 1 Introduction
1-5
CAUTION
When lifting the sampler, cautiously lift with 2 people
(one on each side) with the door closed and latched.
Recommend using a lifting device.
13 Refrigeration
Module
Modular,
corrosion-resistant
refrigeration assembly
cools the refrigerated
compartment to a
user-selected.
Temperature of 2 to 5 °C
(35 to 41°F).
14 AC Mains
Line Cord
Connects to AC power
source.
15 Sample Line
intake
The sample intake line
connects here.
16 Air Vents Refrigeration air vents
17 Aux. Outputs Alarm, Fl. Start, Fl.
Start/Stop Run Status.
18 Top Back
Cover
Access to the vacuum
pump, fuses, and
electrical components.
Table 1-1 Sampler Features
(Continued)
Item Name Description

Platinum/Optima CVE Refrigerated Sampler
1-6
1.2 Specifications
Table 1-2 Specifications
General
Size
(H×W×D):
49 x 25.5 x 25.5 inches
124.4 x 64.7 x 64.7 cm
Weight
(empty):
97 kg
214 lbs.
Bottle
Configuration:
6 configurations available:
24, 1-liter PP
12, 2.5-liter PP
4, 15-liter PP
1, 20-liter PE
1, 10-liter PE or glass
Refrigerator
Body:
Molded fiberglass with UV
resistant gel coat.
Power
Requirements:
115 VAC ±10%, 60 Hz
Running current 12 amperes
230 VAC ±10%, 50 Hz
Running current 6 amperes
Installation
Category:
II
Pollution
Degree:
3
Maximum
Altitude:
2,000 meters
6,562 feet
Humidity: 0 to 100%
Operational
Temperature:
–29 to 49 °C
–20 to 120 °F

Section 1 Introduction
1-7
Tubing
Intake Suction
Tubing Length:
1to45m
3 to 150 feet
Material: Vinyl or PTFE-lined polyethylene
Inside
Diameter:
38inch (9 mm)
12inch (12mm)
Maximum
Suction Lift:
28 ft. (8.5 m) with 38inch suction
line
22 ft. (7.0 m) with ½ inch suction
line
Typical
Repeatability:
±5 ml or ±5%
Typical Line
Velocity at
Head Height:
115VAC/60Hz
28 ft. lift Pump
38inch suction line
3ft: 9.84ft/s
10ft: 7.38ft/s
20ft: 4.50ft/s
Typical Line
Velocity at
Head Height:
230 VAC/50Hz
28 ft. lift Pump
38inch (9 mm) suction line
1 m: 2.04 m/s (6.70 ft/s)
4 m: 2.10 m/s (6.89 ft/s)
7 m: 1.52 m/s (4.99 ft/s)
½ inch (12 mm)suction line
1 m: 1.74 m/s (5.71 ft/s)
3 m: 1.60 m/s (5.25 ft/s)
7 m: 1.33 m/s (4.36 ft/s)
Table 1-2 Specifications (Continued)

Platinum/Optima CVE Refrigerated Sampler
1-8
Liquid
Presence
Detector:
Wetted Liquid-sensor electrodes.
Controller
Enclosure
Rating:
NEMA 4X
IP66
Program
Memory:
Non-volatile ROM (Flash)
Flow Meter
Signal Inputs:
Pulses (dry contacts)
4-20 mA
0-5 VDC
0-10 VDC
Digital Alarms: 1 output, with 5 alarm
configurations
Number of
Composite
Samples:
Programmable from 1 to 999
samples.
Internal Clock
Accuracy:
1 minute per month at 25 °C
Software
Sample
Frequency:
1 to 9999 minutes, in 1-minute
increments
1 to 9,999 flow pulses
Table 1-2 Specifications (Continued)

Section 1 Introduction
1-9
Sampling
Modes:
Constant Time, Constant Volume
Variable Time, Constant Volume
Constant Flow, Constant Volume
Variable Flow, Constant Volume
Time and Flow Based Sampling
(refer to manual for more info)
Incremental Time per Bottle
Incremental Flow per Bottle
Sample
Volumes:
20 to 400 ml
Sample
Retries:
If no sample reaches the
liquid-sensor electrodes, recycle
will activate up to 4 attempts.
Rinse Cycles: Rinsing of suction line up to 4
rinses for each sample
collection.
Controller
Diagnostics:
Live diagnostics while sampling.
Table 1-2 Specifications (Continued)

Platinum/Optima CVE Refrigerated Sampler
1-10

2-1
Platinum/Optima
CVE Refrigerated
Sampler
Section 2 Installation
2.1 Sampler Installation Overview
The following sections provide general
instructions for placing the sampler into
operation. In typical applications, the steps are:
1. Positing the sampler (Section 2.2)
2. Connecting power. (Section 2.3)
3. Installing a bottle kit. (Section 2.4)
4. Attaching the suction line. (Section 2.5)
5. Attaching a strainer. (Section 2.6)
6. Routing the suction line and strainer.
(Section 2.7)
7. Connecting the sampler to external devices.
(Section 2.8)
8. Configuring and programming the sampler.
(Section 2.9)
9. Locking the sampler. (Section 2.10)

Platinum/Optima CVE Refrigerated Sampler
2-2
2.2 Positioning the Sampler
There are a few considerations when selecting a
site for the sampler. The foremost concern
should be personal safety.
The installation and use of this product may
subject you to dangerous working conditions
that can cause you serious or fatal injuries.
Take any necessary precautions before entering
the work site. Install and operate this product
in accordance with all applicable safety and
health regulations, and local ordinances.
WARNING
If this product is used in a manner not specified
in this manual, the protection provided by the
equipment may be impaired.
WARNING
This product has not been approved for use in
hazardous locations as defined by the National
Electrical Code.
WARNING
The sampler is heavy. When lifting, use a
two-person lift from the right and left sides. When
possible, move the sampler using a two-wheeled
hand cart from the side. To prevent damage to the
refrigeration system, do not tip the sampler more
than 45°.